TS3-0155-32S-P1

OC-3 ETC2 | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

Features

„ Compliant with 155 Mbps ATM and SONET OC-3 SDH STM-1 (S1.1) „ Industry standard 1×9 footprint „ SC duplex connector „ Single power supply 3.3 V „ Differential LVPECL inputs and outputs „ Compatible with solder and aqueous wash processes „ Class 1 laser product complies with EN 60825-1

Description

The TS3-0155-32S-P1-X transceivers utilizing 1310 nm MQW laser diodes are fully compliance to the 155 Mbps A TM and SONET OC-3 SDH STM-1 standard, and designed in industry standard 1 ×9 package with SC duplex connector. The transmitter section is a class 1 laser which is compliant to International Safety Standard EN 60825-1.

Ordering Information

PART NUMBER INPUT/OUTPUT SIGNAL DETECT VOLTAGE TEMPERATURE TS3-0155-32S-P1 DC/DC LVPECL 3.3 V 0°C to 70 °C TS3-0155-32S-P1-E DC/DC LVPECL 3.3 V −40°C to 85°C Absolute Maximum Ratings PARAMETER SYMBOL MIN MAX UNITS NOTE Storage Temperature TS −40 85 °C Supply V oltage Vcc −0.5 6.0 V Input V oltage VIN −0.5 Vcc V Output Current Io --- 50 mA Operating Current IOP --- 400 mA Soldering Temperature TSOLD --- 260 °C 10 seconds on leads

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V

155 Mbps ATM/SONET OC-3/SDH STM-1

Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 2/10 Date: 2003/02/17 http:// www.ritekom.com Operating Environment PARAMETER SYMBOL MIN MAX UNITS NOTE Ambient Operating Temperature (TS3-0155-32S-P1) TAMB 0 70 °C Ambient Operating Temperature (TS3-0155-32S-P1-E) TAMB −40 85 °C Supply V oltage Vcc 3.1 3.5 V Transmitter Electro-optical Characteristics (Vcc = 3.1 V to 3.5 V , TS3-0155-32S-P1: TA = 0 °C to 70 °C, TS3-0155-32S-P1-E: TA = −40 °C to 85°C) PARAMETER SYMBOL MIN TYP . MAX UNITS NOTE Data Rate B 50 155 200 Mb/s Output Optical Power 9/125 µm fiber Pout −15 --- −8 dBm Average Extinction Ratio ER 8.2 --- --- dB Center Wavelength λC 1261 1310 1360 nm Spectral Width (RMS) ∆λ --- --- 4 nm Rise/Fall Time (10−90%) Tr, f --- 1 2 ns Output Eye Compliant with Telcordia GR-253-CORE Issue 3 and ITU-T recommendation G-957 Power Supply Current ICC --- --- 140 mA Note 1 Data Input Current-Low IIL −350 --- --- µA Data Input Current-High IIH --- --- 350 µA Transmitter Data Input V oltage-High VIH − VCC −1.1 --- −0.74 V Note 2 Transmitter Data Input V oltage-Low VIL − VCC −2.0 --- −1.58 V Note 2 Transmitter Data Input Differential V oltage VDIFF 0.3 --- 1.6 V Note 2 Note 1: Not including the terminations. Note 2: These inputs are compatible with 10K, 10KH and 100K ECL and PECL input.

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 3/10 Date: 2003/02/17 http:// www.ritekom.com Receiver Electro-optical Characteristics (Vcc = 3.1 V to 3.5 V , TS3-0155-32S-P1: TA = 0 °C to 70 °C, TS3-0155-32S-P1-E: TA = −40 °C to 85°C) PARAMETER SYMBOL MIN TYP . MAX UNITS NOTE Data Rate B 50 155 200 Mb/s Optical Input Power-maximum PIN 0 --- --- dBm Note 1 Optical Input Power-minimum (Sensitivity) PIN --- --- −34 dBm Note 1 Operating Center Wavelength λC 1100 --- 1600 nm Signal Detect-Asserted PA --- --- −34 dBm Average Signal Detect-Deasserted PD −47 --- --- dBm Average Signal Detect-Hysteresis PA − PD 1.0 --- --- dB Signal Detect Assert Time TSD+ --- --- 100 µs Signal Detect Desssert Time TSD− --- --- 100 µs Signal Detect Output voltage-High VOH − VCC −1.1 --- −0.74 V Note 2 Signal Detect Output voltage-Low VOL − VCC −2.0 --- −1.58 V Note 2 Power Supply Current ICC --- --- 100 mA Note 3 Data Output Rise, Fall Time (10−90%) Tr, f --- 1 2 ns Data Output V oltage-High VOH − VCC −1.1 --- −0.74 V Note 2 Data Output V oltage-Low VOL − VCC −2.0 --- −1.58 V Note 2 Note 1: The input data is at 155.52 Mbps, 2 23−1 PRBS data pattern with 72 “1”s and 72 “0”s inserted per the ITU-T recommendation G .958 Appendix 1. The receiver is guaranteed to provide output data with Bit Error Rate (BER) better than or equal to 1×10 −10. Note 2: These outputs are compatible with 10K, 10KH and 100K ECL and PECL input. Note 3: The current exclude the output load current.

