LEGK1 TM | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
TYPE T LEGIONELLA TEMPERATURE KIT WITH THERMOMETER, STANDARD PROBES AND ACCESSORIES MM2008 Thermometer
FEATURES
A single input thermocouple thermometer with an integral timer with a separate 1 minute and 2 minute count. This thermometer is primarily developed for use in Legionella risk management and offers reassurance that the correct reading is taken when monitoring hot and cold water temperatures. Single input thermocouple thermometer C/ F switchable Counter ensures that the correct temperature is met 1 minute counter for hot water temperatures 2 minute counter for cold water temperature Resolution of 0.1 to 1000 autoranging Switchable thermocouple K & T only Full retention of thermocouple type and temperature scale Auto Switch Off capability Easy to use software calibration Overrange / Open circuit sensor indication Low battery indication Supplied complete with shock resistant rubber boot IP67 casing USING THE TIMER 1. Press either for 1 minute count or for 2 minute count. 2. Press the same button again to switch off. SPECIFICATION Environmental AMBIENT OPERATING RANGE : -30 to 50 C STORAGE TEMPERATURE RANGE : -40 to 50 C HUMIDITY : 0 to 70% R.H. ELECTRICAL MEASUREMENT RANGES : K -200 to 1372 C T -200 to 400 C THERMOCOUPLE TYPES : K & T TEMPERATURE SCALES : C / F ACCURACY @23C : +/- 0.1% OF READING +/- 0.2 C CHARACTERISING ACCURACY : LESS THAN 0.05 C TEMPERATURE COEFFICIENT : 0.01% OF READING /C COLD JUNCTION COMPENSATION : 0.0075 C/C RESOLUTION : 0.1 to 1000, 1 ABOVE 1000
BATTERY : PP3 9V I.E.C. 6F22 BATTERY LIFE (INTERMITTENT USE) : GREATER THAN 200 HOURS (ALKALINE) WEIGHT : 155 gm DIMENSIONS : 130 X 70 X 33 mm Probes All probes are manufactured using: Type ‘T’ Thermocouple : ½ Class I (±0.25°C ±0.15%) Two stage moulding technique. Firstly the probes are encased in tough nylon, then a thermoplastic over moulding is applied. This gives an extremely robust and durable construction. Polypropylene Handles: Polypropylene is an extremely tough and durable material, commonly used for milk crates; it has good low temperature performance and a relatively high melt temperature. It performs exceptionally well under chemical attack Polypropylene Cable: Polyurethane cables are used in place of the standard PVC for the following reasons :- Greater retractability Enhanced memory of its curl Non–Toxic Greater mechanical strength for durability 12 X 0.2mm wires used internally for greater strength. PTFE inner insulation for strength and retractability. TS07 SPRUNG SHIELD SURFACE PROBE The probe is designed for the measurement of surface temperatures with wide temperature range. Construction Surface probe with sprung tip with thermocouple sensor attached with draught shield: Stainless Steel 316 (Food Grade). 2M curly polyurethane cable with moulded connector. WIDE AMBIENT TEMPERATURE SPECIFICATION : -30 TO 50 °C TIME RESPONSE (96% of valueon clean metal) : 3.0 Secs MEASUREMENT RANGE : -50 TO 400 °C TM03 TYPE ‘T’ GENERAL PURPOS/IMMERSION PROBE The probe is truly general purpose and may be used for gas, liquid or applications with difficult access. Construction Minerally Insulated Probe 3.0 mm Diameter by 100mm Long: Stainless Steel 316 (Food Grade). 2M curly polyurethane cable with moulded connector. Complete waterproof assembly. WIDE AMBIENT TEMPERATURE SPECIFICATION : -30 TO 50 °C
