TRB2G1CB1C00000

TRB2G1CB1C00000 OPLINK | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Features

RevC.2008.04.01 Parameter Symbol Minimum Maximum Units Storage Temperature TST - 40 + 85 °C Operating Case Temperature1 Commercial TOP - 5 + 70 Industrial - 40 + 85 Supply Voltage VCC 0 + 4.5 V Input Voltage VIN 0 VCC V 1 Measured on top side of SFP module at the front center vent hole of the cage. Absolute Maximum Ratings Pb

Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 stan- dards. They must be operated under specified operating conditions. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements Oplink Communications, Inc. Transmitter Performance Characteristics TRPBG1LX (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units Operating Data Rate 1 B - 1250 - Mb/s Optical Output Power 2 PO - 9.0 - - 3.0 dBm Center Wavelength BX10-U 1310nm FP λC 1260 1310 1360 nm BX10-D 1490nm DFB 1480 1490 1500 Spectral Width (RMS) BX10-U 1260 - 1280nm ΔλRMS - - 2.09 nm 1281 - 1360nm - - 2.58 Spectral Width (-20dB) BX10-U 1480 - 1500nm Δλ20 - - 0.88 dB Extinction Ratio Phi /Plo 6 - - dB Optical Modulation Amplitude OMA - 8.2 - - dBm Transmitter OFF Output Power - - - - 45 dBm Relative Intensity Noise RIN 12OMA - - - 113 dB/Hz Optical Return Loss Tolerance ORLT - - 12 dB Transmitter Reflectance TR - - - 12 dB Deterministic Jitter DJ - - 80 ps Total Jitter TJ - - 227 ps Transmitter Output Eye Compliant with Eye Mask Defined in IEEE 802.3ah Standard 1 Data rate ranges from 125Mb/s to 1300Mb/s. However, some degradation may be incurred in overall performance. 2 Measured average power coupled into single mode fiber. Receiver Performance Characteristics Parameter Symbol Minimum Typical Maximum Units Operating Data Rate 1 B - 1250 - Mb/s Minimum Input Optical Power (10-12 BER) 2 Pmin - 20.0 - 22.0 - dBm Maximum Input Optical Power (10 -10 BER) 2 Pmax - 3.0 - - dBm Sensitivity as OMA 3 OMA - 18.7 - - dBm LOS Thresholds Increasing Light Input Plos+ - - - 20.0 dBm Decreasing Light Input Plos- - 30.0 - - LOS Hysteresis 2 - 0.5 - - dB Stressed Sensitivity - - 15.4 - - dBm Stressed Sensitivity as OMA - - 14.6 - - dBm Vertical Eye-Closure Penalty - 2.6 - - dB Deterministic Jitter DJ - - 170 ps Total Jitter TJ - - 266 ps Wavelength of Operation BX10-D λ 1260 - 1360 nm BX10-U 1480 - 1560 Receiver Reflectance - - - - 12 dB Electrical 3dB Upper Cutoff Frequency - - - 1500 MHz 1 Data rate ranges from 125Mb/s to 1300Mb/s. However, some degradation may be incurred in overall performance. 2 Measured at 1250Mb/s with 27-1 PRBS and 1310nm & 1490nm wavelengths. 3 Specified with minimum extinction ratio of 6dB. (Over Operating Case Temperature. VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate All parameters guaranteed only at typical data rate 2 RevC.2008.04.01

