TC4403 MICROCHIP | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 14
Technical content
Features
- Low Quiescent Current: 300 µA Max Capacitive Inputs With 300mV Hysteresis Both Inputs Must Be Driven to Drive Load Low Output Leakage High Peak Current Capability Fast Output Rise Time Outputs Individually Testable
Applications
Isolated Load Drivers P u l s e r s Safety Interlocks Device Selection Table Package Type General Description The TC4403 is a modified version of the TC4425 driver, intended to drive floating or isolated loads requiring high-current pulses. The load is intended to be con- nected between the outputs without other reference to supply or ground. Then, only when both logic inputs and the V DD input are energized, is power supplied to the load. This construction allows the implementation of a wide variety of redundant input controllers. The low OFF-state output leakage and independence of the two half-circuits permit a wide variety of testing schemes to be utilized to assure functionality. The high peak current capability, short internal delays, and fast output rise and fall times ensure that sufficient power will be available to the load when it is needed. The TTL and CMOS compatible inputs allow operation from a wide variety of input devices. The ability to swing the inputs negative without affecting device performance allows negative biases to be placed on the inputs for greater safety. In addition, the capacitive nature of the inputs allows the use of series resistors on the inputs for extra noise suppression. The TC4403 is built for outstanding ruggedness and reliability in harsh applications. Input voltage excur- sions above the supply voltage or below ground are clamped internally without damaging the device. The output stages are power MOSFETs with high-speed body diodes to prevent damage to the driver from inductive kickbacks. Part Number Package Temp. Range TC4403CPA 8-Pin PDIP 0°C to +70°C TC4403EPA 8-Pin PDIP -40°C to +85°C TC4403MJA 8-Pin CERDIP -55°C to +125°C TC4403 OUT (GND)IN (GND) GND IN (VDD) VDD OUT (VDD) NCNC 8-Pin PDIP/CERDIP 1.5A High-Speed, Floating Load Driver
DS21417B-page 2 2002 Microchip Technology Inc. Functional Block Diagram Typical Application TC4403 300mV Input Hysteresis Effective Input C = 20pF (Each Input) GND IN (VDD) IN (GND) 4 OUT (VDD) OUT (GND) VDD Power 1 MΩ RLOADTC4403 -15V 1 MΩ +15V RT RT TC4422 Fire Arm
2002 Microchip Technology Inc. DS21417B-page 3 TC4403
1.0 ELECTRICAL
Absolute Maximum Ratings* Package Thermal Resistance Operating Temperature Range *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. TC4403 ELECTRICAL SPECIFICATIONS Electrical Characteristics: TA = +25°C, with 4.5V ≤ VDD ≤ 18V, unless otherwise noted. Symbol Parameter Min Typ Max Units Test Conditions Input VIH Logic 1, High Input Voltage 2.4 —— V VIL Logic 0, Low Input Voltage —— 0.8 V IIN Input Current -1000 ±10 ±1000 nA -5V ≤ VIN ≤ VDD Output VOH High Output Voltage V DD – 0.025 —— V VOL Low Output Voltage —— 0.025 V ROS Sourcing Output Resistance — 2.8 5 Ω IOUT = 10mA, VDD = 18V ROG Grounding Output Resistance — 3.5 5 Ω IOUT = -10mA, VDD = 18V IPK Peak Output Current — 1.5 — A Switching Time (Note 1) tR Rise Time — 23 35 nsec Figure 3-1, C L = 1800pF tF Fall Time — 25 35 nsec Figure 3-1, C L = 1800pF tD1 Delay Time — 33 75 nsec Figure 3-1, C L = 1800pF tD2 Delay Time — 38 75 nsec Figure 3-1, C L = 1800pF Power Supply I S Power Supply Current — 1.5 0.15 2.5 0.25 mA V IN = 3V (Both Inputs) VIN = 0V (Both Inputs) Note 1: Switching times ensured by design.
