TC862X80X12

TC8 FRANCEJOINT | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 5

Technical content

|| SEAL DESIGN Tolerance for the outside diameter of the seal (ØD) Bore diameter ØD1 (mm) Apparent metal cage Rubber coating Coating with grooves Roundness tolerance Bore diameter ØD1 (mm) Apparent metal cage Rubber coating ØD1 ≤ 50.0 0.18 0.25 50.0 < ØD1 ≤ 80.0 0.25 0.35 80.0 < ØD1 ≤ 120.0 0.30 0.50 120.0 < ØD1 ≤ 180.0 0.40 0.65 180.0 < ØD1 ≤ 300.0 0.25% of the outside diameter 0.80 300.0 < ØD1 ≤ 500.0 0.25% of the outside diameter 1.00 Tolerance for the inside diameter of the seal (Ød) Free and without constraint, the inside diameter of the sealing lip is always smaller than the diameter of the shaft. The pre-tightening or interference denotes the difference between these two values. Depending on the shaft diameter, the diameter of the sealing lip is generally considered to be less, between 0.8 and 3.5 mm. Pumping leads Clockwise Anti-clockwise Bi-directional R L H0 Other types of pumping leads can be created according to your specifications. Please contact our experts. |DESCRIPTION The TC8 profile is a shaft seal composed of a single metal cage with a rubber coating, a primary sealing lip with an integrated spring and two additional anti-pollution lips. |ADVANTAGES Very good static sealing Very good thermal expansion compensation Greater roughness is allowed in the housing Reduced risk of corrosion Sealing for low and high viscosity fluids Modern primary sealing lip with low radial forces Protection against undesirable air contaminants |APPLICATIONS All types of rotative applications Machine tools Agriculture Construction Transmission Gear boxes Motors Pumps |MATERIALS Rubber ACM 70 - 75 Shore A EPDM 70 - 75 Shore A FKM 70 - 75 Shore A HNBR 70 - 75 Shore A NBR 70 - 75 Shore A Metal cage Steel - AISI 1010 Spring Steel - AISI 1070 - 1090 Stainless steel - AISI 316 STANDARD SHAFT SEALS TC8 ROTARY SEALS | STANDARD SHAFT SEALS | TC8 QUALITY & EXPERTISE FOR YOUR SEALING NEEDS

Maximum temperature depending on the materials ACM AEM EPDM FKM HNBR NBR VMQ Mineral oils Oils for motors +130°C +130°C – +170°C +130°C +100°C +150°C Oils for gearboxes +120°C +130°C – +150°C +110°C +80°C +130°C Oils for hypoid gears +120°C +130°C – +150°C +110°C +80°C – ATF oils +120°C +130°C – +170°C +130°C +100°C – Hydraulic oils +120°C +130°C – +150°C +130°C +90°C – Greases – +130°C – – +100°C +90°C – Fire-resistant fluids HFA group - Emulsion with more than 80% water – – – – +70°C +70°C +60°C HFB group - Opposite solution (water in oil) – – – – +70°C +70°C +60°C HFC group - Polymer aqueous solution – – +60°C – +70°C +70°C – HFD group - Water-free synthetic fluids – – – +150°C – – – Other fluids EL + L heating oil – – – – +100°C +90°C – Water for washing – – +130°C +100°C +100°C +90°C – Temperature range || TECHNICAL DATA Speed 20 40 60 80 100 120 140 160 180 200 500 1000 1500 2000 2500 3000 3500 4500 400050006000700090001500030000 800010000 Shaft diameter (mm) Shaft speed (r.p.m) Peripheral shaft speed (m/s) FKM / VMQ ACM / AEM / HNBR NBR PTFE The shaft seals with an additional protective lip are limited to a speed of 8 m/sec. Linear speed calculation: s (m/s) = [shaft Ø (mm) x speed (rpm) x π] 60,000 Pressure The standard shaft seals are generally used in unpressurised environments, or for pressures between 0.02 and 0.05 MPa maximum. Higher pressures are acceptable, following testing, for standard NBR or FKM shaft seals used on a shaft of less than 30 mm. 0,05 0,1 0,15 0,2 10 20 30 Shaft diameter (mm) Max. pressure (MPa) 1 m/s 1,5 m/s 2 m/s 2,5 m/s ROTARY SEALS | STANDARD SHAFT SEALS | TC8 www.francejoint.com

