TL071AC

TL071_96 TI | Alldatasheet

Document overview

• Manufacturer or author: pROVIDED bY alldatasheet.com(free datasheet download site)
• PDF pages: 14

Technical content

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 /C0068Low Power Consumption /C0068Wide Common-Mode and Differential Voltage Ranges /C0068Low Input Bias and Offset Currents /C0068Output Short-Circuit Protection /C0068Low Total Harmonic Distortion 0.003% Typ /C0068Low Noise Vn = 18 nV/√Hz Typ at f = 1 kHz /C0068High Input Impedance... JFET Input Stage /C0068Internal Frequency Compensation /C0068Latch-Up-Free Operation /C0068High Slew Rate...1 3 V /ms Typ /C0068Common-Mode Input Voltage Range Includes VCC+

description

The JFET-input operational amplifiers in the TL07_ series are designed as low-noise versions of the TL08_ series amplifiers with low input bias and offset currents and fast slew rate. The low harmonic distortion and low noise make the TL07_ series ideally suited for high-fidelity and audio preamplifier applications. Each amplifier features JFET inputs (for high input impedance) coupled with bipolar output stages integrated on a single monolithic chip. The C-suffix devices are characterized for operation from 0°C to 70°C. The I-suffix devices are characterized for operation from –40°C to 85°C. The M-suffix devices are characterized for operation over the full military temperature range of –55°C to 125°C. AVAILABLE OPTIONS PACKAGE TA VIOmax AT 25°C SMALL OUTLINE (D)† CHIP CARRIER (FK) CERAMIC DIP (J) CERAMIC DIP (JG) PLASTIC DIP (N) PLASTIC DIP (P) TSSOP PACKAGE (PW) FLAT PACKAGE (W) 10 mV TL071CD TL071CP TL071CPWLE10 mV 6 mV TL071CD TL071ACD — — — — TL071CP TL071ACP TL071CPWLE — — 3 mV TL071BCD TL071BCP — 0°Ct o 10 mV TL072CD TL072CP TL072CPWLE0°C to 70°C 10 mV 6 mV TL072CD TL072ACD — — — — TL072CP TL072ACP TL072CPWLE — —70°C 3 mV TL072BCD TL072BCP — 10 mV TL074CD TL074CN TL074CPWLE10 mV 6 mV TL074CD TL074ACD — — — TL074CN TL074ACN — TL074CPWLE — — 3 mV TL074BCD TL074BCN — 40°Ct o TL071ID — TL071IP–40°C to 85°C 6 mV TL071ID TL072ID — — — — TL071IP TL072IP — —85°C TL074ID TL074IN — 55°Ct o 6 mV TL071MFK — TL071MJG — — —–55°C to 125°C 6 mV — TL072MFK — TL072MJG — TL072MP — —125 C 9 mV TL074MFK TL074MJ — TL074MN — TL074MW † The D package is available taped and reeled. Add the suffix R to the device type (e.g., TL071CDR). The PW package is only available left-ended taped and reeled (e.g., TL072CPWLE). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  1996, Texas Instruments IncorporatedPRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

2IN– NC 1IN+ NC V CC+ NC 2IN+ NC VCC+ NC OUT NC 3212 0 1 9 91 0 1 1 1 2 1 3 NC 1IN– NC 1IN+ NC (TOP VIEW)NC 1OUT NC NC NC NC NC 2IN+ CC –V CC +V 1OUT 1IN– 1IN+ VCC + 2IN+ 2IN– 2OUT 4OUT 4IN– 4IN+ VCC – 3IN+ 3IN– 3OUT TL074, TL074A, TL074B D, J, N, OR PW PACKAGE TL074 ...W PACKAGE (TOP VIEW) NC – No internal connection 3212 0 1 9 91 0 1 1 1 2 1 3 NC IN– NC IN+ NC TL071 FK PACKAGE (TOP VIEW)NC OFFSET N1 NC NC NC NC NC OFFSET N2 NC CC –V TL072 FK PACKAGE 3212 0 1 9 91 01 11 21 3 4IN+ NC V CC – NC 3IN+ TL074 FK PACKAGE (TOP VIEW)1IN – 1OUT NC 3IN– 4IN – 2IN– NC 3OUT 4OUT 2OUT OFFSET N1 IN– IN+ VCC – NC V CC+ OUT OFFSET N2 TL071, TL071A, TL071B D, JG, P, OR PW PACKAGE (TOP VIEW) 1OUT 1IN– 1IN+ VCC – VCC + 2OUT 2IN– 2IN+ TL072, TL072A, TL072B D, JG, P, OR PW PACKAGE (TOP VIEW) symbols IN+ IN– OUT IN+ IN– OUT TL072 (each amplifier) TL074 (each amplifier) TL071 OFFSET N1 OFFSET N2