DS21417B-page 4 2002 Microchip Technology Inc. TC4403 ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: Over operating temperature range with 4.5V ≤ VDD ≤ 18V, unless otherwise noted. Symbol Parameter Min Typ Max Units Test Conditions Input VIH Logic 1, High Input Voltage 2.4 —— V VIL Logic 0, Low Input Voltage —— 0.8 V IIN Input Current -10,000 ±10 ±10,000 nA -5V ≤ VIN ≤ VDD Output VOH High Output Voltage V DD – 0.025 —— V VOL Low Output Voltage —— 0.025 V ROS Sourcing Output Resistance — 3.7 8 Ω VIN = 2.4V, IOUT = 10mA, VDD = 18V ROG Grounding Output Resistance — 4.3 8 Ω VIN = 2.4V, IOUT = -10mA, VDD = 18V Switching Time (Note 1) tR Rise Time — 28 60 nsec Figure 3-1, C L = 1800pF tF Fall Time — 32 60 nsec Figure 3-1, C L = 1800pF tD1 Delay Time — 32 100 nsec Figure 3-1, C L = 1800pF tD2 Delay Time — 38 100 nsec Figure 3-1, C L = 1800pF Power Supply IS Power Supply Current — 0.2 3.5 0.3 mA V IN = 3V (Both Inputs) VIN = 0V (Both Inputs) Note 1: Switching times ensured by design.
2002 Microchip Technology Inc. DS21417B-page 5 TC4403
2.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Pin No. (8-Pin PDIP, CERDIP) Symbol Description 1 NC No connection. 2I N ( V DD) Control input V DD, TTL/CMOS compatible logic input signal, controls OUT (V DD). 3 GND Ground. 4 IN (GND) Control Input GND, TTL/CMOS compatible logic input signal, controls OUT (GND). 5 OUT (GND) Output GND, CMOS Pull Down Output. DD Supply Input, 4.5V to 18V. 7O U T ( V DD) Output V DD, CMOS pull-up output. 8 NC No connection.
DS21417B-page 6 2002 Microchip Technology Inc.
3.0 APPLICATIONS INFORMATION
FIGURE 3-1: SWITCHING TIME TEST CIRCUITS Input VDD Input GND 0.1µF MLC 1µF WIMA MKS-2 10kΩ TC4403 0.1µF MLC 10KΩ TC4403 +5V 10% 90% 10% 16V 10% 90% 10% 1µF WIMA MKS-2 Input VDD VDD = 16V Input Output tD1 tF CL = 1800pF Output tR +5V 16V Input Output tD1 CL = 1800pF Output VDD = 16V Input GND
2002 Microchip Technology Inc. DS21417B-page 7 TC4403
4.0 TYPICAL CHARACTERISTICS
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. tRISE (nsec) 4 6 8 10 12 14 16 18 Rise Time vs. Supply Voltage 100 p1000pF pp4700pF 3300pF 470pF p1500pF pp2200pF TA °C VDD (V) Rise Time vs. Capacitive Load 100 1000 10,000 CLOAD (pF) 10V 15V 100 TA = +25°C tRISE (nsec)TIME (nsec) Rise and Fall Times vs. Temperature -55 -35 5 25 45 65 85 105 125-15 TEMPERATURE (°C) tFALL tRISE tFALL tRISE C = 2200pF V = 18V tFALL (nsec) 4 6 8 10 12 14 16 18 Fall Time vs. Supply Voltage 100 p1000pF 1500pFp pp4700pF 3300pF pp2200pF 44470pF VDD (V) TA = +25°C Fall Time vs. Capacitive Load 100 1000 10,000 10V 15V 100 TA = +25°C tFALL (nsec) CLOAD (pF) Propagation Delay vs. Input Amplitude 100 DELAY TIME (nsec) INPUT (V) 0 1 2 3 4 5 6 7 8 9 10 11 12 tD1 tD2 C = 2200pF VDD
DS21417B-page 8 2002 Microchip Technology Inc. TYPICAL CHARACTERISTICS (CONTINUED) Delay Time vs. Supply Voltage 4 6 8 10 12 14 16 18 DELAY TIME (nsec) VDD (V) C T °C tD1 tD2 0.1 0.01 4 6 8 10 12 14 16 18 IQUIESCENT (mA) Quiescent Current vs. Voltage BOTH INPUTS = 1 BOTH INPUTS = 0 VDD (V) TA = +25°CC 5.7 5.1 4.5 3.9 3.3 2.7 2.1 1.5 75 150 225 300
75 HOURS
2.768V CLOSED CIRCUIT VOLTAGE HOURS OF SERVICE 2.727V Typical Discharge Characteristics Delay Time vs. Temperature DELAY TIME (ns) -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (°C) CCLOAD = 2200pF tD1 tD2 -55 -35 -15 5 25 45 65 85 105 125 Quiescent Current vs. Temperature 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 INPUTS = 1 INPUTS = 0 TEMPERATURE (°C) IQUIESCENT (mA) 200 400 600 800 1000 1200 1400 1600 0 10 20 30 40 50 60 70 80 90 100 110 120 AMBIENT TEMPERATURE (°C) MAX. POWER (mW)
8 Pin DIP
88 Pin CERDIP
2002 Microchip Technology Inc. DS21417B-page 9 TC4403
5.0 PACKAGING INFORMATION
5.1 Package Marking Information
Package marking data not available at this time.
