DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

Parameter Symbol Minimum Maximum Units Storage Temperature Range TST - 40 + 85 °C Operating Case Temperature 1 “Commercial” TOP - 5 + 70 °C“Extended” - 5 + 85 “Industrial” - 40 + 85 Operating Relative Humidity 2 RH 0 85 % Supply Voltage Range VCC - 0.5 + 3.6 V 1 Measured on top side of SFP+ module at the front center vent hole of the cage.

2 Non condensing

CWDM 40km SFP+ Transceivers  Temperature-stablized CWDM EML transmitter  Multi-rate for Ethernet & Fiber Channel  Transmission distance up to 40km (SM Fiber)  Low power consumption  Wide case operating temperature range  Compliant with SFP+ Electrical MSA SFF-8431  Compliant with SFP+ Mechanical MSA SFF-8432  Compliant with 10GBASE-E specifications  Digital Diagnostics Monitoring (DDM) through Serial Interface comply with SFF-8472, Rev. 10.4  RoHS 6/6 Compliant  Laser Class 1 IEC/CDRH compliant The TPC1XGJERxG is an enhanced small form factor pluggable (SFP+) fiber optic transceiver with digital diagnostics monitoring functionality (DDM). Supporting Ethernet and Fiber Channel standards makes it ideally suited for high capacity data-com and storage area network applications. DDM functionality (alarm and warning features) is integrated into the design via an I2C serial interface per the Multi-Source Agreement (MSA) SFF-8472, Rev. 10.4. Each transceiver utilizes an electro absorption modulator integrated laser (EML) with an operating wavelength with 100GHz (0.8nm) spacing per the ITU-grid. The transceiver supports data rates ranging from 11.3Gbps down to 8Gbps. It provides an excellent solution for data transmission at CWDM wavelength over up to 40km single mode fiber. The low power consumption and excellent EMI performance enable system design with high port density. The product is RoHS compliant and is designed and tested in accordance with industry safety standards. The transceiver is Class I Laser product per U.S. FDA/CDRH and international IEC-60825 standards. The TPC1XGJERxG transceiver connects to standard 20-pad SFP+ connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different transceivers without removing the power supply from the host system. The transmitter and receiver DATA interfaces are internally AC-coupled. LV-TTL Transmitter Disable control input and Loss of Signal (LOS) output interfaces are also provided. The transceiver has bail-type latch, which offers an easy and convenient way to release the modules. The transceiver operates from a single +3.3V power supply over an operating case temperature range of -5°C to +70°C (Commercial), or -5°C to +85°C (Extended) or -40°C to +85°C (Industrial).

2Oplink Communications, Inc S0218. Rev.03 (web) 2014-02-24 Laser Safety: All transceivers are Class 1 Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. This product complies with 21 CFR 1040.10 and 1040.11 Meets Class 1 Laser Safety Requirements (Over Operating Case Temperature. VCC = 3.13 to 3.47V)Receiver Performance Characteristics Transmitter Performance Characteristics Parameter Symbol Minimum Typical Maximum Units Data Rate B 8.0 - 11.3 Gb/s Center Wavelength λC See Ordering Information Table nm Center Wavelength Tolerance - - 6.5 - + 6.5 nm Spectral Width (-20dB) Δλ 20 - - 1.0 nm Average Optical Output Power 1 PAvg - 1 - + 4 dBm Extinction Ratio ER 4.5 - - dB Relative Intensity Noise in OMA RIN21OMA - - - 128 dB/Hz Side Mode Suppression Ratio SMSR 30 - - dB Optical Return Loss Tolerance - - - - 21 dB Transmitter and Dispersion Penalty @ 10.3125Gb/s TDP - - 3 dB Optical Output Eye Compliant with IEEE 802.3ae 1 Average power figures are informative only, per IEEE 802.3ae. Parameter Symbol Minimum Typical Maximum Units Data Rate B 8.0 - 11.3 Gb/s Wavelength of Operation λ 1450 - 1620 nm Receiver Sensitivity @ 10.3125Gb/s 1 Pmin - - - 14.0 dBm Maximum Input Power (10 -12 BER) Pmax - 1 - - dBm Receiver Reflectance - - - - 26 dB LOS Hysteresis - 0.5 - - dB LOS Thresholds Increasing Light Input Plos+ - - - 16 dBm Decreasing Light Input Plos- - 30 - - 1 Specified with BER <1x10-12 and PRBS 2 31-1. Note: The specified characteristics are met within the recommended range of operation. Unless otherwise noted typical data are quoted at nominal voltage and +25°C ambient temperature. (Over Operating Case Temperature. VCC = 3.13 to 3.47V)

