TMM TRANSKO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 7

Technical content

Transko Electronics, Inc. 3981 E. Miraloma Ave. Anaheim, CA 92806 USA Tel: 714-528-8000 Fax: 714-528-8017 Website: www.transko.com E-mail: sales@transko.com RoHS Compliant Rev 3: 06-27-2022 MEMS OSCILLATOR ■ FEATURES ■ APPLICATIONS

  • Output frequency from 1M~137MHz • DSC, DVC, DVR, IP CAM, SSD, GPON, EPON, USB
  • Low power consumption of 3.5 mA typical at 1.8V • SATA, SAS, Firewire, 100M / 1G / 10G Ethernet
  • Available LVCMOS/HCMOS outputs • Tablets, e-Books
  • RoHS and REACH compliant, Pb-free, Halogen-free and Antimony-free
  • All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise stated.
  • Typical values are at 25°C and nominal supply voltage. Parameters Symbol Min. Typ. Max. Unit Condition Frequency Range Output Frequency Range 137 Frequency Stability and Aging Frequency Stability F_stab -20 +20 Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and variations over operating temperature, rated power supply voltage and load. -25 +25 -50 +50 Operating Temperature Range Operating Temperature Range T_use -20 +70 Extended Commercial -40 +85 Industrial Supply Voltage and Current Consumption Supply Voltage Vdd 1.62 1.8 1.98 2.25 2.5 2.75 2.52 2.8 3.08 2.7 3.0 3.3 2.97 3.3 3.63 2.25 3.63 Current Consumption Idd 3.8 4.5 mA No load condition, f = 20 MHz, Vdd = 2.8V to 3.3V 3.7 4.2 mA No load condition, f = 20 MHz, Vdd = 2.5V 3.5 4.1 mA No load condition, f = 20 MHz, Vdd = 1.8V OE Disable Current I_OD 4.2 mA Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z state 4.0 mA Vdd = 1.8V, OE = GND, Output in high-Z state Standby Current I_std 2.1 4.3 A 1.1 2.5 A 0.2 1.3 A LVCMOS Output Characteristics Duty Cycle DC 55 % All Vdds. See Waveform figure Rise/Fall Time Tr, Tf Vdd = 2.5V, 2.8V, 3.0V or 3.3V, 20% - 80% Output High Voltage VOH Vdd IOH = -4 mA (Vdd = 3.0V or 3.3V) IOH = -3 mA (Vdd = 2.8V and Vdd = 2.5V) IOH = -2 mA (Vdd = 1.8V) Output Low Voltage VOL Vdd IOL = 4 mA (Vdd = 3.0V or 3.3V) IOL = 3 mA (Vdd = 2.8V and Vdd = 2.5V) IOL = 2 mA (Vdd = 1.8V) Input Characteristics Input High Voltage VIH Vdd Input Low Voltage VIL Vdd Input Pull-up Impedance Z_in 87 k Startup and Resume Timing Startup Time T_start ms Measured from the time Vdd reaches its rated minimum value Enable/Disable Time T_oe f = 110 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles Resume Time T_resume ms Jitter 1.8 f = 75 MHz, Vdd = 1.8V Peak-to-peak Period Jitter T_pk 12 25 f = 75 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V 14 30 f = 75 MHz, Vdd = 1.8V RMS Phase Jitter (random) T_phj 0.5 0.9 f = 75 MHz, Integration bandwidth = 900 kHz to 7.5 MHz 1.3 f = 75 MHz, Integration bandwidth = 12 kHz to 20 MHz ■ ELECTRICAL CHARACTERISTICS

Transko Electronics, Inc. 3981 E. Miraloma Ave. Anaheim, CA 92806 USA Tel: 714-528-8000 Fax: 714-528-8017 Website: www.transko.com E-mail: sales@transko.com RoHS Compliant Rev 3: 06-27-2022 Parameter Min. Max. Unit Storage Temperature 150 °C Vdd -0.5 Electrostatic Discharge 2000 Soldering Temperature (follow standard Pb free soldering guidelines) 260 °C Junction Temperature 150 °C ■ ABSOLUTE MAXIMUM LIMITS Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings. Pin 1 Configuration Options (OE, , or NC) Pin 1 can be factory-programmed to support three modes: Output Enable (OE), Standby ( ) or No Connect (NC). Output Enable (OE) Mode In the OE mode, applying logic Low to the OE pin only disables the output driver and puts it in Hi-Z mode. The core of the device continues to operate normally. Power consumption is reduced due to the inactivity of the output. When the OE pin is pulled High, the output is typically enabled in <1 μs. Standby ( ) Mode In the ST mode, a device enters into the standby mode when Pin 1 pulled Low. All internal circuits of the device are turned off. The current is reduced to a standby current, typically in the range of a few μA. When is pulled High, the device goes through the “resume” process, which can take up to 5 ms. No Connect (NC) Mode In the NC mode, the device always operates in its normal mode and outputs the specified frequency regardless of the logic level on pin 1. ■ PIN DESCRIPTION 2. A capacitor of value 0.1 µF or higher between Vdd and GND is required Pin Symbol Function Output Enable H[1]: specified frequency output L: output is high impedance. Only output driver is disabled. Standby H[1]: specified frequency output L: output is low (weak pull down). Device goes to sleep mode. Supply current reduces to I_std. No Connect Any voltage between 0 and Vdd or Open[1]: Specified frequency output. Pin 1 has no function. GND Power Electrical ground OUT Output Oscillator output VDD Power Power supply voltage[2] ■ PIN ASSIGNMENTS OE/ST/NC OE NC Active current 20 MHz (max, 1.8V) 4.1 mA 4.1 mA 4.1 mA OE disable current (max. 1.8V) 4 mA N/A Standby current (typical 1.8V) 0.6 µA N/A OE enable time at 77.76 MHz (max) 138 ns N/A Resume time from standby (max, all frequency) 5 ms N/A Output driver in OE disable/standby mode High Z weak N/A