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 3POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 schematic (each amplifier) VCC+ IN + VCC– 1080 W ÎÎÎ 1080 W IN – TL071 Only 64 W 128 W 64 W All component values shown are nominal. ÁÁÁÁÁ Á ÁÁÁ Á ÁÁÁÁÁ OFFSET NULL (N1) ÁÁÁ Á Á Á ÁÁÁ OFFSET NULL (N2) OUT 18 pF COMPONENT COUNT † COMPONENT TYPE TL071 TL072 TL074 Resistors 11 22 44Resistors Transistors JFET 2 4 6 Diodes 1 2 4 Capacitors 1 2 4 epi-FET 1 2 4 † Includes bias and trim circuitry

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC– . 2. Differential voltages are at IN+ with respect to IN–. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR DERATE ABOVE T A TA = 70°C POWER RATING TA = 85°C POWER RATING TA = 125°C POWER RATING D (8 pin) 680 mW 5.8 mW/°C 33°C 465 mW 378 mW N/A D (14 pin) 680 mW 7.6 mW/ °C6 0 °C 604 mW 490 mW N/A FK 680 mW 11.0 mW/ °C8 8 °C 680 mW 680 mW 273 mW J 680 mW 11.0 mW/ °C8 8 °C 680 mW 680 mW 273 mW JG 680 mW 8.4 mW/ °C6 9 °C 672 mW 546 mW 210 mW N 680 mW 9.2 mW/ °C7 6 °C 680 mW 597 mW N/A P 680 mW 8.0 mW/ °C6 5 °C 640 mW 520 mW N/A PW (8 pin) 525 mW 4.2 mW/ °C7 0 °C 525 mW N/A N/A PW (14 pin) 700 mW 5.6 mW/ °C7 0 °C 700 mW N/A N/A W 680 mW 8.0 mW/°C 65°C 640 mW 520 mW 200 mW

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 POST OFFICE BOX 655303 DALLAS, TEXAS 75265• 5 electrical characteristics, VCC ± = ±15 V (unless otherwise noted) † ‡ TL071C TL071AC TL071BC TL071I PARAMETER TEST CONDITIONS † T ‡ TL071C TL072C TL071AC TL072AC TL071BC TL072BC TL071I TL072I UNITPARAMETER TEST CONDITIONS † TA ‡ TL074C TL074AC TL074BC TL074I UNIT MIN TYP MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX VIO Input offset voltageVO =0 R S =5 0W 25°C 3 10 3 6 2 3 3 6 mVVIO Input offset voltage VO = 0, R S = 50 W Full range 13 7.5 5 8 m V a VIO Temperature coefficient of input offset voltage VO = 0, R S = 50 W Full range 18 18 18 18 mV/°C IIO Input offset currentVO =0 25°C 5 100 5 100 5 100 5 100 pA IIO Input offset currentVO = 0 Full range 10 2 2 2 nA IIB Input bias current§ VO =0 25°C 65 200 65 200 65 200 65 200 pA IIB Input bias current§ VO = 0 Full range 7 7 7 20 nA Common mode –12 –12 –12 –12 VICR Common-mode input voltage range 25°C ±11 to ±11 to ±11 to ±11 to VICR input voltage range 15 15 15 15 Maximum peak R L = 10 kW 25°C ±12 ±13.5 ±12 ±13.5 ±12 ±13.5 ±12 ±13.5 VOM Maximum eak output voltage R L ≥ 10 kW Full range ±12 ±12 ±12 ±12 V swing R L ≥ 2 kW Full range ±10 ±10 ±10 ±10 AVD Large-signal differential voltageVO = ±10 V R L ≥ 2k W 25°C 25 200 50 200 50 200 50 200 V/mVAVD differential voltage amplification VO = ±10 V, R L ≥ 2 kW Full range 15 25 25 25 V/m V Unity-gain bandwidth 25°C 3 3 3 3 MHz ri Input resistance 25°C 1012 1012 1012 1012 W CMRR Common-mode VIC = VICRmin, 25°C 70 100 75 100 75 100 75 100 dBCMRR rejection ratio VO = 0, R S = 50 W 25°C 70 100 75 100 75 100 75 100 dB kSVR Supply-voltage rejection ratio VCC = ± 9 V to ± 15 V, 25°C 70 100 80 100 80 100 80 100 dBkSVR rejection ratio (DVCC ± /DVIO) VO = 0, R S = 50 W 25°C 70 100 80 100 80 100 80 100 dB ICC Supply current VO =0 No load 25°C 14 25 14 25 14 25 14 25 mAICC y VO1 /VO2 Crosstalk attenuation AVD = 100 25°C 120 120 120 120 dB † All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. ‡ Full range is TA = 0°C to 70°C for TL07_C,TL07_AC, TL07_BC and is TA = –40°C to 85°C for TL07_I. § Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in Figure 4. Pulse techniques must be used that maintain the junction temperature as close to the ambient temperature as possible.

