TNC-PJ-1.5DXW-CR10-M-CF

TNC-P-3-CF DDK | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 15

Technical content

http://www.ddknet.co.jp ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. TNC Series TNC Style Connector 150424 Frequency Range DC to 2GHz 50 Ω Lock Type Characteristic Impedance Screw FEATURE Characteristic Impedance 50 Ω Rated Voltage 500VAC(r.m.s.) Dielectric Withstanding Voltage 500V AC(r.m.s) / 1 minute Insulation Resistance 1,000M Ω min. at 500V DC Contact Resistance 3m Ω max. Operating Temperature -55 〜 +85℃ RoHS Compliant RoHS Compliant Item Material / Finish Shell Copper Alloy / Ni or Ag Plating Contact (Female) Copper Alloy / Ag or Au Plating Contact (Male) Copper Alloy /Ag or Au Plating Insulator PTFE Gasket Silicon Rubber SPECIFICATIONS MATERIAL/FINISH ＊ The specifications are typical but may not apply to all connectors. Please check the specifications on each item with its drawing from us when you use. ・ TNC series is a thread coupling coaxial connector which is modified BNC style connector. ・ Due to the thread coupling, it is superior to BNC style connector in vibration load. ・ Other electrical and mechanical characteristics are same as BNC style connector. ・ Recommended toque of coupling is 45 〜 68.6N・cm. CONFORMING STANDARD MIL-PRF-39012

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Straight Cable Plug Clamp Type Part Number Applicable Cable L Finish Assembly InstructionOuter Conductor Center Conductor TNC-P-3-CF 3D-2V

25.0 Ag Ag 6

Part Number Applicable Cable φA L Finish Assembly Instruction Crimp ToolOuter Conductor Center Conductor TNC-P-1.5DQEW-CF 1.5D-2W 5.5 22.3 Ni Au 1 CR-H-1100 1.5D-QEW TNC-P-2.5D2W-CR10-CF 2.5D-2W 6.3 24.3 Ni Ag 2 CR-H-1115 2.5D-QEW TNC-P-3D2W-CR10-CF 3D-2W 7.9 24.3 Ni Ag 2 CR-H-1135 3D-QEW Crimp Type Part Number Applicable Cable φA L Finish Assembly InstructionCrimp ToolOuter Conductor Center Conductor TNC-P-2DFB-1-CF 2D-FB 6.2 29.7 Ni Au 3 CR-H-1105 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Straight Cable Jack Part Number Applicable Cable φA φB L Finish Assembly Instruction Crimp ToolOuter Conductor Center Conductor TNC-BJ-2.5D-QEW-CF 2.5D-2W 14.0 6.25 27.9 Ni Ag 4 CR-H-1105 2.5D-QEW L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 ※ Mounting Panel Thickness：2.7mm max. Part Number Applicable Cable φA φB L Finish Assembly Instruction Crimp ToolOuter Conductor Center Conductor TNC-J-1.5DXW-CR10-120-CF 2D-FB 5.5 12.0 26.8 Ni Ag 4 CR-H-1142 TNC-J-2.5D2W-CR10-CF 2.5D-2W 6.25 14.6 25.0 Ni Ag 4 CR-H-1105 2.5D-QEW Crimp Type L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 Part Number Applicable Cable φA φB L Finish Assembly Instruction Crimp ToolOuter Conductor Center Conductor TNC-J-3D2W-CR10-CF 3D-2W 7.9 14.6 25.42 Ni Ag 4 CR-H-1135 3D-QEW ○ Straight Bulkhead Cable Jack

