TMR1302B MULTIDIMENSION | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
Datasheet V1.0a TMR1302B TMR Omnipolar Switch General Description The TMR 1302B is a digital omnipolar magnetic switch that integrates TMR and CMOS technology in order to provide a magnetically triggered digital switch with high sensitivity, high speed, and ultra -low power consumption. It integrates a push -pull half-bridge TMR magnetic sensor and CMOS sign al processing circuitry within the same package. Designed for use in applications that are both power-critical and performance-demanding, this device includes an on-chip TMR voltage generator for precise magnetic sensing, TMR voltage amplifier and comparat or, a Schmitt trigger to provide switching hysteresis for noise rejection, and CMOS push -pull output. An internal band gap regulator is used to provide temperature compensated supply voltage for internal circuits, and it allows a wide range of operating supply voltages. The TMR1302B draws only 1.5μA resulting in ultra-low power operation, additionally it has fast response, accurate switching points, excellent thermal stability, and immunity to stray field interference. It is available in two packaging form factors:SOT23-3 (P/N TMR1302BS), or TO-92S(P/N TMR1302BT). Features and Benefits Tunneling Magnetoresistance (TMR) Technology Ultra Low Power Consumption at 1.5uA High Frequency Response at 1kHz Operation with North or South Pole Low Operate Points for High Sensitivity Compatible with a Wide Range of Supply Voltages Excellent Thermal Stability High Tolerance to External Magnetic Field Interference
Applications
Utility Meters including Water, Gas, and Heat Meters Proximity Switches Speed Sensing Rotary and Linear Position Sensing TMR1302BS(Left), TMR1302BT(Right) Block Diagram
Datasheet V1.0a Pin Configuration Pin Name Pin No. Pin Function TO-92S SOT23-3 VOUT 1 2 Output GND 2 3 Ground VCC 3 1 Supply Voltage SOT23-3 TO-92S Absolute Maximum Ratings Parameter Symbol Limit Unit Supply Voltage VCC 7 V Reverse Supply Voltage VRCC 0.3 V Output Current IOUTSINK 9 mA Magnetic Flux Density B 2800 G ESD level(HBM) VESD 4 kV Operating Ambient Temperature TA -40 ~125 °C Storage Temperature Tstg -50 ~ 150 °C Electrical Characteristics (VCC=3.0V, TA=25°C) Parameter Symbol Conditions Min Typ. Max Unit Supply Voltage VCC Operating 1.8 3.0 5.5 V Output High Voltage VOH Vcc-0.3 Vcc V Output Low Voltage VOL 0 0.2 V Supply Current ICC Output Open 1.5 μA Response Frequency F 1000 Hz Note: a 100nF capacitor is connected between VCC and GND during all tests in the above table. Magnetic Characteristics (VCC = 3.0V, TA = 25°C) Parameters Symbol Min Typ. Max Units Operate Point BOPS 17 G BOPN -17 G Release Point BRPS 13.5 G BRPN -13.5 G Hysteresis BH 3.5 G
Datasheet V1.0a Voltage and Temperature Characteristics Output Behavior vs. Magnetic Pole Parameter Test Conditions Output South Pole B > BOPS Low (On) 0< B < BRPS High (Off) North Pole B < BOPN Low (On) 0 > B > BRPN High (Off) Note: when power is turned on under zero magnetic field, the output is “High”. Sensing Direction of Magnetic Field Magnetic Flux
Application Information
The output of the TMR1302B switches low (turns on) when a magnetic field parallel to the TMR sensor exceeds the operate point threshold, BOP. When the magnetic field is reduced below the release point, BRP, the device output goes high (turns off). The difference between the magnetic operate point and release point is the hysteresis BH of the device. It is strongly recommended that an external bypass capacitor be connected in close proximity to the device between the supply and ground to reduce noise. The typical value of the external capacitor is 0.1μF.
Datasheet V1.0a
Package Information
Top view and side view (unit: mm)
Datasheet V1.0a MultiDimension Technology Co., Ltd. Address:No.7 Guangdong Road, Zhangjiagang Free Trade Zone, Jiangsu, 215634, China Web: www.dowaytech.com/en Email: info@dowaytech.com The information provided herein by MultiDimension Technology Co., Ltd. (hereinafter MultiDimension) is believed to be accurate and reliable. Publication neither conveys nor implies any license under patent or other industrial or intellectual property rights. MultiDi mension reserves the right to make changes to product specifications for the purpose of improving product quality, reliability, and functionality. MultiDimension does not assume any liability arising out of the application and use of its products. MultiDimension’s customers using or selling this product for use in appliances, devices, or systems where malfunction can reasonably be expected to result in personal injury do so at their own risk and agree to fully indemnify MultiDimension for any damages resulting from such applications.