TEL0044

TEL0044 DFROBOT | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 10

Technical content

DFRduino GPS Shield‐LEA‐6H (SKU:TEL0044) Introduction The LEA-6H is a high performance stand-alone GPS and GALILEO receiver module designed to allow easy, straightforward migration from its LEA-4 predecessors. It features u-blox' KickStart weak signal acquisition technology, as well as flexible connectivity options. The LEA-6H comes with built- in Flash memory that enables firmware updates and the storage of specific configuration settings in a non-volatile RAM. The built-in antenna supervisor supports external and active antennas, such as u-blox' ANN high performance GPS antenna. u-blox KickStart provides accelerated startup at weak signals, and our featured SuperSense® Indoor GPS is capable of tracking and acquiring even extremely weak signals. This makes the LEA-6H suitable for solutions using small or covert antennas. Specification  Easy migration from LEA-4H and LEA-4P modules  Accelerated startup at weak signals thanks to KickStart Technology  Operating voltage: 2.7 - 3.6 V  LEA-6H Reference design documentation available with ceramic or GeoHelix antenna, UART and USB  2 Hz position update rate  Built-In Flash memory for fimware upgrades and storage of specific configuration settings

 Antenna supervisor and supply  Antenna short and open circuit detection and protection for external antennas  1 UART, 1 USB and 1 DDC (I2C compliant) interface  GALILEO-ready  50-channel u-blox 5 engine with over 1 million effective correlators  Under 1 second Time-To-First-Fix for Hot and Aided Starts  SuperSense® Indoor GPS: -160 dBm tracking sensitivity  Supports AssistNow Online and AssistNow Offline A-GPS services; OMA SUPL compliant  Supports SBAS (WAAS, EGNOS, MSAS, GAGAN)  Operating temperature range: -40 to 85°C  RoHS compliant (lead-free) Sample Code // # Editor : Lauren from DFRobot // # Product name: DFRduino GPS Shield-LEA-6H // # Product SKU : TEL0044 // # Version : 1.0 // # Update the library and sketch to compatible with IDE V1.0 and earlier // # Description: // # The sketch for using the DFRduino GPS Shield-LEA-6H // # Connection: // # Directly connect the shield to the Arduino controller // # If you'd like to drive the shield via UART interface, you may nee d to connect the jumpers on the board. // # #if defined(ARDUINO) && ARDUINO >= 100 #include "Arduino.h" #define WireSend(args) Wire.write(args) #define WireRead(args) Wire.read(args) #define printByte(args) Serial.write(args) #define printlnByte(args) Serial.write(args),Serial.println()

#else #include "WProgram.h" #define WireSend(args) Wire.send(args) #define WireRead(args) Wire.receive(args) #define printByte(args) Serial.print(args,BYTE) #define printlnByte(args) Serial.println(args,BYTE) #endif #include <Wire.h> #define BUFFER_LENGTH 10//Define the buffer length int GPSAddress = 0x42;//GPS I2C Address double Datatransfer(char *data_buf,char num)//Data type converter：convert cha r type to float { //*data_buf:char data array ;num: float length double temp=0.0; unsigned char i,j; if(data_buf[0]=='-')//The condition of the negative i=1; //The date in the array is converted to an integer and accumulative while(data_buf[i]!='.') temp=temp*10+(data_buf[i++]-0x30); for(j=0;j<num;j++) temp=temp*10+(data_buf[++i]-0x30); //The date will converted integer transform into a floating point number for(j=0;j<num;j++) temp=temp/10; //Converted to a negative number temp=0-temp;

i=0; while(data_buf[i]!='.') temp=temp*10+(data_buf[i++]-0x30); for(j=0;j<num;j++) temp=temp*10+(data_buf[++i]-0x30); for(j=0;j<num;j++) temp=temp/10 ; return temp; void rec_init()//initial GPS Wire.beginTransmission(GPSAddress); WireSend(0xff);//To send data address Wire.endTransmission(); Wire.beginTransmission(GPSAddress); Wire.requestFrom(GPSAddress,10);//Require 10 bytes read from the GPS device char ID()//Receive the statement ID char i = 0; char value[7]={ '$','G','P','G','G','A',',' };//To receive the ID content of GPS sta tements char buff[7]={ while(1) rec_init();//Receive data initialization

while(Wire.available()) buff[i] = WireRead();//Receive serial data if(buff[i]==value[i])//Contrast the correct ID i++; if(i==7) Wire.endTransmission();//End of receiving return 1;//Receiving returns 1 else i=0; Wire.endTransmission();//End receiving void UTC()//Time information char i = 0,flag=0; char value[7]={ char buff[7]={ char time[9]={ '0','0','0','0','0','0','0','0','0' };//Storage time data double t=0.0; while(1) rec_init();

while(Wire.available()) if(!flag) buff[i] = WireRead(); if(buff[i]==value[i]) i++; if(i==7) i=0; flag=1; else i=0; else time[i] = WireRead(); i++; if(i==9) t=Datatransfer(time,2);//Converts floating-point data t=t+80000.00;//To convert time to Beijing time Serial.println(t);//The time data output Wire.endTransmission(); return; Wire.endTransmission();

void rec_data(char *buff,char num1,char num2)//Receive data function { //*buff：Receive data array；num1：Number of commas ； num2：The length of the array char i=0,count=0; if(ID()) while(1) rec_init(); while(Wire.available()) buff[i] = WireRead(); if(count!=num1) if(buff[i]==',') count++; else i++; if(i==num2) Wire.endTransmission(); return; Wire.endTransmission(); void latitude()//Latitude information

char lat[10]={ '0','0','0','0','0','0','0','0','0','0' };//Store the latitude data rec_data(lat,1 ,10);//Receive the latitude data Serial.println(Datatransfer(lat,5),5);//output void lat_dir()//Latitude direction information char dir[1]={'0'};//Store latitude direction data rec_data(dir,2,1);//Receive latitude direction data printlnByte(dir[0]);//output latitude direction information void longitude()//Longitude information char lon[11]={ '0','0','0','0','0','0','0','0','0','0','0' };//Store longitude data rec_data(lon,3,11);//Receive the longitude data Serial.println(Datatransfer(lon,5),5);//out put date void lon_dir()//Longitude direction information char dir[1]={'0'}; rec_data(dir,4,1); printlnByte(dir[0]);//output latitude direction information void altitude()//Altitude information char i=0,count=0; char alt[8]={ if(ID())

while(1) rec_init(); while(Wire.available()) alt[i] = WireRead(); if(count!=8) if(alt[i]==',') count++; else if(alt[i]==',') Serial.println(Datatransfer(alt,1),1); Wire.endTransmission(); return; else i++; Wire.endTransmission(); void setup() Wire.begin();//IIC Initialize Serial.begin(9600);//set baud rate Serial.println("DFRobot DFRduino GPS Shield v1.0"); Serial.println("$GPGGA statement information: ");

void loop() while(1) Serial.print("UTC:"); UTC(); Serial.print("Lat:"); latitude(); Serial.print("Dir:"); lat_dir(); Serial.print("Lon:"); longitude(); Serial.print("Dir:"); lon_dir(); Serial.print("Alt:"); altitude(); Serial.println(' '); Serial.println(' '); Notice:When you use above code.Please unplug the jumper caps before you upload the code to Arduino.And when it has been finished, don't forget to plug it back. Powered By DFRobot © 2008-2016