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. Part Number Applicable Cable Finish Assembly Instruction Crimp ToolOuter Conductor Center Conductor TNC-PJ-1.5DQEW-CR10-CF 1.5D-QEW Ni Ag 5 CR-H-1142 1.5D-2W L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 Part Number Applicable Cable Finish Assembly Instruction Crimp ToolOuter Conductor Center Conductor TNC-PJ-1.5DXW-CR10-M-CF 1.5D-XW Ni Ag 7 CR-H-1100 1.5D-XWTA L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 Panel Mounting Dimensions Crimp Type Part Number Applicable Cable Finish Assembly Instruction Crimp ToolOuter Conductor Center Conductor TNC-PJ-2H-1.5D-CR10-CF 1.5D-QEV Ni Ag 5 CR-H-1101 1.5D-2V L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 L L φA TNC-P-2DFB-1 L φA TNC-J-1.5DXW-CR10-120 L φA φB L 17.0 φB φA 5.0 TNC-J-3D2W-CR10 TNC-BJ-2.5DQEW Panel Mounting Dimensions φB φA L 10.2 16.82 (Detent Diameter） (Flat Diameter） 10.4 +0.1 φ11.2 +0.1 TNC-PJ-1.5DXW-CR10-M TNC-PJ-1.5DQEW-CR10 26.8 φ5.5 15.82.3 □17.5 12.7 12.7 4-φ3.0 12.7 4-φ3.0 φ12.0 30.8 15.82.3 φ5.5 18.2±0.05 18.2±0.05 12.7 □25.4 18.2 18.2 4-M2.5×0.45 φ12.0 TNC-PJ-2H-1.5D-CR10 23.4 18.0 24.4 14.72.3 18.0 φ6.0 2-φ3.2 2-φ3.2 4-φ3.0 +0.1 +0.1 ○ Straight Panel Cable Jack Panel Mounting Dimensions Panel Mounting Dimensions

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. Part Number Finish Outer Conductor Center Conductor TNC-R-CF Ag Au TNC-R-NiCAu-CF Ni Au TNC-R TNC-R-NiAU TNC-R2-Ni TNC-R2 TNC-R2-2H-Ni TNC-SR-3 TNC-SR-6 TNC-SR-9 23.3 26.3 15.82.3 φ1.4 12.7±0.05 12.7 □17.5 12.7 4-M2.6×0.45 12.7±0.05 φ11.1 +0.2 4-φ2.8±0.15 □17.5 12.7 26.3 15.82.3 φ1.4 12.7 12.7±0.05 12.7±0.05 φ11.1 +0.2 4-φ3.0 +0.1 04-φ3.0 26.3 15.82.3 18±0.05 φ1.4 2-φ3.0 2-φ3 +0.1 φ9.0 +0.1 27.7 15.89.6 φ1.7 φ5.4 4 2.3 □17.5 12.7 □17.5 12.7 12.7 4-φ3.0 12.7±0.05 12.7±0.05 φ12 +0.1 4-φ3.0 +0.1 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 12.7 φ4.0 17.8 6.8 26.6 φ1.27 -0.1 17.8 8.5 2 26.6 φ4.0 φ1.27 -0.1 4-φ3.0 (Thru-Hole） □17.5 12.7 12.7 4-φ3.0 (Thru-Hole） 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 Part Number Finish Outer Conductor Center Conductor TNC-R2-CF Ag Ag TNC-R2-Ni-CF Ni Ag TNC-R2-NiCAu-CF Ni Au TNC-R TNC-R-NiAU TNC-R2-Ni TNC-R2 TNC-R2-2H-Ni TNC-SR-3 TNC-SR-6 TNC-SR-9 23.3 26.3 15.82.3 φ1.4 12.7±0.05 12.7 □17.5 12.7 4-M2.6×0.45 12.7±0.05 φ11.1 +0.2 4-φ2.8±0.15 □17.5 12.7 26.3 15.82.3 φ1.4 12.7 12.7±0.05 12.7±0.05 φ11.1 +0.2 4-φ3.0 +0.1 04-φ3.0 26.3 15.82.3 18±0.05 φ1.4 2-φ3.0 2-φ3 +0.1 φ9.0 +0.1 27.7 15.89.6 φ1.7 φ5.4 4 2.3 □17.5 12.7 □17.5 12.7 12.7 4-φ3.0 12.7±0.05 12.7±0.05 φ12 +0.1 4-φ3.0 +0.1 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 12.7 φ4.0 17.8 6.8 26.6 φ1.27 -0.1 17.8 8.5 2 26.6 φ4.0 φ1.27 -0.1 4-φ3.0 (Thru-Hole） □17.5 12.7 12.7 4-φ3.0 (Thru-Hole） 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 Part Number Finish Outer Conductor Center Conductor TNC-R2-2H-Ni-CF Ni Ag TNC-R TNC-R-NiAU TNC-R2-Ni TNC-R2 TNC-R2-2H-Ni TNC-SR-3 TNC-SR-6 TNC-SR-9 23.3 26.3 15.82.3 φ1.4 12.7±0.05 12.7 □17.5 12.7 4-M2.6×0.45 12.7±0.05 φ11.1 +0.2 4-φ2.8±0.15 □17.5 12.7 26.3 15.82.3 φ1.4 12.7 12.7±0.05 12.7±0.05 φ11.1 +0.2 4-φ3.0 +0.1 04-φ3.0 26.3 15.82.3 18±0.05 φ1.4 2-φ3.0 2-φ3 +0.1 φ9.0 +0.1 27.7 15.89.6 φ1.7 φ5.4 4 2.3 □17.5 12.7 □17.5 12.7 12.7 4-φ3.0 12.7±0.05 12.7±0.05 φ12 +0.1 4-φ3.0 +0.1 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 12.7 φ4.0 17.8 6.8 26.6 φ1.27 -0.1 17.8 8.5 2 26.6 φ4.0 φ1.27 -0.1 4-φ3.0 (Thru-Hole） □17.5 12.7 12.7 4-φ3.0 (Thru-Hole） 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 ○ Receptacle Jack Panel Mounting Dimensions Panel Mounting Dimensions Panel Mounting Dimensions

