TA100W-11 MORNSUN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

The copyright and authority for the interpretation of the products are reserved by MORNSUN TAxxxW-xx 2013.04.10-A/2 Page 1 of 4 12.5mm analog signal isolators / Transducers power supply —— TAxxxW-xx Series PART NUMBER SYSTEM TxxxW-xxA Slim case Analogsignal Serial number Transducer type Channel configuration Signal style

FEATURES

  • Three-port isolation (input, output and power supply)
  • 12.5mm slim case
  • High accuracy (0.1% F.S.)
  • High linearity (0.1% F.S.)
  • Low Output Ripple & Noise (≤60MVP-P )
  • Low temperature drift(35PPM/°C)
  • Low-power dissipation
  • Excellent EMC performance
  • High reliability(MTBF>500,000 hours) GENERAL DESCRIPTION The current or voltage signal from application field is picked up by this product and transmitted to the control cabinet. One independent power supply is required. Moreover, within the interface of rail power supply, input and output are mutually isolated. A green LED indicates that the device is working. Field devices connected with this product:2-wire or 3-wire isolation transducer (Distribution), industrial standard current source (not to be used in intrinsically safe area). SELECTION GUIDE TA x xx W- x x Description 1 1 input 1 output 2 2 input 2 output Channels 6 1 input 2 output

00 Current signal input, Current source or voltage source output

02 Current signal input,2-wire current source output

05 (Distribution)2-wire current input, current source or voltage source output 40 voltage signal input, current source or voltage source output Serial Number 42 voltage signal input, 2-wire current source output Package mark Slim case 1 4~20mA 2 0~20mA 3 2~10V 4 1~5V 5 0~10V Input signal 6 0~5V 1 4~20mA 2 0~20mA 3 2~10V 4 1~5V 5 0~10V Output signal 6 0~5V Note: Customers need to choose the type of the input signal and output signal. We could also offer customer design for special input and output.

ELECTRICAL CHARACTERISTICS

Input voltage 18~30VDC（Typical 24VDC） 1 input 1 output 1 input 2 output/2 input 2 output ≤1.2W(TA100W) ≤2W(TA600W/TA200W) Power Dissipation ≤1.5W(TA105W) ≤2W(TA605W/TA205W) Power Supply Power Protection Reverse connection protection

The copyright and authority for the interpretation of the products are reserved by MORNSUN TAxxxW-xx 2013.04.10-A/2 Page 2 of 4 No-load Voltage 24V±10% Distribution (Isolators with isolated power output) Full-load Voltage ≥20V Input Signal See selection guide ≤2V（Current input @20mA） Field Area Input Impedance ≥100KΩ（Voltage input） Output Signal See selection guide Ripple & Noise ≤60mVp-p ≤500Ω（@maximum output current) Control Area Load ≥1000Ω（@maximum output voltage） TRANSMISSION CHARACTERISTICS Zero Offset 0.1%F.S. Accuracy 0.1%F.S. Gain Error 0.1%F.S. Temperature drift coefficient 0.0035%F.S./℃（-25℃~+71 Operating temperature range℃ ） ISOLATION CHARACTERISTICS Electrical Isolation Three-port isolation (input, output and power supply) 2.0KVAC,3.0KVDC between application field and control cabinet 2.0KVAC,3.0KVDC between signal input or output and power supply Isolation Voltage 2.0KVAC,3.0KVDC between channels ( multi-channel products ) Test conditions: testing for 1minute, humidity < 70%, leakage current < 1mA EMC CHARACTERISTICS RE CISPR22/EN55022 CLASS A EMI CE CISPR22/EN55022 CLASS A ESD IEC/EN61000-4-2 Contact ±4KV / Air ±8KV perf. Criteria B IEC/EN61000-4-4 DC Power Port ±2KV perf. Criteria B EFT IEC/EN61000-4-4 I/O Signal Port ±1KV perf. Criteria B IEC/EN61000-4-5 DC Power Port ±1KV /±2KV perf. Criteria B Surge IEC/EN61000-4-5 I/O Signal Port ±1KV(Line to GND) perf. Criteria B OTHER CHARACTERISTICS Operating temperature range: -25°C ~ +71°C Ambient temperature Transport and storage temperature: -40°C ~ +85°C Safety Class IP20(IEC60529 / EN60529) Weight 1 input 1 output: about 100g;2 input 2 output & 1 input 2 output: about128g CONNECTION 1. Connection used dismountable terminals; 2. Cross section area of wiring: 0.5mm ~2.5 mm 3. The length of bare wire is about 8mm, locked up by the M3 bolt. Application in industry In the field application, isolator should not be installed In intrinsically safe area. Selection guidelines for Isolator or Isolator with isolation power output 1. Take care of output independence of isolator or isolator with isolation power output and loop resistance to make sure the its output voltage meets the minimum operation voltage requirement of field device. 2. Select suitable isolator which matches the field device according to its power polarity, signal type and transmission mode. Operation notes 1. Please read the user manual carefully before using. If any question please contact our technical support department. 2. Please do not use this product in hazardous area. 3. The power supply of this product should be 24VDC power source. It is forbidden to use 220VAC power supply. 4. To avoid invalid explosion protection function, or any failure, users disassemble this product is forbidden.