5.2 Package Dimensions
3° MIN. PIN 1 .260 (6.60) .240 (6.10) .045 (1.14) .030 (0.76) .070 (1.78) .040 (1.02) .400 (10.16) .348 (8.84) .200 (5.08) .140 (3.56) .150 (3.81) .115 (2.92) .110 (2.79) .090 (2.29) .022 (0.56) .015 (0.38) .040 (1.02) .008 (0.20) .310 (7.87) .290 (7.37) .400 (10.16) .310 (7.87) 8-Pin Plastic DIP Dimensions: inches (mm) .400 (10.16) .370 (9.40) .300 (7.62) .230 (5.84) .065 (1.65) .045 (1.14) PIN 1 .200 (5.08) .160 (4.06) .200 (5.08) .125 (3.18) .110 (2.79) .090 (2.29) .020 (0.51) .016 (0.41) .040 (1.02) .020 (0.51) .320 (8.13) .290 (7.37) .150 (3.81) MIN. 3° MIN. 8-Pin CERDIP (Narrow) .015 (0.38) .008 (0.20) .400 (10.16) .320 (8.13) Dimensions: inches (mm)
DS21417B-page 10 2002 Microchip Technology Inc. NOTES:
2002 Microchip Technology Inc. DS21417B-page11 TC4403 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recom- mended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. Your local Microchip sales office 2. The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 3. The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
DS21417B-page12 2002 Microchip Technology Inc. NOTES:
2002 Microchip Technology Inc. DS21417B-page 13 TC4403 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical com- ponents in life support systems is not authorized except with express written approval by Microchip. No licenses are con- veyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, FilterLab, K EELOQ, microID, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Tech- nology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified.
DS21417B-page 14 2002 Microchip Technology Inc. M AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Rocky Mountain 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 Atlanta
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Boston
2 Lan Drive, Suite 120
Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Chicago
333 Pierce Road, Suite 180
Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas
4570 Westgrove Drive, Suite 160
Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles
18201 Von Karman, Suite 1090
Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 New York
150 Motor Parkway, Suite 202
Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 San Jose Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Toronto
6285 Northam Drive, Suite 108
Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Australia Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 China - Chengdu Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-6766200 Fax: 86-28-6766599 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 China - Shanghai Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 China - Shenzhen Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086 Hong Kong Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India Microchip Technology Inc. India Liaison Office Divyasree Chambers
1 Floor, Wing A (A3/A4)
No. 11, O’Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Japan Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd.
200 Middle Road
#07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Denmark Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 France Microchip Technology SARL Parc d’Activite du Moulin de Massy
43 Rue du Saule Trapu
91300 Massy, France
D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Italy Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1
20041 Agrate Brianza
Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 United Kingdom Arizona Microchip Technology Ltd.
505 Eskdale Road
Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 03/01/02 /G39/G7/G22/G31/G30/G33/G30/G36/G5/G39 WORLDWIDE SALES AND SERVICE