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Receptacle Jack Part Number Finish Outer Conductor Center Conductor TNC-SR-3-CF Ni Au Part Number Finish Outer Conductor Center Conductor TNC-SR-6-CF Ni Au Part Number Finish Outer Conductor Center Conductor TNC-SR-9-CF Ni Au TNC-R TNC-R-NiAU TNC-R2-Ni TNC-R2 TNC-R2-2H-Ni TNC-SR-3 TNC-SR-6 TNC-SR-9 23.3 26.3 15.82.3 φ1.4 12.7±0.05 12.7 □17.5 12.7 4-M2.6×0.45 12.7±0.05 φ11.1 +0.2 4-φ2.8±0.15 □17.5 12.7 26.3 15.82.3 φ1.4 12.7 12.7±0.05 12.7±0.05 φ11.1 +0.2 4-φ3.0 +0.1 04-φ3.0 26.3 15.82.3 18±0.05 φ1.4 2-φ3.0 2-φ3 +0.1 φ9.0 +0.1 27.7 15.89.6 φ1.7 φ5.4 4 2.3 □17.5 12.7 □17.5 12.7 12.7 4-φ3.0 12.7±0.05 12.7±0.05 φ12 +0.1 4-φ3.0 +0.1 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 12.7 φ4.0 17.8 6.8 26.6 φ1.27 -0.1 17.8 8.5 2 26.6 φ4.0 φ1.27 -0.1 4-φ3.0 (Thru-Hole） □17.5 12.7 12.7 4-φ3.0 (Thru-Hole） 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 TNC-R TNC-R-NiAU TNC-R2-Ni TNC-R2 TNC-R2-2H-Ni TNC-SR-3 TNC-SR-6 TNC-SR-9 23.3 26.3 15.82.3 φ1.4 12.7±0.05 12.7 □17.5 12.7 4-M2.6×0.45 12.7±0.05 φ11.1 +0.2 4-φ2.8±0.15 □17.5 12.7 26.3 15.82.3 φ1.4 12.7 12.7±0.05 12.7±0.05 φ11.1 +0.2 4-φ3.0 +0.1 04-φ3.0 26.3 15.82.3 18±0.05 φ1.4 2-φ3.0 2-φ3 +0.1 φ9.0 +0.1 27.7 15.89.6 φ1.7 φ5.4 4 2.3 □17.5 12.7 □17.5 12.7 12.7 4-φ3.0 12.7±0.05 12.7±0.05 φ12 +0.1 4-φ3.0 +0.1 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 12.7 φ4.0 17.8 6.8 26.6 φ1.27 -0.1 17.8 8.5 2 26.6 φ4.0 φ1.27 -0.1 4-φ3.0 (Thru-Hole） □17.5 12.7 12.7 4-φ3.0 (Thru-Hole） 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 TNC-R TNC-R-NiAU TNC-R2-Ni TNC-R2 TNC-R2-2H-Ni TNC-SR-3 TNC-SR-6 TNC-SR-9 23.3 26.3 15.82.3 φ1.4 12.7±0.05 12.7 □17.5 12.7 4-M2.6×0.45 12.7±0.05 φ11.1 +0.2 4-φ2.8±0.15 □17.5 12.7 26.3 15.82.3 φ1.4 12.7 12.7±0.05 12.7±0.05 φ11.1 +0.2 4-φ3.0 +0.1 04-φ3.0 26.3 15.82.3 18±0.05 φ1.4 2-φ3.0 2-φ3 +0.1 φ9.0 +0.1 27.7 15.89.6 φ1.7 φ5.4 4 2.3 □17.5 12.7 □17.5 12.7 12.7 4-φ3.0 12.7±0.05 12.7±0.05 φ12 +0.1 4-φ3.0 +0.1 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 12.7 φ4.0 17.8 6.8 26.6 φ1.27 -0.1 17.8 8.5 2 26.6 φ4.0 φ1.27 -0.1 4-φ3.0 (Thru-Hole） □17.5 12.7 12.7 4-φ3.0 (Thru-Hole） 12.7±0.05 12.7±0.05 φ4.1 +0.1 4-φ3.1 +0.1 Panel Mounting Dimensions Panel Mounting Dimensions Panel Mounting Dimensions