The copyright and authority for the interpretation of the products are reserved by MORNSUN TAxxxW-xx 2013.04.10-A/2 Page 3 of 4 APPLICATION CIRCUIT DIAGRAM & PIN DESCRIPTION Bottom power supply port

8 Inside

Note: When use bottom power supply, anyone group or both is OK. PIN TAx00W（Isolators）

1 Si2- Signal 2 input-

2 Si2+ Signal 2 input+

5 Si1- Signal 1 input-

6 Si1+ Signal 1 input+

7 So1- Signal 1 output-

8 So1+ Signal 1 output+

9 So2- Signal 2 output-

10 So2+ Signal 2 output+

11 Power- Power Input-

12 Power+ Power Input+

(Isolator With Isolated Power Output Circuit Diagram) TAx05W (Isolator Circuit Diagram)

1 Signal 2 isolated input- Signal 2 input +

2 Signal 2 isolated input+ /

5 Signal 1 isolated input- Signal 1 input +

6 Signal 1 isolated input+ /

7 Signal 1 output- Signal 1 output-

8 Signal 1 output+ Signal 1 output+

9 Signal 2 output- Signal 2 output-

10 Signal 2 output+ Signal 2 output+

11 Power input- Power input-

12 Power input+ Power input+

+ 12 - 11 Channel 2 4～20mA 4～20mA DCS/PLC

2 INPUT2 OUTPUT

+ 8 - 7 + 10 - 9 RL RL TAx00W Series signal input Channel 1 signal input Vo1 Vo2 RL RL Channel 2 Channel 1 24VDC 24VDC + 12 - 11 4～20mA 4～20mA DCS/PLC Vo1 Vo2 + 8 - 7 + 10 - 9 + 6 S 5 - 4 + 2 S 1 - 3 RL RL RL RL Channel 22-wire circuit3-wire circuit 2-wire circuit3-wire circuit

The copyright and authority for the interpretation of the products are reserved by MORNSUN TAxxxW-xx 2013.04.10-A/2 Page 4 of 4 INSTALLATION & DISASSEMBLY Installation DIN35mm standard rail installation: 1. Insert the top of the instrument card in the rail; 2. Push the bottom of the instrument into the rail. Disassembly 1. Insert a screwdriver between the bottom of the card lock and the rail; 2. Pull up the screwdriver and press the card lock downwards; 3. Pull the instrument out of the rail. PACKAGING DIMENSION & PACKAGING DIAGRAM Note: 1. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. In this datasheet, all the test setup and methods are based on our corporate standards. 3. All characteristics are meant for listed model, non-standard models may perform differently, you can contact MORNSUN FAE for more details. 4. Contact us for your specific requirement. 5. Specifications are subject to change without prior notice. MORNSUN Science & Technology Co.,Ltd. Tel: 86-20-38601850 Fax:86-20-38601272 E-mail: info@mornsun.cn Http://www.mornsun-power.com