Oplink Communications, Inc. Electrical Pad Layout Host Board Connector Pad Layout Toward Bezel Toward ASIC TX GND TD- (TX DATA IN-) TD+ (TX DATA IN+) TX GND VccTX VccRX RX GND RD+ (RX DATA OUT+) RD- (RX DATA OUT-) RX GND Top of Board TX GND TX Fault TX Disable MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) NO CONNECTION LOS RX GND RX GND Bottom of Board (as viewed thru top of board) Transmitter Performance Characteristics TRPBG1LX (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units Input Voltage Swing (TD+ & TD-) 1 VPP-DIF 0.25 - 2.4 V Input HIGH Voltage (TX Disable) 2 VIH 2.0 - VCC V Input LOW Voltage (TX Disable) 2 VIL 0 - 0.8 V Output HIGH Voltage (TX Fault) 3 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (TX Fault) 3 VOL 0 - 0.8 V 1 Differential peak-to-peak voltage. 2 There is an internal 4.7 to 10kΩ pull-up resistor to VccT. 3 Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Receiver Electrical Interface Electrical Power Supply Characteristics (Over Operating Case Temperature. VCC = 3.13 to 3.47V)) Parameter Symbol Minimum Typical Maximum Units Supply Voltage VCC 3.13 3.3 3.47 V Supply Current Commercial ICC - 175 245 mA Industrial - 175 285 Parameter Symbol Minimum Typical Maximum Units Output Voltage Swing (RD+ & RD-) 1 VPP-DIF 0.6 - 2.0 V Output HIGH Voltage (LOS) 2 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (LOS)) 2 VOL 0 - 0.5 V 1 Differential peak-to-peak voltage across external 100Ω load. 2 Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). (Over Operating Case Temperature. VCC = 3.13 to 3.47V)) Module Definition MOD_DEF(0) pin 6 MOD_DEF(1) pin 5 MOD_DEF(2) pin 4 Interpretation by Host TTL LOW SCL SDA Serial module definition protocol RevC.2008.04.013

Oplink Communications, Inc. Application Notes Electrical interface: All signal interfaces are compliant with the SFP MSA specification. The high speed DATA interface is differential AC-coupled internally with 0.1μF and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7 - 10kΩ resistor on the host board Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates a logic HIGH when an insufficient photocurrent is produced. TX_Fault: The output indicates LOW when the transmitter is operating normally, and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output that should be pulled up with a 4.7 - 10kΩ resistor on the host board. TX Fault is latched per SFP MSA. TX_Disable: When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled (less than -45dBm). Serial Identification and Monitoring: The module definition of SFP is indicated by the three module definition pins, MOD_DEF(0), MOD_DEF(1) and MOD_DEF(2). Upon power up, MOD_DEF(1:2) appear as NC (no connection), and MOD_DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I 2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the SFP that are not write protected, and the negative edge clocks data from the SFP . The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the startand end of serial protocol activation. The supported monitoring functions are internal temperature, supply voltage, bias current, transmitter power, average receiver signal, all alarms and warnings and software monitoring of TX Fault/LOS. The device is internally calibrated. The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA, and SFF-8472, Rev. 9.4 Power supply and grounding: The power supply line should be well-filtered. All 0.1μF power supply bypass capacitors should be as close to the transceiver module as possible. Example of SFP host board schematic TRPBG1LX RevC.2008.04.01 R: 4.7 to 10kΩ TRPBG1LX

Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Commu- nications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. © 2006, Oplink Communications, Inc. 46335 Landing Pkwy Fremont, CA 94538 T el: (510) 933-7200 Fax: (510) 933-7300 Email: Sales@Oplink.com • www.oplink.com Mechanical Package

Ordering Information

Dimensions in inches [mm] Defaultt olerances: TRPBG1LX Model Name Temperature Range Latch Color Typical Wavelength Distance Oplink Order Number Reference OCP P/N Tx Rx TRB2G1CB1C00000 TRPBG1LXDBBSH - 5 °C to + 70°C Blue 1310nm 1490nm 10km TRB2G1CB2C00000 TRPBG1LXDBVS2 - 10 °C to + 85°C Violet 1490nm 1310nm 10km TRB2G1CB1I00000 TRPBG1LXDABSH - 40 °C to + 85°C Blue 1310nm 1490nm 10km TRB2G1CB2I00000 TRPBG1LXDAVS2 - 40 °C to + 85°C Violet 1490nm 1310nm 10km RevC. 2008.04.015