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Receptacle Plug ○ Right Angle Receptacle Jack Part Number Finish Outer Conductor Center Conductor TNC-PR-CF Ag Ag Part Number Finish Outer Conductor Center Conductor TNC-LR-CF Ag Au TNC-LR-Ni-CF Ni Ag Part Number Finish Outer Conductor Center Conductor TNC-LR-1-CF Ag Ag TNC-PR TNC-LR-Ni TNC-LR TNC-LR-1 28.5 18.0 12.7±0.05 12.7±0.05 4-φ3.2 +0.1 φ9.0 +0.1 □17.5 12.7 φ1.1 φ2.29 4-φ3.0 12.7 2.3 φ14.6 12.7±0.05 12.7±0.05 4-φ3 +0.1 φ9.0 +0.1 12.7 14.3 2.3 □17.5 12.7 □17.512.7 12.7 4-φ3.0 4-M2.6 φ1.1 φ2.29 φ1.1 φ2.29 21.6 23.1 14.3 2.3 TNC-PR TNC-LR-Ni TNC-LR TNC-LR-1 28.5 18.0 12.7±0.05 12.7±0.05 4-φ3.2 +0.1 φ9.0 +0.1 □17.5 12.7 φ1.1 φ2.29 4-φ3.0 12.7 2.3 φ14.6 12.7±0.05 12.7±0.05 4-φ3 +0.1 φ9.0 +0.1 12.7 14.3 2.3 □17.5 12.7 □17.512.7 12.7 4-φ3.0 4-M2.6 φ1.1 φ2.29 φ1.1 φ2.29 21.6 23.1 14.3 2.3 TNC-PR TNC-LR-Ni TNC-LR TNC-LR-1 28.5 18.0 12.7±0.05 12.7±0.05 4-φ3.2 +0.1 φ9.0 +0.1 □17.5 12.7 φ1.1 φ2.29 4-φ3.0 12.7 2.3 φ14.6 12.7±0.05 12.7±0.05 4-φ3 +0.1 φ9.0 +0.1 12.7 14.3 2.3 □17.5 12.7 □17.512.7 12.7 4-φ3.0 4-M2.6 φ1.1 φ2.29 φ1.1 φ2.29 21.6 23.1 14.3 2.3 Panel Mounting Dimensions Panel Mounting Dimensions