Oplink Communications, Inc S0218. Rev.03 (web) 2014-02-24 (Over Operating Case Temperature. VCC = 3.13 to 3.47V)Transmitter Electrical Characteristics Connector Pin-out (Over Operating Case Temperature. VCC = 3.13 to 3.47V) (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Electrical Power Supply Characteristics Receiver Electrical Interface VEET TD+ TD- VEET VCCT VCCR VEER RD+ RD- VEER VEER RS1 RX_LOS RS0 MOD-ABS SCL SDA TX_DISABLE TX_FAULT VEET TOWARD HOST TOWARD BEZEL Parameter Symbol Minimum Typical Maximum Units Power Supply Voltage VCC 3.13 3.30 3.47 V DC Common Mode Voltage VCM 0 - 3.60 V Supply Current I VCC - 310 - mA Power Consumption PW - 1.0 - W Parameter Symbol Minimum Typical Maximum Units Differential Output Impedance Zd - 100 - Ω Differential Output Swing VPP-DIFF 300 450 850 mV Output Rise and Fall time (20% to 80%) tRH, tFH 28 - - ps Output HIGH Voltage (LOS) 1 VOH VCC - 1.3 - VCC + 0.3 V Output LOW Voltage (LOS) 1 VOL 0 - 0.8 V 1 Open collector compatible, 4.7kΩ to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Parameter Symbol Minimum Typical Maximum Units Differential Input Impedance Z d - 100 - Ω Differential Input Voltage Swing VPP-DIFF 180 - 700 mV Input HIGH Voltage (TX Disable) 1 VIH 2.0 - VCC V Input LOW Voltage (TX Disable) 1 VIL 0 - 0.8 V Output HIGH Voltage (TX Fault) 2 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (TX Fault) 2 VOL 0 - 0.8 V 1 There is an internal 4.7kΩ to 10kΩ pull-up resistor to VccT. 2 Open collector compatible, 4.7kΩ to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Note: The specified characteristics are met within the recommended range of operation. Unless otherwise noted typical data are quoted at nominal voltage and +25°C ambient temperature.

Oplink Communications, Inc S0218. Rev.03 (web) 2014-02-24 Application Notes Module Pin Description 2-wrie serial interface. Upon power up, the 2-wrie interface appears as NC (no connection), and MOD_ABS is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I 2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the device that are not write protected, and the negative edge clocks data from the device. The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The supported monitoring functions are temperature, voltage, bias current, transmitter power, average receiver signal, all alarms and warnings, and software monitoring of TX Fault/LOS. The device is internally calibrated. The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA, and SFF-8472, Rev. 10.4. Power Supply and Grounding: The power supply line should be well-filtered. All power supply bypass capacitors should be as close to the transceiver module as possible. Electrical Interface: All signal interfaces are compliant with the SFP+ MSA specification. The high speed DATA interface is differential AC-coupled internally and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7kΩ - 10kΩ resistor on the host board. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates logic HIGH when an insufficient photocurrent is produced. TX_Fault: The output indicates LOW when the transmitter is operating normally and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output and should be pulled up with a 4.7kΩ - 10kΩ resistor on the host board. TX_Disable: When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled. The laser is also disabled if this line is left floating, as it is pulled high inside the transceiver. Serial Identification and Monitoring: The module definition of SFP is indicated by the MOD_ABS pin and the Pin Logic Symbol Description 1 - VeeT Module Transmitter Ground

2 LVTTL-O TX_Fault Module Transmitter Fault

3 LVTTL-I TX_Disable Transmitter Disable; Turns off transmitter laser output

4 LVTTL-I/O SDA 2-Wire Serial Interface Data Line

5 LVTTL-I/O SCL 2-Wire Serial Interface Clock

6 - MOD-ABS Module Definition, Grounded in the module

7 LVTTL-I RS0 No function implemented

8 LV T TL-O RX_LOS Receiver Loss of Signal Indication

9 LVTTL-I RS1 No function implemented

10 - VeeR Module Receiver Ground 11 - VeeR Module Receiver Ground

12 CML-O RD- Receiver Inverted Data Output

13 CML-O RD+ Receiver Data Output

14 - VeeR Module Receiver Ground 15 - VccR Module Receiver 3.3V Supply 16 - VccT Module Transmitter 3.3V Supply 17 - VeeT Module Transmitter Ground

