TMXW340 RAKON | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 7

Technical content

Issue: Rev 3, 11 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved www.rakonxpress.com Table of Contents TMX W340 SAW Filter datasheet 3.0 x 3.0 mm, SMD

SAW Bandpass Filters | Wireless Communications Issue: Rev 3, 11 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 1 of 6 www.rakonxpress.com

Features

Parameter Min. Typ. Max. Unit Storage temperature range (Tstg) -40 85 °C Operating temperature range (TA) -30 75 °C DC permissive voltage 3 V Maximum Input Power Handling 10 dBm Frequency and electrical characteristics (Reference temperature @ 25°C) Parameter Min. Typ.1 Max. Unit Center frequency (fc) 866 MHz Bandwidth @ -1.5 dB (BW, passband width) 12.00 35.00 MHz Insertion Loss (IL, 860 – 872 MHz) 2.0 3.5 dB Absolute Attenuation From 770 to 780 MHz From 815 to 825 MHz dB Source impedance2 (Single ended) 50 Ω Load impedance2 (Single ended) 50 Ω

1 Typical values are nominal performances at room temperature

2 No external matching is required

Features Applications 3.0 x 3.0 mm  866.0 MHz center frequency  Ceramic package for Surface Mounted Technology  Bandwidth at -1.5db : 12 MHz min / 35 MHz typ  No external matching is required  Remote control - RF  Wireless applications

SAW Bandpass Filters | Wireless Communications Issue: Rev 3, 11 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 2 of 6 www.rakonxpress.com Model outline, pin connection and marking Test circuit Pin Connections B Input E Output A, C, D, F Case Ground Marking Note Line 1 W340 RakonXpress designation Line 2 S632 T = production Code 6 = Year 2016 32 = Week 32 Line 3 •AA • = Identify black dot AA = Internal Code (Wafer Batch) 50 Ω / 50 Ω Configuration Unit: mm 3.0 ±0.1 SQ SIDE VIEW TOP VIEW A B C F E D W340 T632

  • AA FRONT VIEW 1.4 max 1.0 max BOTTOM VIEW A B C 1.5 0.85 0.6 F E D 2.8 1.3 1.6 RECOMMENDED PAD LAYOUT TOP VIEW 1.7 3.2 1.05 1.1 0.9 0.3 SAW Filter Input Single, 50 Ω Output Single, 50 Ω GND A, C, D, F E B

SAW Bandpass Filters | Wireless Communications Issue: Rev 3, 11 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 3 of 6 www.rakonxpress.com Frequency characteristics TYPICAL S21 RESPONSE

SAW Bandpass Filters | Wireless Communications Issue: Rev 3, 11 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 4 of 6 www.rakonxpress.com Recommended reflow soldering profile NOTE:

  • The components shall remain within the electrical specifications after it soldered on the 1mm thickness PCB board and dipped in the solder at 260 ±5°C during 10 ± 1 seconds.
  • The components shall remain within the electrical specifications after it soldered by electric iron, solder at 350 ± 10 °C during 3~4 seconds. Recovery time: 2 ±0.5h.
  • Ultrasonic cleaning may cause deterioration and destruction of the component. Please avoid ultrasonic cleaning.
  • Only leads of component may be soldered. Please avoid soldering another part of component. 100 120 140 160 180 200 220 240 260 280 100 120 140 160 180 200 220 240 260 280 300 320 340 360 Time (Sec) Temp ( Deg C)

SAW Bandpass Filters | Wireless Communications Issue: Rev 3, 11 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 5 of 6 www.rakonxpress.com Tape and reel specifications TAPE DETAILS: REEL DETAILS: Parameter Code Dimension Tolerance Height of component hole A 3.35 max Width of component hole B 3.35 max Diameter of sprocket hole D0 Φ 1.5 ± 0.1 Diameter of feed hole D1 Φ 1.5 ± 0.25 Pitch of sprocket hole P0 4.0 ± 0.2 Length from hole center to component center P1 8.0 ± 0.1 Length from Pocket hole center to sprocket hole center P2 2.0 ± 0.2 Width of carrier tape W 12.0 ± 0.3 Width of adhesive tape F 5.5 ± 0.3 Gap of hold down tape and carrier tape E 1.75 ± 0.1 Thickness of Ebossed tape sheet t1 0.31 max Thickness of Ebossed tape t2 1.7 max NOTE:  Unit: mm  Standard Packing Quantity (SPQ) is 1000 pieces/ reel Tape running direction W340 T632

  • AA Tape running direction

SAW Bandpass Filters | Wireless Communications Issue: Rev 3, 11 January 2023 Specifications are subject to change without notice Copyright © 2016 to 2023 Rakon Limited. All rights reserved Page 6 of 6 www.rakonxpress.com Reliability test Parameter Test condition / Description Thermal Shock The components shall remain within the electrical specifications after being kept at the condition of heat cycle conditions: TA=-40°C ±3°C, TB=85°C ±2°C, t1=t2=30min, switch time ≤3min & cycle time: 100 times, recovery time: 2h±0.5h. Temperature Storage High Temperature Storage: The components shall remain within the electrical specifications after being kept at the 85°C ±2°C for 500 hours, recovery time: 2h ±0.5h. Low Temperature Storage: The components shall remain within the electrical specifications after being kept at the -40°C ±3°C for 500 hours, recovery time: 2h ±0.5h. Humidity test The components shall remain within the electrical specifications after being kept at the condition of ambient temperature 60°C ±2°C, and 90~95% RH for 500 hours. Drop test The components shall remain within the electrical specifications after random free drops 10 times from height of 1.0 meter onto concrete floor, and the specimens shall meet the electrical specifications. Vibration Fatigue The components shall remain within the electrical specifications after loaded vibration at 10~55Hz, amplitude 1.5mm, X, Y, Z, direction, during 2 hours. Mechanical Shock The components shall remain within the electrical specifications after 1000 shocks, acceleration 392 m/s2 , duration 6ms. Note As a result of the particularity of inner structure of SAW products, the components can easily be breakdown by electrostatic shock; so it’s mandatory to pay attention to ESD protect during the tests.