10° / 20° R2 max 20° / 30° Ø D1 H8 Ø d1 h11 Ø d3 R || SHAFT DESIGN Shaft hardness Rotation speed Hardness in HRC s ≤ 4.0 m/sec 45 HRC 4.0 < s ≤ 10.0 m/s 55 HRC s > 10.0 m/sec 60 HRC Surface roughness Ra * 0.2 to 0.8 µm Rz 1.0 to 4.0 µm Rmax ≤6.3 µm *Ra = 0.1 µm for demanding applications Shaft tolerance Shaft diameter Ød1 (mm) Tolerance h11 (mm) Ød1 ≤ 3.0 -0.060 / 0 10.0 < Ød1 ≤ 18.0 -0.110 / 0 18.0 < Ød1 ≤ 30.0 -0.130 / 0 30.0 < Ød1 ≤ 50.0 -0.160 / 0 50.0 < Ød1 ≤ 80.0 -0.190 / 0 80.0 < Ød1 ≤ 120.0 -0.220 / 0 120.0 < Ød1 ≤ 180.0 -0.250 / 0 180.0 < Ød1 ≤ 250.0 -0.290 / 0 250.0 < Ød1 ≤ 315.0 -0.320 / 0 315.0 < Ød1 ≤ 400.0 -0.360 / 0 400.0 < Ød1 ≤ 500.0 -0.400 / 0 Chamfer and radius Shaft diameter Ød1 (mm) Chamfer diameter Ød3 (mm) Radius R (mm) Ød1 ≤ 10.0 Ød1 - 1.50 2.00 10.0 < Ød1 ≤ 20.0 Ød1 - 2.00 2.00 20.0 < Ød1 ≤ 30.0 Ød1 - 2.50 3.00 30.0 < Ød1 ≤ 40.0 Ød1 - 3.00 3.00 40.0 < Ød1 ≤ 50.0 Ød1 - 3.50 4.00 50.0 < Ød1 ≤ 70.0 Ød1 - 4.00 4.00 70.0 < Ød1 ≤ 95.0 Ød1 - 4.50 5.00 95.0 < Ød1 ≤ 130.0 Ød1 - 5.50 6.00 130.0 < Ød1 ≤ 240.0 Ød1 - 7.00 8.00 240.0 < Ød1 ≤ 500.0 Ød1 - 11.00 12.00 Shaft run out Shaft speed (r.p.m) 0,1 0,2 0,3 0,4 PTFE NBR - HNBR - ACM - AEM - FKM VMQ 1000 2000 3000 4000 5000 6000 Shaft run-out (mm) Eccentricity Shaft diameter (mm) Eccentricity (mm) 25 50 100 200150 25075 125 175 225 275 0,1 0,2 0,3 0,4 ROTARY SEALS | STANDARD SHAFT SEALS | TC8 www.francejoint.com

Ra 1.6 to 6.3 µm Rz 10.0 to 25.0 µm Rmax ≤25.0 µm Housing tolerance Bore diameter ØD1 (mm) Tolerance H8 (mm) 10.0 < ØD1 ≤ 18.0 0 / +0.027 18.0 < ØD1 ≤ 30.0 0 / +0.033 30.0 < ØD1 ≤ 50.0 0 / +0.039 50.0 < ØD1 ≤ 80.0 0 / +0.046 80.0 < ØD1 ≤ 120.0 0 / +0.054 120.0 < ØD1 ≤ 180.0 0 / +0.063 180.0 < ØD1 ≤ 250.0 0 / +0.072 250.0 < ØD1 ≤ 315.0 0 / +0.081 315.0 < ØD1 ≤ 400.0 0 / +0.089 400.0 < ØD1 ≤ 500.0 0 / +0.097 500.0 < ØD1 ≤ 630.0 0 / +0.110 Housing radius and width Height H1 (mm) Width Radius R2 max (mm)L2min (H1 x 0.85) L1min (H1 x +0.3) 7.00 5.95 7.30 0.508.00 6.80 8.30 10.00 8.50 10.30 12.00 10.30 12.30 0.7015.00 12.75 15.30 20.00 17.00 20.30 || HOUSING DESIGN 10° / 20° R2 max 20° / 30° Ø D1 H8 Ø d1 h11 Ø d3 R ROTARY SEALS | STANDARD SHAFT SEALS | TC8 www.francejoint.com

