DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
Features
Transmission distance up to 10km (SM fiber) Low power consumption Wide case operating temperature range Compliant to SFP+ Electrical MSA SFF-8431 Compliant to SFP+ Mechanical MSA SFF-8432 Compliant to 10GBASE-L specifications Digital Diagnostics Monitoring (DDM) through Serial Interface compliant with SFF-8472, Rev. 10.4 RoHS 6/6 Compliant Laser Class 1 IEC/CDRH Compliant TPP5XGFLRx000E2A Parameter Symbol Minimum Maximum Units Storage Temperature Range TST - 40 + 85 °C Case Operating Temperature 1 “Commercial” TOP - 5 + 70 °C“Extended” “Industrial” - 5 - 40 + 85 + 85 Operating Relative Humidity 2 RH 0 85 % Supply Voltage Range VCC - 0.5 + 3.6 V 1 Measured on top side of SFP+ module at the front center vent hole of the cage.
2 Non condensing
1310nm 10km SFP+ Transceivers
Oplink Communications, LLC S0514 Rev.01. (web) 2016-01-082 (Over Operating Case Temperature. VCC = 3.13 to 3.47V)Receiver Performance Characteristics Transmitter Performance Characteristics (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Laser Safety: All transceivers are Class 1 Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, LLC. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class 1 Laser Safety Requirements Note: The specified characteristics are met within the recommended range of operation. Unless otherwise noted typical data are quoted at nominal voltage and +25°C ambient temperature. Parameter Symbol Minimum Typical Maximum Units Data Rate B - 10.3125 - Gb/s Center Wavelength λC 1260 1310 1355 nm Spectral Width Δλ20 - - 1.0 nm Average Optical Output Power 1 PAvg - 8.2 - + 0.5 dBm Optical Modulation Amplitude POMA - 5.2 - - dBm Extinction Ratio ER 3.5 - - dB Relative Intensity Noise RIN - - - 128 dB/Hz Side Mode Suppression Ratio SMSR 30 - - dB Optical Return Loss Tolerance - - - - 12 dB Transmitter and Dispersion Penalty @ 10.3125Gb/s TDP - - 3.2 dB Average Launch Power of OFF transmitter P OFF - - - 30 dB Optical Output Eye Compliant with IEEE 802.3ae 1 Average power figures are informative only, per IEEE 802.3ae Parameter Symbol Minimum Typical Maximum Units Data Rate B - 10.3125 - Gb/s Wavelength of Operation λ 1260 - 1355 nm Receiver Sensitivity Pavg @ 10.3125 Gb/s 1 Pmin - - - 14.4 dBm OMA @ 10.3125 Gb/s 1 - - - 12.6 Stressed Receiver Sensitivity in OMA Maximum Input Power Pmax + 0.5 - - dBm Receiver Reflectance - - - - 12 dB LOS Hysteresis - 0.5 - - dB LOS Thresholds Increasing Light Input Plos+ - 30 - - dBm Decreasing Light Input Plos- - - - 16 1 Specified with BER <1x10-12 and PRBS 2 31-1. 2 Comply with IEEE 802.3ae
Oplink Communications, LLC TPP5XGFLRx000E2A S0514 Rev.01. (web) 2016-01-083 VEET TD+ TD- VEET VCCT VCCR VEER RD+ RD- VEER VEER RS1 RX_LOS RS0 MOD-ABS SCL SDA TX_DISABLE TX_FAULT VEET TOWARD HOST TOWARD BEZEL (Over Operating Case Temperature. VCC = 3.13 to 3.47V) (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Electrical Power Supply Characteristics Receiver Electrical Characteristics Transmitter Electrical Characteristics (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Connector Pin-out Parameter Symbol Minimum Typical Maximum Units Power Supply Voltage VCC 3.13 3.30 3.47 V DC Common Mode Voltage VCM 0 - 3.60 V Supply Current IVCC - - 300 mA Maximum Sustained Peak Current - - - 400 mA Power Consumption PW - - 1 W Parameter Symbol Minimum Typical Maximum Units Differential Output Impedance Zd - 100 - Ω Differential Output Swing VPP-DIFF 300 - 850 mV Output Rise and Fall time (20% to 80%) tRH, tFH 24 - - ps Output HIGH Voltage (LOS) 1 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (LOS) 1 VOL 0 - 0.8 V 1 Open collector compatible, 4.7kΩ to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Parameter Symbol Minimum Typical Maximum Units Differential Input Impedance Z d - 100 - Ω Differential Input Voltage Swing VPP-DIFF 180 - 700 mV Input HIGH Voltage (TX Disable) 1 VIH 2.0 - VCC V Input LOW Voltage (TX Disable) 1 VIL 0 - 0.8 V Output HIGH Voltage (TX Fault) 2 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (TX Fault) 2 VOL 0 - 0.8 V 1 There is an internal 4.7kΩ to 10kΩ pull-up resistor to VccT. 2 Open collector compatible, 4.7kΩ to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Note: The specified characteristics are met within the recommended range of operation. Unless otherwise noted typical data are quoted at nominal voltage and +25°C ambient temperature.
