TP32P0080

TP32P0080 APEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 6

Technical content

SUBMINIATURE WASHABLE MOMENTARY PUSHBUTTON SWITCHES Overview A-25 A APEM TP SERIES Number of poles

3 Single pole

4 Double pole

30 Ø 6,5 (.255) (P/N U4310) 40 Ø 5 (.196) (P/N U4320) Electrical functions

2 ON - MOM

3 OFF - MOM

W0 Right angle, horizontal mounting WW Right angle, vertical mounting MW Wire-wrap ABOUT THIS SERIES On the following pages, you will find successively : - specifications - model structure of switches - options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketted numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. Contacts and terminal materials

0 Brass, gold plated

1 Brass, silver plated

3 Brass, gold plated

(1,27 micron gold)

8 Contact brass, gold

9 Contact brass, gold

plated (1,27 micron gold) + tin plated terminals Plungers

• Short - standard
• Long
• Flush Codes : see "Options" pages. Special options

00 No special requirement

07 Trimmed terminals 3,2 (.125)

08 Extended terminals

18 Switch without ground plate

20 Ground plate with 2 pins

25 Trimmed terminals 5 (.196)

30 Wire-wrap on bracket mounting models

40 With protection cap U3500

50 Crimped ground plate pins

Packaging unit : 100 pieces, except for models with WW terminals (50 pieces).

SUBMINIATURE WASHABLE MOMENTARY PUSHBUTTON SWITCHES Specifications A-26 A APEM MATERIALS

• Case : PBT
• Actuator : polyamide, glass filled
• Contacts and terminals : 0 : brass, gold plated 1 : brass, silver plated 3 : brass, gold plated (1,27 micron gold) 8 : contact brass, gold plated + tin plated terminals 9 : contact brass, gold plated (1,27 micron gold) + tin plated terminals
• Terminal seal : epoxy GENERAL SPECIFICATIONS
• Total travel : - function 2 : 1 mm (.039) - function 3 : 0,8 mm (.031)
• Strength of terminals : pull-out force - 10N max.
• Operating temperature : -30°C to +85°C
• Moisture : 21 days 95 % (NFC 20-603 - IEC 68-2-3)
• Cleaning : solvents or water + detergent
• Wave soldering : 260°C - 5 sec. ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load : - gold plated contacts : 0,4VA 20V max. AC or DC - silver plated contacts : 0,5A 48V max. AC or DC
• Minimum load : 10mA 50mV - 10µA 5VDC
• Contact resistance : 50 mΩ max.
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength : 1.000 Vrms 50 Hz min. between terminals and frame 500 Vrms 50 Hz min. between terminals
• Electrical life at full load : - gold plated contacts : 60.000 cycles - silver plated contacts : 20.000 cycles SOLDERING Compatible wave soldering processes : see specifications S and SF, section B.

SUBMINIATURE WASHABLE MOMENTARY PUSHBUTTON SWITCHES A-27 A APEM Right angle terminals - horizontal mounting : TP..W0 Straight terminals - bracket mounting : TP..Y0 Straight PC terminals : TP..P0 MODEL STRUCTURE Function 2 Function 3 (NO) Single pole Double pole TP32P0 TP42P0 ON MOM TP33P0 TP43P0 OFF MOM

• Straight PC, right angle or wire-wrap terminals
• 1 and 2 pole configurations Single pole Double pole TP32Y0 TP42Y0 ON MOM TP33Y0 TP43Y0 OFF MOM Single pole Double pole TP32W0 TP42W0 ON MOM TP33W0 TP 43W0 OFF MOM Shown in function 2, with standard plunger Function 3 has two terminals only (3 and 1) per pole Function 3 has two terminals only (3 and 1) per pole Function 3 has two terminals only (3 and 1) per pole 3 21 31 (.027) (.129) 3.30 0.70 (.598) (.027) 15.20 0.70 ø2.50 3.55 (.139) (.098 DIA) 2.54 5.085.08 5.08 9.20 3.50 0.70 ø1.10 2.54 5.08 2.54 ø1.10 3.309.60 3.80 4.20 ø4.60 ø5.00 8.10 0.50 3.30 5.55 (.043 DIA) (.200) (.100) (.043 DIA) (.100) (.100) (.200) (.200) (.129) (.218) (.137) (.362) (.377) (.019) (.318) (.129) (.196 DIA) (.181 DIA) (.200) (.165) (.027) (.149) (.100) 2.54 31 2 654 (.100) (.043 DIA) (.200) (.100) (.043 DIA) (.149) (.165) (.358) (.039) (.181 DIA) (.196 DIA) (.139) (.019) (.098 DIA) (.129) (.196) 5.00 0.50 Ø 4.60 Ø 5.00 4.20 3.80 9.10 2.54 Ø 1.10 2.54 Ø 1.10Ø 2.50 5.08 1.00 3.55 3.30 0.70 (.027) (.240) 6.10 (.318) 8.10 5.08 (.200) 2.54 (.100) (.318) 8.10 123 456 (.027) 0.70 3.30 8.60 3.555.70 1.00 5.08 Ø 2.50 Ø 1.10 10.16 2.54 Ø 1.10 10.16 2.549.10 3.80 4.20 0.70 Ø 5.00 Ø 4.60 0.50 10.165.00 0.40 (.196) (.129) (.338) (.098 DIA) (.019) (.224) (.139) (.400) (.015) (.196 DIA) (.181 DIA) (.039) (.358) (.027) (.165) (.149) (.043 DIA) (.400) (.100) (.200) (.043 DIA) (.400) (.100) 123 456

