TMXMT01

TMXMT01 RAKON | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 9

Technical content

Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved www.rakonxpress.com Table of Contents TMX MT01 SAW Filter datasheet 1.1 x 0.9 mm, SMD

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 1 of 8 www.rakonxpress.com

Features

Parameter Min. Typ. Max. Unit Storage temperature range (Tstg) -40 85 °C Operating temperature range (TA) -30 85 °C DC voltage (between any terminals) 10 V RF Power (in BandWidth) 13 dBm Frequency and Electrical Characteristics (Reference temperature @ 25°C) Parameter Min. Typ.1 Max. Unit Center frequency (fc) 1580 MHz Insertion Loss From 1559.09 to 1563.09 MHz From 1574.42 to 1576.42 MHz From 1597.55 to 1605.89 MHz 1.8 1.3 1.8 2.1 1.6 2.1 dB dB dB Passband Ripple From 1559.09 to 1563.09 MHz From 1574.42 to 1576.42 MHz From 1597.55 to 1605.89 MHz 0.2 0.2 0.3 0.5 0.4 0.6 dB dB dB VSWR Input From 1559.09 to 1563.09 MHz From 1574.42 to 1576.42 MHz From 1597.55 to 1605.89 MHz 1.5 1.25 1.55 1.9 1.8 1.9 VSWR Output From 1559.09 to 1563.09 MHz From 1574.42 to 1576.42 MHz From 1597.55 to 1605.89 MHz 1.25 1.555 1.9 1.8 1.9 Group delay Ripple From 1597.55 to 1605.89 MHz ns

1 Typical values are nominal performances at room temperature

Features Applications 1.1 x 0.9 mm  1580 MHz center frequency  Narrow and sharp passband characteristics  Low Insertion Loss and deep stopband attenuation for interference  High stability and reliability. No adjustment  Unbalanced to unbalanced operation  No matching network required for operation at 50 Ω  GNSS Receivers o Beidou o GPS o Glonass

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 2 of 8 www.rakonxpress.com Parameter Min. Typ.2 Max. Unit Absolute Attenuation From 10 to 960 MHz From 960 to 1463 MHz From 1710 to 1785 MHz From 1785 to 1990 MHz From 1990 to 2280 MHz From 2280 to 2400 MHz From 2400 to 2500 MHz From 2500 to 2700 MHz From 2700 to 3000 MHz From 3000 to 6000 MHz dB dB dB dB dB dB dB dB dB dB Input / Output impedance (Nominal) 50 Ω Test Circuit 50 Ω / 50 Ω Configuration SAW Filter Input Single, 50 Ω Output Single, 50 Ω GND 2, 3, 5

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 3 of 8 www.rakonxpress.com Model Outline, Pin Connection and Marking Pin Connections

1 Input unbalanced

4 Output unbalanced

2, 3, 5 To be grounded Marking Note Line 1 M1 RakonXpress designation (TMX MT01) Line 2 • DC • = Identify black dot DC = Date code (See the tables below) Year Code (1st digit) Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 2016 & 2020 n p q r s t u v w X y z 2017 & 2021 A B C D E F G H I K L M 2018 & 2022 N P Q R S T U V W X Y Z 2019 & 2023 a b c d e f g h i j k m Date Code (2nd digit) 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th 15th 16th A B C D E F G H J K L M N P Q R 17th 18th 19th 20th 21st 22nd 23rd 24th 25th 26th 27th 28th 29th 30th 31st S T U V W X Y Z a b d e f g h Unit: mm FRONT VIEW 0.65 max 0.9±0.05

• DC TOP VIEW 1.1±0.05 0.205±0.03 (x2) 0.18±0.03 (x5) BOTTOM VIEW 0.25±0.03 0.25±0.03 (x5)

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 4 of 8 www.rakonxpress.com Frequency Characteristics Parameters Graphs Typical S21 Response S11 Group Delay

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 5 of 8 www.rakonxpress.com Far Side ESD Protection This product is electrostatic sensitive device. When you install or measure it, you should be careful not to add antistatic electricity or high voltage. Please be advised that you had better check anti serge voltage. To reduce the probability of damages caused by ESD, the following matching topologies should be applied. MLC varistor + ESD matching Suppressor diode + ESD matching ESD matching” should be added to the filter port, where electrostatic discharge is expected. It predominantly appears at the antenna input of RF receivers. Therefore “ESD matching” should be designed to short circuit or block the ESD pulse. Depending on the input impedance of the SAW filter and the source impedance, the needed component values have to be determined from case to case.

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 6 of 8 www.rakonxpress.com In cases where ESD is minor, the following simplified “ESD matching” topologies can be used: Effectiveness of the applied ESD protection has to be checked according to relevant industry standards or customer specific requirements. Recommended Reflow Soldering Profile NOTE:

• The components shall remain within the electrical specifications after it soldered on the 1mm thickness PCB board and dipped in the solder at 260 ± 5°C during 10 ± 1 seconds.
• The components shall remain within the electrical specifications after it soldered by electric iron, solder at 350 ± 10 °C during 3~4 seconds. Recovery time: 2 ± 0.5 hour.
• Ultrasonic cleaning may cause deterioration and destruction of the component. Please avoid ultrasonic cleaning.
• Only leads of components may be soldered. Please avoid soldering another part of the component.

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 7 of 8 www.rakonxpress.com Tape and Reel Specifications TAPE DETAILS: REEL DETAILS: Parameter Code Dimension Tolerance Height of component hole A 1.02 ± 0.05 Width of component hole B 1.22 ± 0.05 Diameter of sprocket hole D0 Φ 1.55 ± 0.05 Diameter of feed hole D1 Φ 0.60 ± 0.05 Pitch of sprocket hole P0 4.0 ± 0.05 Length from hole center to component center P1 2.0 ± 0.05 Length from Pocket hole center to sprocket hole center P2 2.0 ± 0.05 Width of carrier tape W 6.0 ± 0.1 Width of adhesive tape F 3.50 ± 0.05 Gap of hold down tape and carrier tape E 1.75 ± 0.1 Thickness of Ebossed tape sheet t1 0.20 max ± 0.05 Thickness of Ebossed tape t2 0.72 max ± 0.05 NOTE:  Unit: mm  Standard Packing Quantity (SPQ) is 4000 pieces/ reel

• DC

SAW Bandpass Filters | GNSS Receivers Issue: Rev 1, 17 February 2023 Specifications are subject to change without notice Copyright © 2023 Rakon Limited. All rights reserved Page 8 of 8 www.rakonxpress.com Reliability Test Parameter Test condition / Description Mechanical shock (a) Drops: 3 times on concrete floor (b) Height: 1.0 m Vibration resistance (a) Frequency of vibration: 10~55Hz (b) Amplitude: 1.5 mm (c) Directions: X, Y and Z (d) Duration: 2 hours Moisture resistance (a) Condition: 40℃±2℃, 93+2 -3% RH (b) Duration: 96 hours (c) Wait 4 hours before measurement Climatic sequence (a) +70°C for 16 hours (b) +55°C for 24 hours, 90~9 5% RH (c) -25°C for 2 hours (d) +40°C for 24 hours, 90~95 % RH (e) Wait 4 hours before measurement High temperature exposure (a) Temperature: 85°C (b) Duration: 250 hours (c) Wait 4 hours before measurement Temperature cycling (a) +85°C for 30 minutes  -40°C for 30 minutes repeated 120 times (b) Wait 4 hours before measurement Note As a result of the particularity of inner structure of SAW products, the components can easily be breakdown by electrostatic shock; so it’s mandatory to pay attention to ESD protect during the tests.