4 S0514 Rev.01. (web) 2016-01-08Oplink Communications, LLC TPP5XGFLRx000E2A Application Notes Electrical Pin Description Electrical Interface: All signal interfaces are compliant with the SFP+ MSA specification. The high speed DATA interface is differential AC-coupled internally and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7 – 10 kΩ resistor on the host board. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates logic HIGH when an insufficient photocurrent is produced. TX_Fault: The output indicates LOW when the transmitter is operating normally and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output and should be pulled up with a 4.7 – 10 kΩ resistor on the host board. TX_Disable: : When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled. The laser is also disabled if this line is left floating, as it is pulled high inside the transceiver. Serial Identification and Monitoring: The module definition of SFP is indicated by the MOD_ABS pin and the 2-wrie serial interface. Upon power up, the 2-wrie interface appears as NC (no connection), and MOD_ABS is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I 2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the device that are not write protected, and the negative edge clocks data from the device. The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The supported monitoring functions are temperature, voltage, bias current, transmitter power, average receiver signal, all alarms and warnings, and software monitoring of TX Fault/LOS. The device is internally calibrated. The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA, and SFF-8472, Rev. 10.4. Power Supply and Grounding: The power supply line should be well-filtered. All power supply bypass capacitors should be as close to the transceiver module as possible. Pin Logic Symbol Description 1 - VeeT Module Transmitter Ground
2 LVTTL-O TX_Fault Module Transmitter Fault
3 LVTTL-I TX_Disable Transmitter Disable; Turns off transmitter laser output
4 LVTTL-I/O SDA 2-Wire Serial Interface Data Line
5 LVTTL-I/O SCL 2-Wire Serial Interface Clock
6 - MOD-ABS Module Definition, Grounded in the module
7 LVTTL-I RS0 No function implemented
8 LVTTL-O RX_LOS Receiver Loss of Signal Indication
9 LVTTL-I RS1 No function implemented
10 - VeeR Module Receiver Ground 11 - VeeR Module Receiver Ground
12 CML-O RD- Receiver Inverted Data Output
13 CML-O RD+ Receiver Non-Inverted Data Output
14 - VeeR Module Receiver Ground 15 - VccR Module Receiver 3.3V Supply 16 - VccT Module Transmitter 3.3V Supply 17 - VeeT Module Transmitter Ground
18 CML-I TD+ Transmitter Non-Inverted Data Input
19 CML-I TD- Transmitter Inverted Data Input
20 - VeeT Module Transmitter Ground
Oplink Communications, LLC S0514 Rev.01. (web) 2016-01-085 TPP5XGFLRx000E2A 50/uni03A9 line 50/uni03A9 line 50/uni03A9 line 50/uni03A9 line TD+ TD- RD+ RD- ASIC/ SerDes 4.7µH 0.1µF 22µF 0.1µF +3.3V +3.3V +3.3V SCL, SDA, MOD_ABS TX_Fault +3.3VR R R SFP+ VccR RX_LOS 4.7µH 0.1µF 22µF 0.1µF +3.3V VccT VeeT, VeeR R: 4.7k/uni03A9 to 10k/uni03A9 Interfacing the Transceivers ESD & Electromagnetic Compatibility Application Schematics Recommended electrical connections to transceiver are shown below. Communication is via a serial 2-wire serial interface. As described in the document SFF-8472 (REV. 10.4) there are two distinct address spaces: Requirements Standard Status Electro Static Discharge to the Electrical Pins (ESD) EIA/JESD22-A114-B MIL-STD 883C Method 3015.7 Exceeds requirements Class 1B (>1000V) Immunity to ESD (housing, receptacle) IEN 61000-4-2 Exceeds requirements Discharges ranging from 2kV to 15kV without damages to the transceiver Electromagnetic Emission (EMI) FCC Part 15, Class B EN 55022 Class B CISPR 22 Exceeds requirements Class B Base Address A0(hex) Byte Address Content 0 – 95 Serial Transceiver ID as defined in SFP MSA 96 – 127 OPLINK Specific 128 – 255 Reserved Base Address A2(hex) Byte Address Content 0 - 55 Alarm & Warnings thresholds & limits 56 - 95 External calibration constants (not used) 96 – 119 Values from real time diagnostic monitoring 120 – 127 Not used 128 – 247 Customer specific, writable area 248 - 255 Not used
S0514 Rev.01. (web) 2016-01-086 46335 Landing Pkwy Fremont, CA 94538 T el: (510) 933-7200 Fax: (510) 933-7300 Email: Sales@Oplink.com • www.oplink.com TPP5XGFLRx000E2A Oplink Communications, LLC. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Com- munications, LLC. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, LLC. for its use nor for any infringe- ments of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, LLC. © 2015, Oplink Communications, LLC. Model Name Operating Temperature Nominal Wavelength Distance Latch Color TPP5XGFLRC000E2A - 5°C to +70°C 1310nm 10km Blue TPP5XGFLRE000E2A - 5°C to +85°C 1310nm 10km Blue TPP5XGFLRI000E2A - 40°C to + 85°C 1310nm 10km Blue
Ordering Information
Dimensions in [inches] mm Millimeters are the primary units. Tolerances are in accordance with SFF-8432 Rev.5