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Figure 4. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible.

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996

8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

IIB Input bias current vs Free-air temperature 4 vs Frequency 5, 6, 7 VOM Maximum output voltage vs Frequency vs Free-air temperature 5, 6, 7 8VOM M aximum ou tput voltage vs Load resistance 9 vs Supply voltage 10 AVD Large signal differential voltage amplificationvs Free-air temperature 11AVD Large-signal differential voltage amplification vs Frequency 12 Phase shift vs Frequency 12 Normalized unity-gain bandwidth vs Free-air temperature 13 Normalized phase shift vs Free-air temperature 13 CMRR Common-mode rejection ratio vs Free-air temperature 14 ICC Supply current vs Supply voltage 15ICC Supply current yg vs Free-air temperature 16 PD Total power dissipation vs Free-air temperature 17 Normalized slew rate vs Free-air temperature 18 Vn Equivalent input noise voltage vs Frequency 19 THD Total harmonic distortion vs Frequency 20 Large-signal pulse response vs Time 21 VO Output voltage vs Elapsed time 22

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 9POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TYPICAL CHARACTERISTICS † Figure 4 IIB– Input Bias Current – nA TA – Free-Air Temperature – °C INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE IBI 0.1 0.01 100 –75 –50 –25 0 25 50 75 100 125 VCC ± = ± 15 V Figure 5 VCC ± = ± 5 V VCC ± = ± 15 V R L = 10 kW TA = 25°C See Figure 2 ± 15 ± 12.5 ± 10 ± 7.5 ± 5 ± 2.5 VOM – Maximum Peak Output Voltage – V f – Frequency – Hz 100 1 k 10 k 100 k 1 M 10 M MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY ÁÁÁ ÁÁÁ VOM ÎÎÎÎÎ ÎÎÎÎÎ VCC ± = ± 10 V Figure 6

10 M1 M100 k10 k1 k100

f – Frequency – Hz VOM – Maximum Peak Output Voltage – V ± 2.5 ± 5 ± 7.5 ± 10 ± 12.5 ± 15 See Figure 2 TA = 25°C R L = 2 kW VCC ± = ± 10 V VCC ± = ± 5 V MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY ÁÁ ÁÁ ÁÁ VOM ÎÎÎÎÎ ÎÎÎÎÎ VCC ± = ± 15 V Figure 7 ± 2.5 ± 5 ± 7.5 ± 10 ± 12.5 ± 15 10 k 40 k 100 k 400 k 1 M 4 M 10 M f – Frequency – Hz MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY VOM – Maximum Peak Output Voltage – V ÁÁÁ Á Á Á ÁÁÁ VOM VCC ± = ± 15 V R L = 2 kW See Figure 2 ÎÎÎÎ ÎÎÎÎ TA = –55°C ÎÎÎÎ ÎÎÎÎ TA = 25°C TA = 125°C † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996