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Dust Cap TNC-RC-1-D1 26357-001 1 1 バヨネッ ト 黄 銅 銀めっき 1 2 ガ ス ケ ット シリ コンゴム 1 3 ディスク 黄 銅 ニッケルめっき 1 4 ボールチ ェーン 黄 銅 1 5 カップリング 黄 銅 (60) (75) （φ3.5） クロームめっき クロームめっき 7/16-28UNEF-2B 適合コネク タ ： TNC形ジャ ッ ク 注1． 符号④ボールチ ェーンの外れ、 切れの原因となり ます ので、 ボールチ ェーン及び接続部に58.8N （6kgf） 以上の 負荷をかけてのご使用は、 ご遠慮下さい。 2． カッ プリ ング締付け トルク ： 9.8～39.2N ・ cm （1～4kgf ・ cm） （φ14.5） TNC-C-2-D1-CF 26321-001-CF 材質 1 1 1 2 ディスク ガ ス ケ ット カップリング 銅合金 ニッケルめっき シリコンゴ ム 仕様 １． 適合コネク タ ： ＴＮＣ形ジャ ッ ク ２． カッ プリ ング締付け トルク ： ９． ８～３９． ２Ｎ ・ ｃｍ （１～４ｋｇｆ ・ ｃｍ） (φ14.5) 7/16-28UNEF-2B 1 銀めっき銅合金 Part Number Finish TNC-C-2-CF Ni TNC-C-2-D1-CF Ag Part Number Finish TNC-RC-1 Ni TNC-RC-1-D1 Ag

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Assembly Instruction（1） ① Insert the heat-shrinkable tube onto the cable. Cut the cable as fig.1. Please be careful to not damage the outer conductor. ② Insert the ferule on the outer conductor and spread the top of the outer conductor. Insert the sleeve between insulator and outer conductor. And cut the outer conductor along the sleeve. ③ ③ Cut the insulator as fig. 3. Please be careful to not damage the center conductor. Pre-solder the center conductor and cut the center conductor. Please be careful to not damage the insulator by soldering. Insert the insulator as fig.3. ④ Solder up the contact with center conductor. No gap between insulator and contact. ⑤ Insert the body into the above cable assembly. And crimp the root of the body. Please be careful to meet the crimp height as follows. ⑥ Cover the heat-shrinkable tube on the root of the body and heat up. Parts Configulration Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Note） Distance between body and contact must be met. L Cable length Heat-shrinkable tube Ferule Sleeve Insulator Contact Body 14.7±0.5 Outer ConductorHeat-shrinkable tube Sheath Insulator Ferule Sleeve Center Conductor Insulator No gap Contact Soldering Measuring point(3.1) Heat-shrinkable tube Dies Ａ 6.2 -0.5 4 +0.2 -0.3 Insulator Outer Conductor 5.33～5.84 (between body and contact) (Pre-soldering) A B C Cable length which require for the cable assembly. L=L1-3.3 L=L2+19.7

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Assembly Instruction（2） Sleeve Ferule Outer Conductor Outer ConductorSheath Cable Boot BA Center Conductor Center Conductor Crimp Tool Insulator Crimping Dies No gap Contact Contact crimped Boot Ferule Sleeve Contact Body BodyCrimp Tool Body Surface Tool Surface Boot Sleeve Ferule Outer Conductor Outer ConductorSheath Cable Boot BA Center Conductor Center Conductor Crimp Tool Insulator Crimping Dies No gap Contact Contact crimped Boot Ferule Sleeve Contact Body BodyCrimp Tool Body Surface Tool Surface Boot ① Insert the boot into the cable and cut the cable as fig.1. Please be careful to not damage the outer conductor. ② Insert the ferule on the outer conductor and spread the top of the outer conductor. Press-in rhe sleeve between insulator and outer conductor. Cut the extra outer conductor along the sleeve. ③ Cut the insulator and center conductor as fig.3. Part Number A B TNC-P-2.5D2W-CR10-CF 5.0mm 4.0mm TNC-P-3D2W-CR10-CF 5.5mm 3.5mm ④ Pinch the contact in the crimping hole(center hole) and insert the center conductor of the cable. Crimp the contact (match the side hole of contact with the curve of crimping hole of tool.) Part Number Crimp Tool TNC-P-2.5D2W-CR10-CF CR-H-1115 TNC-P-3D2W-CR10-CF CR-H-1135 ⑤ Insert the above contact into the body. Match the key in the insulator and keyway of the contact. Crimp the root of body as fig.5. Cover the boot on the root of the connector body. Parts Configulration

