TPAC200 TOTAL-POWER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
UNIVERSAL AC INPUT HARMONIC CORRECTION AC-DC HOT-SWAP CompactPCI QUAD OUTPUT 200 WATTS ACTIVE CURRENT SHARING SWITCHING POWER SUPPLIES TPAC200P SERIES GENERAL SPECIFICATION Efficiency: Typ. 76-79 %. Switching Frequency: 130K Hz. Circuit Topology: Forward circuit. Transient Response: Peak transient less than 100mV and recovers within 3mS after 25% load-change. Safety Standard: IEC60950 Class I. Construction: Eurocard 3U X 8HP X 160mm CompactPCI format. Front Panel with either Ordinary handle or Extractor handle. Operating Temperature: 0 to +50 °C at full load with specified air flow. Derates linearly to 50% at +70°C. Storage Temperature: -40 to +85 °C. Temperature Coefficient: Typ. ±0.02% / °C. Cooling: At least 20cfm (600 lfm) moving air is required to achieve full rating power 200W in a confined area. Power Density: 3.73 Watts/ Cubic Inch. Remark: All measurements are at nominal input, full load and +25°C unless otherwise specifications. FEATURES: 200W 3U X 8HP EUROCARD PACKAGE MEET IEC1000-3-2 HARMONIC CORRECTION INTERNAL OR-ING DIODES FOR N+1 REDUNDANCY HOT-SWAPPABLE THIRD-WIRE CURRENT SHARING EMI MEET EN 55022 / FCC CLASS A CE MARKING COMPLIANCE FULLY COMPLIANT WITH PICMG SPECIFICATION INPUT SPECIFICATION Input Voltage: Typ. 90-264Vac. Power Factor Correction: Meet Harmonic Correction Input Connector: Positronic 47-pin PCIH47M400A1. Input Frequency: 47-63Hz. Inrush Current: Less than 30.6A @ 230Vac. Input Current: 2.3A @115Vac/1.2A @230Vac. Dielectric Withstand: Meet IEC950 regulation. EMI: Meet EN55022 / FCC Class A. Hold-up Time: 10mS after power fail signal. Turn-on Delay/Rise Time: 1 Sec./20 mS. Earth Leakage: Less than 0.5mA @230Vac. Remote ON/OFF: Available at [INH#] & [EN#] pins. Power Fail Signal: Available at [FAL#] pin. Status LED: <Green> means valid input voltage. <Amber> means a critical fault. Thermal Protection (OTP): Installed NTC and thermostat. for thermal sensor at [DEG#] pin. Leakage Current: Typ. 0.5A. Power OK Signal: Available at all output. Over Current Protection (OCP): Installed in each rail. OUTPUT SPECIFICATION Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Output Wattage: Typ. 200W continuous. Output Connector: Positronic 47-PIN PCIH47M400A1 connector. Line Regulation: Typ. 0.1%. Load Regulation: VO1 & VO2 typ. ±1.0%. VO3 & VO4 typ. ±2.0%. Noise & Ripple: Typ. 1% peak to peak or 50mV , which is greater. OVP: Built-in at all outputs. Adjustability: Available at VO1,2&3. Output Trim: Electrical trim available at VO1&2. [ADJ #]. Remote Sensing: Available at VO1,VO2 & VO3. Hot-Swap: Available. N+1 Redundancy: Installed with internal OR-ing diodes at all outputs for N+1 redundancy operation. Current Sharing: Third-wire current sharing at VO1,2 & 3. Overload Protection (OLP): Fully protected against output overload or short circuit. Typ. set at 130% max. load. Consult the factory for special OLP setting. In application
OUTPUT VOLTAGE/CURRENT RATINGS CHART MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 666.0 g (23.5 Oz.) QUAD OUTPUT MODEL NO. "⊙" Installed with Or-ing diode. " ▲" Magnetic Amplifier. " ●" Installed with Post-regulator. " ■" Common Choke. Remark: Peak load less than 60sec. with duty cycle <10%. Max. load is the continuous operating load of each rail. But the max. load of each rail can't be drawn from all outputs at the same time. INPUT & OUTPUT CONNECTORS PIN ASSIGNMENT AC INPUT QUAD OUTPUT STATUS/CONTROL CNTR &PIN # 47 46 45 1,2, 3,4 30 34 29 35 13,14, 15,16, 17,18 33 32 41 20 36 44 21 5,6,7,8,9, 10,11,12, 19,22,24 27 38 39 42 Mating connector: PCIH47F400A1. TPAC200P-490(E) TPAC200P-490(O)