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 4/10 Date: 2003/02/17 http:// www.ritekom.com Block Diagram of Transceiver POST AMPLIFIER IC LASER DRIVER IC RRE- AMPLIFIER IC LASER DATA DATA/ DATA DATA/ ELECTRICAL SUBASSEMBLY OPTICAL SUB- ASSEMBLIES PIN PHOTODIODE DUPLEX SC RECEPTACLE SIGNAL DETECT TOP VIEW Transmitter Section The transmitter section consists of a 1310 nm InGaAsP laser in an eye safe optical subassembly (OSA) which mates to the fiber cable. The laser OSA is driven by a LD driver IC which converts differential input LVPECL logic signals into an analog laser driving current. Receiver Section The receiver utilizes an InGaAs PIN photodiode mounted together with a trans-impedance preamplifier IC in an OSA. This OSA is connected to a circuit providing post-amplification quantization, and optical signal detection. Receiver Signal Detect Signal Detect is a basic fiber failure indicator. This is a single-ended LVPECL output. As the input optical power is decreased, Signal Detect will switch from high to low (deassert point) somewhere between sensitivity and the no light input level. As the input optical power is increased from very low levels, Signal Detect will switch back from low to high (assert point). The assert level will be at least 1.0 dB higher than the deassert level.

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 5/10 Date: 2003/02/17 http:// www.ritekom.com Typical BER Performance of Receiver versus Input Optical Power Level 1.E-12 1.E-11 1.E-10 1.E-09 1.E-08 1.E-07 1.E-06 1.E-05 1.E-04 Relative Input Optical Power (dB) BER The figure shows the relationship between typical trade-off of BER and Relative Input Optical Power. Besides the required BER =1 × 10−10 of the ATM Forum 155.52 Mbps Physical Layer Standard, The transceiver can be operated at other Bit-Error-Rate conditions. The Relative Input Optical Power in dB is referenced to the actual sensitivity of the device. For BER conditions better than 1 × 10−10, more input signal is needed (+dB). Eye Diagram Transmitter Receiver Signal pattern: PRBS 23 Signal pattern: PRBS 23 Input Power: −35 dBm

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 6/10 Date: 2003/02/17 http:// www.ritekom.com Connection Diagram Pin-Out 1. RX GND 2. RD+ 3. RD− 4. SD 5. VCCR 6. VCCT 7. TD− 8. TD+ 9. TX GND TOP VIEW N/C N/C PIN SYMBOL DESCRIPTION 1 RX GND Receiver Signal Ground. Directly connect this pin to the receiver ground plane.

2 RD+

RD+ is an open-emitter output circuit. Terminate this high-speed differential LVPECL output with standard LVPECL techniques at the follow-on device input pin. (See recommended circuit schematic)

3 RD−

RD– is an open-emitter output circuit. Terminate this high-speed differential LVPECL output with standard LVPECL techniques at the follow-on device input pin. (See recommended circuit schematic) 4 SD Signal Detect. Normal optical input levels to the receiver result in a logic “1” output, VOH, asserted. Low input optical levels to the receiver result in a fault condition indicated by a logic “0” output VOL, deasserted Signal Detect is a single-ended LVPECL output. SD can be terminated with LVPECL techniques via 50 Ω to VCCR − 2 V. Alternatively, SD can be loaded with a 180 Ω resistor to RX GND to conserve electrical power with small compromise to signal quality. If Signal Detect output is not used, leave it open-circuited. This Signal Detect output can be used to drive a LVPECL input on an upstream circuit, such as, Signal Detect input or Loss of Signal-bar.

5 VCCR

Receiver Power Supply. Provide +3.3 Vdc via the recommended receiver power supply filter circuit. Locate the power supply filter circuit as close as possible to the V CCR pin.

6 VCCT

Transmitter Power Supply. Provide +3.3 Vdc via the recommended transmitter power supply filter circuit. Locate the power supply filter circuit as close as possible to the VCCT pin.

7 TD−

Transmitter Data In-Bar. Terminate this high-speed differential LVPECL input with standard LVPECL techniques at the transmitter input pin. (See recommended circuit schematic)

8 TD+

Transmitter Data In. Terminate this high-speed differential LVPECL input with standard LVPECL techniques at the transmitter input pin. (See recommended circuit schematic)

9 TX GND

Transmitter Signal Ground. Directly connect this pin to the transmitter signal ground plane. Directly connect this pin to the transmitter ground plane.