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Assembly Instruction（3） BodySleeveBoot Contact assembly Outer ConductorSheath Boot Sleeve Cable Insulator Cente Conductor （Cut off afterpre-soldering) Outer Conductor Aluminum foil tape Body Boot Sleeve Contact assembly Soldering BodySleeveBoot Contact assembly Outer ConductorSheath Boot Sleeve Cable Insulator Cente Conductor （Cut off afterpre-soldering) Outer Conductor Aluminum foil tape Body Boot Sleeve Contact assembly Soldering ① Insert the boot and sleeve into the cable and cut the cable as fig.1. Please be careful to not damage the outer conductor. ② Cut the cable as fig.2. Cut the center conductor after pre-soldering. ③ Insert the contact between outer conductor and aluminum foil tape. Solder the contact with center conductor. When the solder is stick out, please shave the extra solder along the contact. ④ Cover the sleeve on the outer conductor and crimp as fig.4. Crimp Tool : (CR-H-1105) ⑤ Insert the above contact into the body and screw. Cover the boot on the root of the body. Parts Configulration

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Assembly Instruction（4） A Outer ConductorSheath Cable Heat-shrinkable tube Outer Conductor SleeveFerule Spread the top B ● C Insulator Center Conductor （Pre-soldering） Outer Conductor Sleeve Contact Soldering No gap Insulator Heat-shrinkable tube Crimping Dies same level Contact BodyInsulatorSleeveFeruleHeat-shrinkable tube A Outer ConductorSheath Cable Heat-shrinkable tube Outer Conductor SleeveFerule Spread the top B ● C Insulator Center Conductor （Pre-soldering） Outer Conductor Sleeve Contact Soldering No gap Insulator Heat-shrinkable tube Crimping Dies same level Contact BodyInsulatorSleeveFeruleHeat-shrinkable tube ① Insert the heat-shrinkable tube into the cable and cut the cable as fig.1. Please be careful to not damage the outer conductor. Part Number A TNC-J-1.5DXW-CR10-120-CF 13.0mm TNC-J-2.5D2W-CR10-CF 11.0mm TNC-J-3D2W-CR10-CF 11.5mm TNC-BJ-2.5DQEW-CF 13.0mm ② Insert the ferule on the outer conductor and spread the top of the outer conductor. Press in the sleeve between outer conductor and insulator. ③ Cut off the extra outer conductor along the sleeve. Cut the cable as fig.3. Cut the center conductor after pre-soldering. Please be careful to not damage the center conductor. Part Number B C TNC-J-1.5DXW-CR10-120-CF 5.7mm 2.8mm TNC-J-2.5D2W-CR10-CF 3.0mm 2.5mm TNC-J-3D2W-CR10-CF 3.1mm 2.5mm TNC-BJ-2.5DQEW-CF 6.0mm 2.0mm ④ Insert the insulator and solder the contact with center conductor. When the solder is stick out, please shave the extra solder along the contact. Part Number Tool TNC-J-1.5DXW-CR10-120-CF CR-H-1100 TNC-J-2.5D2W-CR10-CF CR-H-1105 TNC-J-3D2W-CR10-CF CR-H-1135 TNC-BJ-2.5DQEW-CF CR-H-1105 ⑤ Insert the above contact into the body. Match the key in the insulator and keyway of the contact. Crimp the root of body as fig.5. ⑥ Cover the heat-shrinkable tube on the root of the body and heat up. Parts Configulration