18 CML-I TD+ Transmitter Non-Inverted Data Input

19 CML-I TD- Transmitter Inverted Data Input

20 - VeeT Module Transmitter Ground

Oplink Communications, Inc S0218. Rev.03 (web) 2014-02-24 50/uni03A9 line 50/uni03A9 line 50/uni03A9 line 50/uni03A9 line TD+ TD- RD+ RD- ASIC/ SerDes 4.7µH 0.1µF 22µF 0.1µF +3.3V +3.3V +3.3V SCL, SDA, MOD_ABS TX_Fault +3.3VR R R SFP+ VccR RX_LOS 4.7µH 0.1µF 22µF 0.1µF +3.3V VccT VeeT, VeeR R: 4.7k/uni03A9 to 10k/uni03A9 ESD & Electromagnetic Compatibility Communication is via a serial 2-wire serial interface. As described in the document SFF-8472 (REV. 10.4) there are two distinct address spaces: Interfacing the Transceivers Recommended electrical connections to transceiver are shown below.Application Schematics Requirements Standard Status Electro Static Discharge to the Electrical Pins (ESD) EIA/JESD22-A114-B MIL-STD 883C Method 3015.7 Exceeds requirements Class 1B (>1000V) Immunity to ESD (housing, receptacle) IEN 61000-4-2 Exceeds requirements Discharges ranging from 2kV to 15kV without damages to the transceiver Electromagnetic Emission (EMI) FCC Part 15, Class B EN 55022 Class B CISPR 22 Exceeds requirements Class B Base Address A0(hex) Byte Address Content 0 – 95 Serial Transceiver ID as defined in SFP MSA 96 – 127 OPLINK Specific 128 – 255 Reserved Base Address A2(hex) Byte Address Content 0 - 55 Alarm & Warnings thresholds & limits 56 - 95 External calibration constants (not used) 96 – 119 Values from real time diagnostic monitoring 120 – 127 Not used 128 – 247 Customer specific, writable area 248 - 255 Not used

Oplink Communications, Inc S0218. Rev.03 (web) 2014-02-24 Package Outline

Ordering Information

Oplink can provide a remarkable range of customized optical solutions. For detail, please contact Oplink’s Sales and Marketing for your requirements and ordering information (5 1 0) 933-7200 or Sales@oplink.com. Dimensions in [inches] mm Millimeters are the primary units. Tolerances are in accordance with SFF-8432 Rev.5 Model Name Operating Temperature Center Wavelength Distance TPC1XGJERC00010G - 5°C to +70°C Commercial 1471nm 40km TPC1XGJERC00020G - 5°C to +70°C Commercial 1491nm 40km TPC1XGJERC00030G - 5°C to +70°C Commercial 1511nm 40km TPC1XGJERC00040G - 5°C to +70°C Commercial 1531nm 40km TPC1XGJERC00050G - 5°C to +70°C Commercial 1551nm 40km TPC1XGJERC00060G - 5°C to +70°C Commercial 1571nm 40km TPC1XGJERC00070G - 5°C to +70°C Commercial 1591nm 40km TPC1XGJERC00080G - 5°C to +70°C Commercial 1611nm 40km

46335 Landing Pkwy Fremont, CA 94538 T el: (510) 933-7200 Fax: (510) 933-7300 Email: Sales@Oplink.com • www.oplink.com TPC1XGJERxG S0218. Rev.03 (web) 2014-02-24 Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Com- munications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringe- ments of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. © 2014, Oplink Communications, Inc. Model Name Operating Temperature Center Wavelength Distance TPC1XGJERE00010G - 5°C to +85°C Extended 1471nm 40km TPC1XGJERE00020G - 5°C to +85°C Extended 1491nm 40km TPC1XGJERE00030G - 5°C to +85°C Extended 1511nm 40km TPC1XGJERE00040G - 5°C to +85°C Extended 1531nm 40km TPC1XGJERE00050G - 5°C to +85°C Extended 1551nm 40km TPC1XGJERE00060G - 5°C to +85°C Extended 1571nm 40km TPC1XGJERE00070G - 5°C to +85°C Extended 1591nm 40km TPC1XGJERE00080G - 5°C to +85°C Extended 1611nm 40km TPC1XGJERI00010G - 40°C to +85°C Industrial 1471nm 40km TPC1XGJERI00020G - 40°C to +85°C Industrial 1491nm 40km TPC1XGJERI00030G - 40°C to +85°C Industrial 1511nm 40km TPC1XGJERI00040G - 40°C to +85°C Industrial 1531nm 40km TPC1XGJERI00050G - 40°C to +85°C Industrial 1551nm 40km TPC1XGJERI00060G - 40°C to +85°C Industrial 1571nm 40km TPC1XGJERI00070G - 40°C to +85°C Industrial 1591nm 40km TPC1XGJERI00080G - 40°C to +85°C Industrial 1611nm 40km