TCA1A225M8R

TC_A_11 ROHM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

1/7 www.rohm.com ○c 2011 ROHM Co., Ltd. All rights reserved. 2011.06 - Rev.F Chip tantalum capacitors TC Series A Case Features (A) Dimensions (Unit : mm) 1) Vital for all hybrid integrated circuits board application. 2) Wide capacitance range. 3) Screening by thermal shock. Part No. Explanation M0 J 8 RT 1 0 6C A Rated voltage Capacitance tolerance Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. 8 : Reel width : 8mm R : Positive electrode on the side opposite to sprocket hole 1 3 642 5

11 Series name

2 Case style

4 Nominal capacitance

20%M : +− CODE 6.3 20 35 1D 1V Rated voltage (V) TC A Dimensions L H S SS W H L W Anode mark (Unit : mm) 3.2 0.2+− 1.6 0.2+− 1.2 0.2+− 1.6 0.2+− 0.8 0.3+ A case + −

2/7 www.rohm.com ○c 2011 ROHM Co., Ltd. All rights reserved. 2011.06 - Rev.F Data Sheet TC Series A Case  Rated table (μF) Rated voltage (V) 1 (105) A 1.5 (155) A 2.2 (225) A 3.3 (335) A A A A A A A A A 4.7 (475) A 6.8 (685) A A A A A10 (106) A A A A A A A A A AA A A 15 (156) A 22 (226) A A A A 33 (336) 47 (476) 68 (686) 100 (107) 150 (157) A A A A 6.3 Remark) Case size codes (A) in the above show products line-up. ∗ Under development A A A  Marking j aj a The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : Due to the small size of A case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Voltage Code Rated DC Voltage (V) g j A C D V 6.3 E2 5 Capacitance Code Nominal Capacitance (μF) A E J N S W a e j n 1.0 1.5 2.2 3.3 4.7 6.8 s4 7 w6 8 100 [A case] note 1) note 2) voltage code and capacitance code are variable with parts number −(1) j −(2) a a

3/7 www.rohm.com ○c 2011 ROHM Co., Ltd. All rights reserved. 2011.06 - Rev.F Data Sheet TC Series A Case  Characteristics Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Operating Temperature −55°C~+125°C Maximum operating temperature with no voltage derating +85°C Rated voltage (VDC) 20 25 16106.34 Category voltage (VDC) 13 16 106.342.5 Surge voltage (VDC) 13 852 6 20 32 DC Leakage current 0.5 μA or 0.01CV whichever is greater Shown in " Standard list " Capacitance tolerance Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Tangent of loss angle (Df, tan δ) Impedance Resistance to Soldering heat Temperature cycle Moisture resistance There should be no significant abnormality. The indications should be clear. Appearance ΔC / C Df (tan δ) L.C. Shall be satisfied the voltage on " Standard list " Measuring frequency : 120 ±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Shall be satisfied the voltage on " Standard list " at 85°C at 125°C at 85°C Voltage : Rated voltage for 1min Shall be satisfied allowance range. ±20% Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Less than initial limit Voltage reduction when temperature exceeds +85°C As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 260±10°C Duration : 5±0.5s Repetition : 1 After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 Others : Within ±5% of initial value There should be no significant abnormality. The indications should be clear. Appearance ΔC / C Df (tan δ) L.C. Less than initial limit After leaving the sample under such atmospheric condition that the temperature and humidity are 60±2°C and 90 to 95% RH,respectiveiy, for 500±12h leave it at room temperature for over 24h and then measure the sample. TCA0G686M8R : Within ±15% of initial value TCA0G107M8R : Within ±20% of initial value Others : Within ±10% of initial value Others : Within ±10% of initial value Others : Less than initial limit There should be no significant abnormality. The indications should be clear. Appearance ΔC / C Df (tan δ) L.C. Less than initial limit Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. Less than initial limit TCA0G686M8R : Within ±15% of initial value Temp. Time Room temp. Room temp. 3min.or less 3min.or less 30±3min. 30±3min. −55 3°C+− 125 2°C+− TCA0G686M8R : Within ±15% of initial value TCA0G107M8R : Within ±20% of initial value TCA0G107M8R : Within ±20% of initial value TCA0J476M8R : Within ±15% of initial value TCA0G686M8R : Less than 150% of initial limit TCA0G107M8R : Less than 150% of initial limit After the specimens, leave it at room temperature for over 24h and then measure the sample. TCA1A226M8R : Within ±15% of initial value TCAP0J226 : Less than 150% of initial limit Others : Less than initial limit