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 7/10 Date: 2003/02/17 http:// www.ritekom.com Recommended Circuit Schematic DC/DC Coupling RX GND RD+ RD− SD V TD− TD+ TX GND VCC RiteKom Transceiver TD+ TD− VCC R10 R9 RD+ RD− Laser Driver LIMITING Amplifier Signal detect Pre- Amp CCR CCTV ECL/PECL DRIVER Serializer/ Deserializer Receiver PLL etc. R6 R5 C1/C2/C4 = 0.1 µF C3 = 4.7 µF L1/L2 = 1 µH R1/R3/R5/R7/R9 = 130 Ω R2/R4/R6/R8/R10 = 82 Ω In order to get proper functionality, a recommended circuit is provided in above recommended circuit schematic. When designing the circuit interface, there are a few fundamental guidelines to follow. (1) The differential data lines should be treated as 50 Ω Micro strip or strip line transmission lines. This will help to minimize the parasitic inductance and capacitance effects. Locate termination at the received signal end of the transmission line. The length of these lines should be kept short and of equal length. (2) For the high speed signal lines, differential signals should be used, not single-ended signals, and these differential sign als need to be loaded symmetrically to prevent unbalanced currents which will cause distortion in the signal. (3) Multi layer plane PCB is best for distribution of VCC, returning ground currents, forming transmission lines and shielding, Also, it is important to suppress noise from influencing the fiber-optic transceiver performance, especially the receiver circuit. (4) A separate proper power supply filter circuits shown in Figure for the transmitter and receiver sections. These filter circuits suppress Vcc noise over a broad frequency range, this prevents receiver sensitivity degradation due to VCC noise. (5) Surface-mount components are recommended. Use ceramic bypass capacitors for the 0.1 µF capacitors and a surface-mount coil inductor for 1 µH inductor. Ferrite beads can be used to replace the coil inductors when using quieter VCC supplies, but a coil inductor is recommended over a ferrite bead. All power supply components need to be placed physically next to the VCC pins of the receiver and transmitter. (6) Use a good, uniform ground plane with a minimum number of holes to provide a low-inductance ground current return for the power supply currents.

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 8/10 Date: 2003/02/17 http:// www.ritekom.com Recommended Board Layout Hole Pattern Unit : mm(inches) This transceiver is compatible with industry standard wave or hand solder processes. After wash process, all moisture must be completely remove from the module. The transceiver is supplied with a process plug to prevent contamination during wave solder and aqueous rinse as well as during handling, shipping or storage. Solder fluxes should be water-soluble, organic solder fluxes. Recommended cleaning and degreasing chemicals for these transceivers are alcohol’s (methyl, isopropyl, isobutyl), aliphatics (hexane, heptane) and other chemicals, such as soap solution or naphtha. Do not use partially halogenated hydrocarbons for cleaning/degreasing.

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 9/10 Date: 2003/02/17 http:// www.ritekom.com Drawing Dimensions Unit : mm

1310 nm Single-mode Transceiver (S1.1) 1x9, SC Duplex Connector, 3.3 V Headquarters : No. 669, Sec. 4 Chung Hsing Road Chudung, HsinChu, Taiwan 310, ROC Tel: +886-3-582-8270 Fax: +886-3-582-8416 V e r s i o n 3 . 3 10/10 Date: 2003/02/17 http:// www.ritekom.com Regulatory Compliance FEATURE TEST METHOD PERFORMANCE Electrostatic discharge (ESD) to the electrical pins MIL-STD-883D Method 3015.7 Class 1(>1 kV) – Human Body Model Electromagnetic interference (EMI) FCC Class B EN55022 Class B The transceiver is mounded on a circuit card without a chassis enclosure at frequencies up to 1000 MHz. Margins will be dependent on customer’s board and chassis designs. Immunity Variation of IEC801-3 Typically show no measurable effect from a 10 V/m filed swept from 30 MHz to 1000 MHz applied to the transceiver without a chassis enclosure. FDA 21 CFR 1040.10 and 1040.11 Class 1 FDA Accession Number: 0012715-01 Eye safety EN 60825-1:1994+A11 EN 60950: 1992+A1+A2+A3+A4+A11 EN 60825-2: 1994+A1 TUV certificated Number: R 3-50005227 Eye Safety Mark The TS3 series Single-mode transceiver is a class 1 laser product. It complies with EN 60825-1 and FDA 21 CFR 1040.10 and 1040.11. In order to meet laser safety requirements the transceiver shall be operated within the Absolute Maximum Ratings. Caution All adjustments have been done at the factory before the shipment of the devices. No maintenance and user serviceable part is required. Tampering with and modifying the performance of the device will result in voided product warranty. Required Mark Laser Emission Indication of Laser Aperture and Beam Note : All information contained in this document is subject to change without notice. Class 1 Laser Product Complies with 21 CFR 1040.10 and 1040.11