10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS † Figure 8 –75 VOM – Maximum Peak Output Voltage – V TA – Free-Air Temperature – °C 125 ± 15 –50 –25 0 25 50 75 100 ± 2.5 ± 5 ± 7.5 ± 10 ± 12.5 R L = 10 kW VCC ± = ± 15 V See Figure 2 MAXIMUM PEAK OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE ÁÁ ÁÁ VOM ÎÎÎÎ ÎÎÎÎ R L = 2 kW Figure 9 0.1 R L – Load Resistance – kW ± 15 ± 2.5 ± 5 ± 7.5 ± 10 ± 12.5 VCC ± = ± 15 V TA = 25°C See Figure 2 0.2 0.4 0.7 1 2 4 7 MAXIMUM PEAK OUTPUT VOLTAGE vs LOAD RESISTANCE VOM – Maximum Peak Output Voltage – V ÁÁ ÁÁ VOM Figure 10 VOM – Maximum Peak Output Voltage – V |VCC ±| – Supply Voltage – V ± 15 2 4 6 8 10 12 14 ± 2.5 ± 5 ± 7.5 ± 10 ± 12.5 R L = 10 kW TA = 25°C MAXIMUM PEAK OUTPUT VOLTAGE vs SUPPLY VOLTAGE ÁÁ ÁÁ ÁÁ VOM Figure 11 –75 Voltage Amplification – V/mV TA – Free-Air Temperature – °C 125 1000 –50 –25 0 25 50 75 100 100 200 400 VCC ± = ± 15 V VO = ± 10 V R L = 2 kW LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE AVD – Large-Signal DifferentialA VD † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996 11POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TYPICAL CHARACTERISTICS † 45° 180° 135° 90° f – Frequency – Hz 10 M 106 10 100 1 k 10 k 100 k 1 M 101 102 103 104 105 Differential Voltage Amplification VCC ± = ± 5 V to ± 15 V R L = 2 kW TA = 25°C Phase Shift LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT vs FREQUENCY Voltage Amplification AVD – Large-Signal DifferentialA VD Phase Shift Figure 12 1.02 1.01 0.99 0.98 1.03 0.97 –75 0.7 Normalized Unity-Gain Bandwidth TA – Free-Air Temperature – °C 125 1.3 –50 –25 0 25 50 75 100 0.8 0.9 1.1

1.2 Unity-Gain Bandwidth

VCC ± = ± 15 V R L = 2 kW f = B1 for Phase Shift NORMALIZED UNITY-GAIN BANDWIDTH AND PHASE SHIFT vs FREE-AIR TEMPERATURE Normalized Phase Shift Phase Shift Figure 13 † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996

12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS † Figure 14 –75 CMRR – Common-Mode Rejection Ratio – dB TA – Free-Air Temperature – °C 125 –50 –25 0 25 50 75 100 VCC ± = ± 15 V R L = 10 kW COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE Figure 15 |VCC ±| – Supply Voltage – V 2 4 6 8 10 12 14 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 TA = 25°C No Signal No Load SUPPLY CURRENT PER AMPLIFIER vs SUPPLY VOLTAGE ICC – Supply Current Per Amplifier – mA ÁÁ ÁÁ CC ±I Figure 16 –75 TA – Free-Air Temperature – °C 125 –50 –25 0 25 50 75 100 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 VCC ± = ± 15 V No Signal No Load SUPPLY CURRENT PER AMPLIFIER vs FREE-AIR TEMPERATURE ICC – Supply Current Per Amplifier – mA ÁÁÁ Á Á Á ÁÁÁ CC ±I Figure 17 –75 TA – Free-Air Temperature – °C 125 250 –50 –25 0 25 50 75 100 100 125 150 175 200 225 VCC ± = ± 15 V No Signal No Load TL074 TL071 TOTAL POWER DISSIPATION vs FREE-AIR TEMPERATURE ÎÎÎ ÎÎÎ TL072 PD – Total Power Dissipation – mWPD † Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

TL071, TL071A, TL071B, TL072 TL072A, TL072B, TL074, TL074A, TL074B LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIERS SLOS080D – SEPTEMBER 1978 – REVISED AUGUST 1996

14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

10% VO – Output Voltage – mV t – Elapsed Time – ms 0.7 VCC ± = ± 15 V R L = 2 kW TA = 25°Ctr Overshoot 90% OUTPUT VOLTAGE vs ELAPSED TIME ÁÁÁ ÁÁÁ VO Figure 22