TLP114AIGM

TLP114AIGM TOSHIBA | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

TLP114A(IGM) 2002-09-25 1 TOSHIBA Photocoupler GaA ℓAs Ired + Photo−IC TLP114A(IGM) Transistor Invertor Inverter For Air Conditioner Line Receiver Ipm Interfaces The TOSHIBA mini flat coupler TLP114A is a small outline coupler, suitable for surface mount assembly. TLP114A consists of a high output power GaAℓAs light emitting diode, optically coupled to a high speed detector of one chip photo diode−transistor. TLP114A(IGM) has no internal base connection, and a faraday shield integrated on the photodetector chip provides an effective common mode noise transient immunity. TLP114A(IGM) guarantees minimum and maximum of propagation delay time, switching time dispersion, and high common mode transient immunity. There for TLP114A(IGM) is suitable for isolation interface between IPM(intelligent power module) and control IC circuits in motor control application. /G6c/G20Isolation voltage: 3750V rms(min.) /G6c/G20Common mode transient immunity : ±10kV/µs(min.) @V CM=1500V /G6c/G20Switching time: tpHL, tpLH=0.1µs(min.) =0.8µs(max.) @I F=10mA, VCC=15V, R L=20kΩ, Ta=25°C /G6c/G20Switching time dispersion: 0.7µs(max.) (|tpLH−tpHL|) /G6c/G20TTL compatible /G6c/G20UL recognized: UL1577, file no.E67349 Pin Configuration(top view) 1 : Anode 3 : Cathode 4 : Emitter (GND) 5 : Collector (Output) 6 : VCC SHIELD 3 4 Schematic VCC GND VO ICC IO 6 IF VF Shield TOSHIBA 11 −4C2 Weight: 0.09g Unit in mm TENTATIVE

TLP114A(IGM) 2002-09-25 2 Maximum Ratings(Ta = 25°C) Characteristic Symbol Rating Unit Forward current (Note 1) I F 20 mA Pulse forward current (Note 2) I FP 40 mA Peak transient forward current (Note 3) I FPT 1 A LED Reverse voltage V R 5 V Output current I O 8 mA Peak output current I OP 16 mA Output voltage V O /G2d0.5~20 V Supply voltage V CC /G2d0.5~30 V Detector Output power dissipation (Note 4) P O 100 mW Operating temperature range T opr /G2d55~100 °C Storage temperature range T stg /G2d55~125 °C Lead soldering temperature(10s) T sol 260 °C Isolation voltage(AC, 1min., R.H.≤60%, Ta=25°C) (Note 5) BV S 3750 Vrms (Note 1): Derate 0.36mA above 70°C. (Note 2): 50% duty cycle, 1ms pulse width. Derate 0.72mA / °C above 70°C. (Note 3): Pulse width PW ≤ 1µs, 300pps. (Note 4): Derate 1.8mW / °C above 70°C. (Note 5): Device considerd a two terminal device: pins1, 3 shorted together and pins4, 5, 6 shorted together.