4/7 www.rohm.com ○c 2011 ROHM Co., Ltd. All rights reserved. 2011.06 - Rev.F Data Sheet TC Series A Case Item Performance Test conditions (based on JIS C 5101−1 and JIS C 5101− 3) Temperature Stability Surge voltage Shall be satisfied the voltage on " Standard list " As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 Temp. Appearance There should be no significant abnormality. Temp. −55°C +85°C Df (tan δ) L.C. L.C. Less than 1000% of initial limit Shall be satisfied the voltage on " Standard list "Df (tan δ) Shall be satisfied the voltage on " Standard list "Df (tan δ) L.C. Less than 1250% of initial limit Temp. +125°C ΔC / C Within 0/−12% of initial value ΔC / C Within +15/0% of initial value ΔC / C Others : Within +10/0% of initial value Loading at High temperature ΔC / C Df (tan δ) L.C. L.C. Shall be satisfied the voltage on " Standard list " Less than initial limit After applying the rated voltage for 2000+72/0 h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature / humidity for over 24h and measure the value. As per 4.26JIS C 5101-1 As per 4.14JIS C 5101-3 Apply the specified surge voltage via the serial resistance of 1kΩ every 5±0.5 min. for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. Df (tan δ) Less than initial limit Others : ±10% of initial value ΔC / C TCA0G686M8R : Within ±15% of initial value TCA0G107M8R : Within ±20% of initial value TCA0J476M8R : Within ±15% of initial value There should be no significant abnormality.Appearance There should be no significant abnormality.Appearance Terminal strength The measured value should be stable. A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below) Capacitance F (Apply force) (Unit : mm) R230 45 45 thickness=1.6mm TCA0G686M8R : Within +12/0% of initial value TCA0G107M8R : Within +12/0% of initial value TCA0G686M8R : Within ±15% of initial value TCA0G686M8R : Less than 125% of initial limit TCA0G107M8R : Less than 125% of initial limit TCA1A226M8R : Less than 125% of initial limit TCA1E105M8R : Less than 125% of initial limit TCA1A226M8R : Within ±15% of initial value TCA0G107M8R : Within ±20% of initial value Others : Within±10% of initial value Others : Less than initial limit

5/7 www.rohm.com ○c 2011 ROHM Co., Ltd. All rights reserved. 2011.06 - Rev.F Data Sheet TC Series A Case Item Performance Test conditions (JIS C 5101−1 and JIS C 5101− 3) Adhesiveness Dimensions The terminal should not come off. As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. Apply force a circuit board product ja Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed=25±2.5mm / s Pre−treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25% IPA 75% CapacitanceVibration Appearance Measure value should not fluctuate during the measurement. There should be no significant abnormality. As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board