TIME RESPONSE (96%of value in water) : 2.0 Secs MEASUREMENT RANGE : -200 TO 400 °C TA01 FINE WIRE (PTFE) THERMOCOUPLE SENSOR This sensor is constructed using a 1M length PTFE wire constructed as a twisted pair. The wire used is ½ Class 1 Type T alloys (Cu / Co). A weld bead is manufactured at one end of the wire whilst the other end is terminated in a moulded miniature thermocouple plug. WIDE AMBIENT TEMPERATURE SPECIFICATION : -50 TO 50 °C TIME RESPONSE (96% of value in moving gas) : 0.1 Secs MEASUREMENT RANGE : -100 TO 250 °C Accessories TAPS – THERMOCOUPLE ATTACHMENT PADS TAPS are designed for use in attaching small diameter thermocouples, such as the TME Fine Wire Probes, to surfaces or pipes in hard to reach areas. Each kit contains a book of 20 Pads. The pads are manufactured from 0.120mm standard grade PTFE impregnated fibreglass with 0.050mm of high temperature silicone pressure sensitive adhesive. This product is almost chemically inert. Only molten alkali metals and fluorine under elevated temperatures and pressure will attack the PTFE surface. The fibreglass provides dimensional stability and restricts PTFE cold flow. The PTFE provides a non-stick / quick release surface in heat-sealing machines, plastic bag manufacturing and roll-can covering. Adhesion (oz/in width) 45 Break strength (lbs/in width) 120 Elongation (%) <5 Backing thickness (mm) 0.120 Adhesive thickness (mm) 0.050 Temperature range (C) -75 to +260 TAP Measurements approx. 17mm x 12mm (each) Operating Temperature Range -75 to +260°C TEMPRB Temperature log book for temperature record keeping. Eight page log book suitable for all temperature recording, and especially HACCP critical temperature record-keeping. LEGC01 Case The case measures: 34cm x 26cm x 6.5cm (approximate external) Holds up to:
- 1 x Handheld Thermometer
- 2 x Straight Handled Temperature Probes
- Fine Wire Probes
- 1 x spare battery
Cross-reference for compatible probes Suitable probes for use with this instrument TME PART No DESCRIPTION APPLICATION T/C TYPE KM08 LEGIONELLA SHOWER PROBE SHOWER/WATER TEMPERATURE K KS20-S HIGH SPEED REINFORCED DUAL SURFACE/IMMERSION PROBE FOR SURFACE AND IMMERSION MEASUREMENT K KPS10 PIPE CLAMP PROBE PROBE DESIGNED TO BE CLAMPED ONTO PIPES K KP05 NEEDLE PROBE CORE TEMPERATURE OF SEMI-SOLID MATERIAL K TP05 NEEDLE PROBE CORE TEMPERATURE OF SEMI-SOLID MATERIAL T KP07 NEEDLE PROBE HEAVY DUTY CORE TEMPERATURE OF SEMI-SOLID MATERIAL K TP07 NEEDLE PROBE HEAVY DUTY CORE TEMPERATURE OF SEMI-SOLID MATERIAL T KM01 LIGHT DUTY M.I. PROBE GENERAL PURPOSE LIQUID/GAS MEASUREMENT K TM01 LIGHT DUTY M.I. PROBE GENERAL PURPOSE LIQUID/GAS MEASUREMENT T KM03 M.I. PROBE GENERAL PURPOSE LIQUID/GAS MEASUREMENT K TM03 M.I. PROBE GENERAL PURPOSE LIQUID/GAS MEASUREMENT T KM04 M.I. PROBE EXTENDED LENGTH GENERAL PURPOSE LIQUID/GAS MEASUREMENT K TM04 M.I. PROBE EXTENDED LENGTH GENERAL PURPOSE LIQUID/GAS MEASUREMENT T KS01 SURFACE BAND PROBE FAST RESPONSE SURFACE MEASUREMENT K TS01-S DUAL PROBE FOR SURFACE AND IMMERSION MEASUREMENT T KS07 SURFACE PROBE GENERAL PURPOSE SURFACE MEASUREMENT K TS04 SURFACE PROBE GENERAL PURPOSE SURFACE MEASUREMENT T KS08 HIGH TEMP SURFACE PROBE HIGH TEMPERATURE SURFACE MEASUREMENT K KA04 AIR TEMPERATURE PROBE FAST RESPONSE AIR TEMPERATURE PROBE K TA04 AIR TEMPERATURE PROBE FAST RESPONSE AIR TEMPERATURE PROBE T TA12 SPATULA PROBE BETWEEN PACK PROBE T KH01 SOCKET IN HANDLE HANDLE FOR USE WITH PLUG MOUNTED PROBES K TH01 SOCKET IN HANDLE HANDLE FOR USE WITH PLUG MOUNTED PROBES T KHA02 PLUG MOUNTED AIR PROBE FAST RESPONSE AIR TEMPERATURE PROBE K THA2 PLUG MOUNTED AIR PROBE FAST RESPONSE AIR TEMPERATURE PROBE T KHM01 PLUG MOUNTED M.I. PROBE GENERAL PURPOSE LIQUID/GAS MEASUREMENT K THM01 PLUG MOUNTED M.I. PROBE GENERAL PURPOSE LIQUID/GAS MEASUREMENT T KHN01 PLUG MOUNTED NEEDLE PROBE CORE TEMPERATURE OF SEMI-SOLID MATERIAL K THN01 PLUG MOUNTED NEEDLE PROBE CORE TEMPERATURE OF SEMI-SOLID MATERIAL T THA12 PLUG MOUNTED SPATULA PROBE BETWEEN PACK PROBE T KHS01 PLUG MOUNTED SURFACE BAND PROBE FAST RESPONSE SURFACE MEASUREMENT K KHS02 PLUG MOUNTED SURFACE PROBE GENERAL PURPOSE SURFACE MEASUREMENT K THS02 PLUG MOUNTED SURFACE PROBE GENERAL PURPOSE SURFACE MEASUREMENT T PKHV1 HVAC KIT PROBE KIT DESIGNED FOR THE HVAC INDUSTRY K T PKGP1 GENERAL PURPOSE KIT PROBE KIT CONTAINING MOST POPULAR PROBES K