SUBMINIATURE WASHABLE MOMENTARY PUSHBUTTON SWITCHES A-28 A APEM Wire-wrap terminals : TP..MW Right angle terminals - vertical mounting : TP..WW Single pole Double pole TP32WW TP42WW ON MOM TP33WW TP43WW OFF MOM Single pole Double pole TP32MW TP42MW ON MOM TP33MW TP43MW OFF MOM PCB MOUNTING Shown in function 2, with standard plunger Function 3 has two terminals only (3 and 1) per pole Function 3 has two terminals only (3 and 1) per pole (.559) (.562) (.120) (.218) (.340) (.181) 14.20 14.30 3.05 5.55 4.60 8.65 5.00 (.196) (.377) 9.60 0.50 5.08 9.20 3.50 3.55 5.08 5.08 2.54 5.08 5.08 3.80 5.08 5.08 8.65 3.300.70 4.20 (.043 DIA) Ø 1.10 (.043 DIA) Ø 1.10 (.100) (.200) (.200) (.200) (.019) (.149) (.165) (.027) (.139) (.137) (.200) (.362)(.200) (.340) (.200) (.200) (.129) (.358) 9.10 (.196) 5.00 (.098 DIA) Ø 2.50 (.196 DIA) (.181 DIA) Ø 4.60 Ø 5.00 (.100) 2.54 8.10 (.318) 6.10 (.240) (.027) 0.70 15.20 3.55 1.00 5.08 Ø 2.50 Ø 1.10 2.54 Ø 1.10 2.54 9.10 3.80 4.20Ø 5.00 Ø 4.60 0.50 5.00 (.196) (.598) (.098 DIA) (.019) (.139) (.196 DIA) (.181 DIA) (.039) (.358) (.165) (.149) (.043 DIA) (.100) (.200) (.043 DIA) (.100) (.200) 5.08 2.54 (.100) 231 4 56

SUBMINIATURE WASHABLE MOMENTARY PUSHBUTTON SWITCHES A-29 A APEM CONTACT AND TERMINAL MATERIALS

3 Brass, gold plated (1,27 micron gold)

8 Contact brass, gold plated + tin plated terminals

9 Contact brass, gold plated (1,27 micron gold) + tin plated terminals

Standard plunger colour is black. Short - standard Long Flush With blue case With black case With blue case With black case With black case SPECIAL OPTIONS 07 Trimmed terminals - length 3,2 mm (.125) for TP..WW models only 08 Extended terminals for TP..W0 models only (.098 DIA) (.149) (.165) (.139) (.181 DIA) (.196 DIA) (.240) Ø 4.60 Ø 5.004.20 3.80 Ø 2.50 3.556.10 Ø 2.50 3.80 4.20 Ø 5.00 Ø 4.60 (.196 DIA) (.181 DIA) (.165) (.149) (.098 DIA) (.177) 4.506.10 (.240) (.149) (.165) (.181 DIA) (.196 DIA) (.240) Ø 4.60 Ø 5.004.20 3.80 6.10 (.125) 3.20 (.492) 12.50

SUBMINIATURE WASHABLE MOMENTARY PUSHBUTTON SWITCHES A-30 A APEM 4030 (.118) 3.00 (.153) Ø 5.00 3.90 (.196 DIA) 4.00 (.157) Ø 6.50 3.00 (.118) (.255) 18 Switch without ground plate for TP..WW models only 25 Trimmed terminals - length 5 mm (.196) for all models, except TP..WW 50 Crimping of ground plate pins . Retains switch on PC during handling and wave soldering. 20 Ground plate with 2 pins for TP..WW models only

30 Wire-wrap terminals on models with mounting bracket

40 With cap U3500 mounted over plunger and bushing

Further protects the switch during PCB processing CAPS Cap colours Replace "0" by number 1 blue 2 black 3 green 4 grey 5 yellow 6 red 7 ivory 7/1 white 9 orange SPECIAL OPTIONS (continued) To order caps separately, use their part number (U...). (.196) 5.00 2.70 (.106) 10.16 (.400) (.598) 15.20 P/N U4310 - for long plunger only P/N U4320 - for long plunger only