TLP114A(IGM) 2002-09-25 3 Electrical Characteristics(Ta = 25°C) Characteristic Symbol Test Condition Min. Typ. Max. Unit Forward voltage V F IF=16mA 1.22 1.42 1.72 V Forward voltage temperature coefficient ∆VF / ∆Ta I F=16mA ― /G2d2 ― mV / °C Reverse current I R VR=3V ― ― 10 µA LED Capacitance between terminal CT V F=0, f=1MHz ― 30 ― pF IOH(1) IF=0mA, VCC=VO=5.5V ― 3 500 nA IOH(2) IF=0mA, VCC=30V VO=20V ― ― 5 High level output current IOH IF=0mA, VCC=30V VO=20V, Ta=70°C ― ― 50 µA High level supply current ICCH IF=0mA, VCC=30V ― 0.01 1 µA Supply voltage V CC ICC=0.01mA 30 ― ― V Detector Output voltage V O IO=0.5mA 20 ― ― V Coupled Electrical Characteristics(Ta = 25°C) Characteristic Symbol Test Condition Min. Typ. Max. Unit IF=10mA, VCC=4.5V VO=0.4V 25 35 75 Current transfer ratio I O / IF IF=16mA, VCC=4.5V VO=0.4V, Ta=/G2d25~100°C 15 ― ― Low level output voltage V OL IF=10mA, VCC=4.5V IO=2.4mA ― ― 0.4 V Isolation Characteristics(Ta = 25°C) Characteristic Symbol Test Condition Min. Typ. Max. Unit Capacitance input to output C S V=0, f=1MHz (Note 5) ― 0.8 ― pF Isolation resistance R S R.H.≤60%, VS=500V (Note 5) 5×1010 1014 ― Ω AC, 1 minute 3750 ― ― AC, 1 second, in oil ― 10000 ― Vrms Isolation voltage BV S DC, 1 minute, in oil ― 10000 ― Vdc

TLP114A(IGM) 2002-09-25 4 Switching Characteristics(Ta = 25°C, VCC = 15V) Characteristic Symbol Test Cir/G2d Cuit Test Condition Min. Typ. Max. Unit tpHL IF=0→ 10mA, RL=20kΩ 0.1 0.45 0.8 tpLH IF=0→ 10mA, RL=20kΩ Propagation delay time (H→ L) Propagation delay time (L→ H) I F=0→ 10mA, RL=20kΩ Ta=/G2d25~100°C 0.1 0.45 1.0 µs IF=10→ 0mA, RL=20kΩ ― 0.15 0.7 IF=10→ 0mA, RL=20kΩ Ta=0~85°C ― 0.25 0.8 Switching time dispersion between on and off pLH/G2dtpHL| IF=10→ 0mA, RL=20kΩ µs Common mode transient immunity at logic high output (Note 6) CM H IF=0mA VCM=1500Vp/G2dp RL=20kΩ 10000 15000 ― V / µs Common mode transient immunity at logic low output (Note 6) CM L IF=10mA VCM=1500Vp/G2dp RL=20kΩ /G2d10000 /G2d15000 ― V / µs (Note 6): CML is the maximum rate of fall of the common mode voltage that can be sustained with the output voltage in the logic low state (V O<1V). CM H is the maximum rate of rise of the common mode voltage that can be sustained with the output voltage in the logic high state (V O<4V). (Note 7): Maximum electrostatic discharge voltage for any pins: 100V (C=200pF, R=0). Test Circuit 1: Switching Time Test Circuit PW = 100µs Duty ratio = 1/10 IF monitor Pulse input Output monitor VO 0.1μF 100Ω VCC = 15V 3 4 6 RL VO IF 15V 1.5V VOL tpLH tpHL 1.5V

TLP114A(IGM) 2002-09-25 5 Test Circuit 2: Common Mode Noise Immunity Test Circuit /G29/G28 /G29/G28/G3d/G2c/G29/G28 /G29/G28/G3d µsft V1200 LCMµsrt V1200 HCM VO VCM 1500V 90% 15V VOL tr tf 10% VO (IF = 10mA) (IF = 0mA) IF Pulse gen ZO = 50Ω VCM Output monitor VO 0.1μF VCC = 5V 3 4 6 RL

TLP114A(IGM) 2002-09-25 6 /Gb7/G20TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. /Gb7/G20The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. /Gb7/G20Gallium arsenide (GaAs) is a substance used in the products described in this document. GaAs dust and fumes are toxic. Do not break, cut or pulverize the product, or use chemicals to dissolve them. When disposing of the products, follow the appropriate regulations. Do not dispose of the products with other industrial waste or with domestic garbage. /Gb7/G20The products described in this document are subject to the foreign exchange and foreign trade laws. /Gb7/G20The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. /Gb7/G20The information contained herein is subject to change without notice. 000707EBCRESTRICTIONS ON PRODUCT USE