TBYV26C TSC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
/cuspopen Low forward voltage drop high current capability /cuspopen Low leakage current /cuspopen Ultrafast recovery time for high efficiency /cuspopen High surge current capability Mechanical Data /cuspopen Cases: Molded plastic DO-41 /cuspopen Epoxy: UL 94V-O rate flame retardant /cuspopen Lead: Axial leads, solderable per MIL-STD-202, Method 208 guaranteed /cuspopen Polarity: Color band denotes cathode end /cuspopen High temperature soldering guaranteed: 260oC/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs., (2.3kg) tension /cuspopen Weight: 0.34gram DO-41 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 ℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol TBYV26C Units Maximum Recurrent Peak Reverse Voltage VRRM 600 V Maximum RMS Voltage VRMS 420 V Maximum DC Blocking Voltage VDC 600 V Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length @T A = 55℃ (See Fig. 1) I(AV) 1.0 A Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) IFSM 30 A Maximum Instantaneous Forward Voltage @ 1 . 0 A T j = 2 5 ℃ T j = 1 7 5 ℃ VF 2.5 1.3 V Maximum DC Reverse Current @ T A=25℃ at Rated DC Blocking Voltage @ TA=165℃ IR 5.0 150 uA uA Maximum Reverse Recovery Time ( Note 1 ) Trr 30 nS Typical Junction Capacitance ( Note 2 ) Cj 45 pF Maximum Reverse recovery Current Slope dIr/dt @ IF=1A, VR=30V, dIf/dt = 1A / uS dv/dt 7 A/uS Typical Thermal Resistance (Note 3) RθJA 60 ℃/W Operating Temperature Range TJ -65 to +175 ℃ Storage Temperature Range TSTG -65 to +175 ℃ Notes: 1. Reverse Recovery Test Conditions: I F=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Thermal Resistance from Junction to Ambi ent at 0.375”(9.5mm) Lead Length, Mount on 0.2” x 0.2” (5mm x 5mm) Cu pads.
- 365 - 0.001 20 40 60 80 100 0.1 0.01 100 Tj=25 C0 Tj=165 C0 FIG.2- MAXIMUM AVERAGE FORWARD CURRENT DERATING FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM AVERAGE FOR WARD CURRENT . (A) 25 50 75 100 125 150 175 1.0 2.0 AMBIENT TEMPERATURE. ( C) o 50/c87 NONINDUCTIVE /c49/c87 NON INDUCTIVE OSCILLOSCOPE (NOTE 1) PULSE GENERATOR (NOTE 2) DUT (+) 50Vdc (approx) (-) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms (-) (+) 10/c87 NONINDUCTIVE -1.0A -0.25A +0.5A trr 1cm SET TIME BASE FOR 5/ 10ns/ cm Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length RATINGS AND CHARACTERISTIC CURVES (TBYV26C) FIG.5- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FOR WARD SURGE CURRENT . (A) 1 2 5 10 20 100 50 NUMBER OF CYCLES AT 60Hz 8.3ms Single Half Sine Wave JEDEC Method FIG.3- TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT .( A ) PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.4- TYPICAL FORWARD CHARACTERISTICS INSTANTANEOUS FOR WARD CURRENT . (A) 0.01 0.1 1.0 FORWARD VOLTAGE. (V) FIG.6- TYPICAL JUNCTION CAPACITANCE JUNCTION CAP ACITANCE.(pF) 0.1 0.5 1 5 2 10 20 50 100 200 500 1000 REVERSE VOLTAGE. (V) Tj=25 C0 Tj=165 C0