6/7 www.rohm.com ○c 2011 ROHM Co., Ltd. All rights reserved. 2011.06 - Rev.F Data Sheet TC Series A Case  Standard products list, TC series A case 22 0.9 33 1.3 1.9 2.7 0.53.3 1.5 0.5 0.5 0.5 15 0.6 TC A 0G 475M8R TC A 0G 106M8R TC A 0G 156M8R TC A 0G 226M8R TC A 0G 336M8R TC A 0G 476M8R TC A 0G 686M8R TC A 0J 335M8R 4.7 TC A 0G 685M8R 6.8 TC A 0J 475M8R 4.7 2.2 TC A 0J 685M8R TC A 0J 106M8R 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 4 2.5 5 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 6.3 4 8 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 10 6.3 13 16 10 20 16 10 20 16 10 20 6.8 3.3 4.7 0.5 15TC A 0J 156M8R TC A 0J 226M8R 22 3.0 0.7 TC A 0J 336M8R TC A 0J 476M8R TC A 1A 155M8R TC A 1A 225M8R TC A 1A 335M8R TC A 1A 475M8R TC A 1A 685M8R 33 2.1 0.9 6.8 10 6 812 10 812 10 812 10 812 10 812 10 0.5 8 12 10 812 10 812 10 0.5 6 10 8 0.5 6 10 8 0.5 8 12 10 0.5 3.5 3.2 5.6 4.9 5.6 4.9 4.2 3.5 3.2 3.2 8.8 5.6 4.9 812 10 4.2 812 10 4 812 10 3 1014 12 3.5 1230 16 3.2 4.2 20+− 20+− 20+− 20+− 20+− 20+− 20+− 100 4TC A 0G 107M8R 4 2.5 5 30 54 36 320+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 20+− 1.0TC A 1A 106M8R 10 1.5TC A 1A 156M8R 15 2.2 610 8 70.5 610 8 5.60.5 20+− 20+− 20+− 20+− 20+− 610 8 4.90.5 610 8 4.8 610 8 3.9 610 8 3.8 812 10 3.5 0.5 TC A 1A 226M8R 22 TC A 1C 105M8R 1 TC A 1C 155M8R 1.5 TC A 1C 225M8R 2.2 TC A 1C 335M8R 3.310 2016 10 2016 10 2016 10 2016 0.8TC A 1C 475M8R 4.7 1.1TC A 1C 685M8R 6.8 1.6TC A 1C 106M8R 10 0.6 1.4 20+− 610 8 716 3225 0.5TC A 1E 105M8R 1 20+− 610 8 613 2620 0.5TC A 1D 155M8R 1.5 20+− 610 8 5.216 3225 0.6 TC A 1E 225M8R 2.2 20+− 610 8 5.213 2620 0.5TC A 1D 225M8R 2.2 20+− 610 8 4.813 2620 0.7TC A 1D 335M8R 3.3 20+− 610 8 3.913 2620 0.9TC A 1D 475M8R 4.7 20+− 610 8 713 2620 0.5TC A 1D 105M8R 1 20+− 610 8 616 3225 0.5TC A 1E 155M8R 1.5 20+− 812 10 3.416 3225 1.2TC A 1E 475M8R 4.7 20+− 610 8 722 4435 0.5TC A 1V 105M8R 1 20+− 610 8 4.816 3225 0.8TC A 1E 335M8R 3.3 20+− =Under development Part No. Rated voltage 85°C (V) Category voltage 125°C (V) Surge voltage 85°C (V) Cap. 120Hz (μF) Tolerance (%) Leakage current 25°C 1WV.60s (μA) Df 120Hz (%) −55°C 125°C25°C 85°C Impedance 100kHz (Ω)

7/7 www.rohm.com ○c 2011 ROHM Co., Ltd. All rights reserved. 2011.06 - Rev.F Data Sheet TC Series A Case  Packaging specifications Taping [A case] Case code A 1.9 3.5 0.25 1.9 Feeding direction 2.0±0.05 4.0±0.1 4.0 ±0.1 A B 8.0±0.2 3.5±0.05 1.75±0.1 Chip φ1.5 +0.1−0  Packaging style 2,000pcs Case code Packaging TapingA case Packaging style plastic taping φ180mm Reel Symbol R Basic ordering units Reel [A case] φ13 0.2 φ60 +10 0−1.5φ180 9.0 11.4 1.0 Label sticking position EIAJ ET−7200B compatible Pull direction +− +1.0

R1120Awww.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Notice ROHM Customer Support System http://ww w.rohm.com/contact/ Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. Notes