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Assembly Instruction（5） BodyContactInsulatorSleeveFeruleHeat-shrinkable tube A Sheath Outer Conductor InsulatorFerule Spread the top Center Conductor （Pre-soldering） Sleeve B ● C Cut the center conductor after pre-soldering Contact Insulator Soldering No gap same level Body Crimping Dies Heat-shrinkable tube BodyContactInsulatorSleeveFeruleHeat-shrinkable tube A Sheath Outer Conductor InsulatorFerule Spread the top Center Conductor （Pre-soldering） Sleeve B ● C Cut the center conductor after pre-soldering Contact Insulator Soldering No gap same level Body Crimping Dies Heat-shrinkable tube ① Cut the cable as fig.1. Please be careful to not damage the outer conductor. Part Number A TNC-PJ-1.5DQEW-CR10-CF 13.0mm TNC-PJ-2H-1.5D-CR10-CF 10.0mm ② Insert the ferule on the outer conductor and spread the top of the outer conductor. ③ Insert the sleeve and cut the cable as fig.3. Press in the sleeve between outer conductor and insulator. Cut off the extra outer conductor along the sleeve. Cut the insulator and center conductor as below table. Cut the center conductor after pre-soldering. Please be careful to not damage the center conductor. Part Number B C TNC-PJ-1.5DQEW-CR10-CF 5.7mm 3.0mm TNC-PJ-2H-1.5D-CR10-CF 4.0mm 3.0mm ④ Insert the insulator on the insulator of the cable and solder the contact with center conductor. When the solder is stick out, please shave the extra solder along the contact. ⑤ Insert the above contact into the body. Match the key in the insulator and keyway of the contact. Crimp the root of body as fig.5. ⑥ Cover the heat-shrinkable tube on the root of the body and heat up. Parts Configulration Part Number Tool TNC-PJ-1.5DQEW-CR10-CF CR-H1142 TNC-PJ-2H-1.5D-CR10-CF CR-H1101

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Assembly Instruction（6） Nut Washer Gasket Clamp Contact Body L 3D-2V Outer ConductorSheath Gasket WasherNut Insulator Center Conductor （Pre-soldering） Clamp Pick the outer conductor and turn down to the clamp Trim the outer conductor along the clamp +0.5 -0.53 Soldering Contact No gapInsulator Body Body assembly （Gap between body and contact） 0.21 +0.23 -0.13Flat Diameter：9.5±0.2 Flat Diameter： 9.5±0.2 Nut Washer Gasket Clamp Contact Body L 3D-2V Outer ConductorSheath Gasket WasherNut Insulator Center Conductor （Pre-soldering） Clamp Pick the outer conductor and turn down to the clamp Trim the outer conductor along the clamp +0.5 -0.53 Soldering Contact No gapInsulator Body Body assembly （Gap between body and contact） 0.21 +0.23 -0.13Flat Diameter：9.5±0.2 Flat Diameter： 9.5±0.2 ① The cable length require for the cable assembly L1=L-x ② Insert nut, washer and gasket into the cable and cut the cable as fig.2. Please be careful to not damage the outer conductor. ③ Insert the clamp on the outer conductor and turn down the outer conductor. Cut the outer conductor along the clamp. Cut the insulator as fig.3. Please be careful to not damage the center conductor. Cut the center conductor after pre-soldering. ④ Insert the contact and solder the contact with center conductor. Please bee careful to not damage the insulator by heat. ⑤ Insert the above contact into the body. Insert the the gasket and washer into the body and screw the nut. Recommended torque : 117.5 〜 147N・cm (12 〜 15Kgf・cm） Parts Configulration