Transko Electronics, Inc. 3981 E. Miraloma Ave. Anaheim, CA 92806 USA Tel: 714-528-8000 Fax: 714-528-8017 Website: www.transko.com E-mail: sales@transko.com RoHS Compliant Rev 3: 06-27-2022 ■ PERFORMANCE PLOTS All plots are measured with 15 pF load at room temperature, unless otherwise stated. Phase noise plots are measured with Agilent E5052B signal source analyzer. Integration range is up to 5 MHz for carrier frequ encies below 40 MHz. ■ TEST CIRCUIT ■ WAVEFORM Duty Cycle is computed as Duty Cycle = TH/Period. ■ TIMING DIAGRAMS OE Disable Timing (OE Mode Only) OE Enable Timing (OE Mode Only) Startup Timing (OE / ST Mode) Standby Resume Timing ( ST Mode Only) Idd vs Frequency Frequency vs Temperature

Transko Electronics, Inc. 3981 E. Miraloma Ave. Anaheim, CA 92806 USA Tel: 714-528-8000 Fax: 714-528-8017 Website: www.transko.com E-mail: sales@transko.com RoHS Compliant Rev 3: 06-27-2022 RMS Period Jitter vs Frequency Duty Cycle vs Frequency RMS Period Jitter vs Frequency Duty Cycle vs Frequency RMS Integrated Phase Jitter Random (12 kHz to 20M Hz) vs Frequency RMS Integrated Phase Jitter Random (900 kHz to 20 MHz) vs Frequency

Transko Electronics, Inc. 3981 E. Miraloma Ave. Anaheim, CA 92806 USA Tel: 714-528-8000 Fax: 714-528-8017 Website: www.transko.com E-mail: sales@transko.com RoHS Compliant Rev 3: 06-27-2022 Note: Consult factory for detail Soldering 255 ±5°C 150 ±5°C Pre-heating <10 Sec <120 Sec 170 ±5°C ■ REFLOW PROFILE Parameter Condition / Test Method Mechanical Shock MIL-STD-883F, Method2002 Mechanical Vibration MIL-STD-883F, Method 2007 Temperature Cycle JESD22, Method A104 Solderability MIL-STD-883F, Method2003 Moisture Sensitivity Level MSL1 @ 260°C ■ ENVIRONMENTAL COMPLIANCE ■ OUTPUT DRIVE STRENGTH—RISE / FALL TIME OPTIONS Rise/Fall Time Typ (ns) Vdd = 1.8V Drive Strength \\ CLOAD 5 pF 15 pF 30 pF 45 pF 60 pF Rise/Fall Time Typ (ns) Vdd = 2.5V Drive Strength \\CLOAD 5 pF 15 pF 30 pF 45 pF 60 pF Rise/Fall Time Typ (ns) Vdd = 2.8V Drive Strength \\ CLOAD 5 pF 15 pF 30 pF 45 pF 60 pF Rise/Fall Time Typ (ns) Vdd = 3.0V Drive Strength \\ CLOAD 5 pF 15 pF 30 pF 45 pF 60 pF Rise/Fall Time Typ (ns) Vdd = 3.3V Drive Strength \\ CLOAD 5 pF 15 pF 30 pF 45 pF 60 pF

Transko Electronics, Inc. 3981 E. Miraloma Ave. Anaheim, CA 92806 USA Tel: 714-528-8000 Fax: 714-528-8017 Website: www.transko.com E-mail: sales@transko.com RoHS Compliant Rev 3: 06-27-2022 A capacitor of value 0.1 μF or higher between Vdd and GND is required. MARKING A = FACTORY CODE Y = FACTORY CODE XXXX = LOT CODE O = PIN 1 LOCATION ■ PACKAGE OPTIONS / LAND PATTERN (Unit:mm) PACKAGE 21 PACKAGE 22 PACKAGE 32 PACKAGE 53 PACKAGE 75

Transko Electronics, Inc. 3981 E. Miraloma Ave. Anaheim, CA 92806 USA Tel: 714-528-8000 Fax: 714-528-8017 Website: www.transko.com E-mail: sales@transko.com RoHS Compliant Rev 3: 06-27-2022 Transko Electronics, Inc reserves the right to make changes to the product (s), service (s), and specification (s) described herein without notice. See “Terms of Sale” for details on our website. ■ PART NUMBERING GUIDE Product series TMM Package 21: 2.0 X 1.6 22: 2.5 X 2.0 32: 3.2 X 2.5 53: 5.0 X 3.2 75: 7.0 X 5.0 Stability 50: ± 50ppm 25: ± 25ppm 20: ± 20ppm XX: Two Digit Stability Tape and Reel TR: tape/reel Blank: Cut tape Supply Voltage 18: 1.8 Volt 25: 2.5 Volt 28: 2.8 Volt 30: 3.0 Volt 33: 3.3 Volt XX: 2.25V to 3.63V YY: 1.62V to 3.63V - up to 110MHz only Frequency M: MHz Pin 1 Option D: Output En/Disable S: Standby N: No Connect Operating Temperature C: -40 D: -35 E: -30 F: -20 G: -10 H: 0 J: 50 K: 60 M: 70 N: 75 P: 80 Q: 85 25.000M 32 TMM FM 33 TR 20 H Output Type H: HCMOS/LVCMOS Output Drive BLANK : Default or Select L A R B T E U F from Drive Table S