|| DIMENSIONS Part number Shaft diameter Ød1 h11 Bore diameter ØD1 H8 Seal height TC8 19 x 32 x 8.5 19.00 32.00 8.50 TC8 20 x 30 x 7 20.00 30.00 7.00 TC8 20 x 31 x 6 20.00 31.00 6.00 TC8 24 x 45 x 9.5 24.00 45.00 9.50 TC8 25 x 35 x 7 25.00 35.00 7.00 TC8 25 x 40 x 7 25.00 40.00 7.00 TC8 25 x 40 x 9 25.00 40.00 9.00 TC8 25 x 47 x 8 25.00 47.00 8.00 TC8 25 x 47 x 9.5 25.00 47.00 9.50 TC8 25 x 52 x 10 25.00 52.00 10.00 TC8 27 x 72 x 9.5 27.00 72.00 9.50 TC8 27 x 80 x 10 27.00 80.00 10.00 TC8 28 x 42 x 7 28.00 42.00 7.00 TC8 28 x 47 x 10 28.00 47.00 10.00 TC8 30 x 44 x 8 30.00 44.00 8.00 TC8 30 x 45 x 7 30.00 45.00 7.00 TC8 32 x 48 x 8 32.00 48.00 8.00 TC8 32 x 50 x 6.5 32.00 50.00 6.50 TC8 32 x 52 x 10 32.00 52.00 10.00 TC8 35 x 62 x 8 35.00 62.00 8.00 TC8 35 x 65 x 8 35.00 65.00 8.00 TC8 36 x 52 x 10 36.00 52.00 10.00 Part number Shaft diameter Ød1 h11 Bore diameter ØD1 H8 Seal height TC8 37 x 60 x 10 37.00 60.00 10.00 TC8 40 x 55 x 8 40.00 55.00 8.00 TC8 40 x 58 x 11 40.00 58.00 11.00 TC8 40 x 62 x 8 40.00 62.00 8.00 TC8 40 x 70 x 8 40.00 70.00 8.00 TC8 42 x 62 x 8 42.00 62.00 8.00 TC8 42 x 66 x 10 42.00 66.00 10.00 TC8 45 x 68 x 12 45.00 68.00 12.00 TC8 46 x 62 x 8 46.00 62.00 8.00 TC8 47 x 58 x 7 47.00 58.00 7.00 TC8 47 x 69 x 10 47.00 69.00 10.00 TC8 48 x 65 x 9 48.00 65.00 9.00 TC8 48 x 68 x 12 48.00 68.00 12.00 TC8 48 x 72 x 7 48.00 72.00 7.00 TC8 50 x 62 x 7 50.00 62.00 7.00 TC8 50 x 72 x 12 50.00 72.00 12.00 TC8 56 x 77 x 9 56.00 77.00 9.00 TC8 62 x 80 x 12 62.00 80.00 12.00 TC8 75 x 110 x 13 75.00 110.00 13.00 TC8 80 x 100 x 10 80.00 100.00 10.00 TC8 90 x 125 x 15 90.00 125.00 15.00 ROTARY SEALS | STANDARD SHAFT SEALS | TC8 FRANCE JOINT SAS Zone Artisanale Le Mortier - B.P . 50009 - Cugand - 85613 Montaigu Cedex - France Ph. +33 (0)2 51 42 13 76 - Fax +33 (0)2 51 43 61 14 - Email: contact@francejoint.fr - Website: www.francejoint.com