Unit：mm http://www.ddknet.co.jp TNC Series ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. ○ Assembly Instruction（7） 4±0.5 (9.7) 2.9 Pre-soldering Same level （between contact and washer Body Surface Interface Dimension Crimp Height Heat-shrinkable tube Ferule Insulator Contact Body Cable Outer Conductor Heat-shrinkable tube Sheath Ferule Pick and spread the top Insulator Center Conductor Insulator Contact Soldering No gap b a c L/2 L Measurering point Body 4.98±0.25 Dies ： A Cable assembly Heat-shrinkable tube 4±0.5 (9.7) 2.9 Pre-soldering Same level （between contact and washer Body Surface Interface Dimension Crimp Height Heat-shrinkable tube Ferule Insulator Contact Body Cable Outer Conductor Heat-shrinkable tube Sheath Ferule Pick and spread the top Insulator Center Conductor Insulator Contact Soldering No gap b a c L/2 L Measurering point Body 4.98±0.25 Dies ： A Cable assembly Heat-shrinkable tube 4±0.5 (9.7) 2.9 Pre-soldering Same level （between contact and washer Body Surface Interface Dimension Crimp Height Heat-shrinkable tube Ferule Insulator Contact Body Cable Outer Conductor Heat-shrinkable tube Sheath Ferule Pick and spread the top Insulator Center Conductor Insulator Contact Soldering No gap b a c L/2 L Measurering point Body 4.98±0.25 Dies ： A Cable assembly Heat-shrinkable tube 4±0.5 (9.7) 2.9 Pre-soldering Same level （between contact and washer Body Surface Interface Dimension Crimp Height Heat-shrinkable tube Ferule Insulator Contact Body Cable Outer Conductor Heat-shrinkable tube Sheath Ferule Pick and spread the top Insulator Center Conductor Insulator Contact Soldering No gap b a c L/2 L Measurering point Body 4.98±0.25 Dies ： A Cable assembly Heat-shrinkable tube 4±0.5 (9.7) 2.9 Pre-soldering Same level （between contact and washer Body Surface Interface Dimension Crimp Height Heat-shrinkable tube Ferule Insulator Contact Body Cable Outer Conductor Heat-shrinkable tube Sheath Ferule Pick and spread the top Insulator Center Conductor Insulator Contact Soldering No gap b a c L/2 L Measurering point Body 4.98±0.25 Dies ： A Cable assembly Heat-shrinkable tube 4±0.5 (9.7) 2.9 Pre-soldering Same level （between contact and washer Body Surface Interface Dimension Crimp Height Heat-shrinkable tube Ferule Insulator Contact Body Cable Outer Conductor Heat-shrinkable tube Sheath Ferule Pick and spread the top Insulator Center Conductor Insulator Contact Soldering No gap b a c L/2 L Measurering point Body 4.98±0.25 Dies ： A Cable assembly Heat-shrinkable tube 4±0.5 (9.7) 2.9 Pre-soldering Same level （between contact and washer Body Surface Interface Dimension Crimp Height Heat-shrinkable tube Ferule Insulator Contact Body Cable Outer Conductor Heat-shrinkable tube Sheath Ferule Pick and spread the top Insulator Center Conductor Insulator Contact Soldering No gap b a c L/2 L Measurering point Body 4.98±0.25 Dies ： A Cable assembly Heat-shrinkable tube Parts Configulration Cable length which require for the cable assembly. L=L1-10.5 ① Insert the heat-shrinkable tube into the cable. Cut the cable as fig.1. Note）Please be careful to not damage the outer conductor. ② Insert the ferule on the outer conductor Pick and spread the outer conductor. ③ Turn down the outer conductor to the ferule and cut the outer conductor as fig.3. Cut the insulator as fig. 3 and pre-solder the center conductor. And cut the center conductor as fig.3. Note）Please be careful to not center conductor. ④ Insert the insulator into the cable, solder up the contact with center conductor. Note）When the solder is stick out, please shave the extra solder along the contact. ⑤ Insert the body into the above cable assembly and crimp the root of the body. Note）When inserting the body, match the contact notch with projection of insulator. Note）Crimp the body with same level of body and dies. Note）Meet the interface dimension and crimp height ⑥ Cover the heat-shrinkable tube on the root of the body and heat up.