T7808CT

MCT7800 MOTOROLA | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 12

Technical content

Order this document by MCT7800/D /C0077/C0067/C0084/C0055/C0056/C0048/C0048 /C0083/C0101/C0114/C0105/C0101/C0115 THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS Pin 1. Input 2. Ground 3. Output STANDARD APPLICATION A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage. XX, these two digits of the type number indicate nominal voltage. Cin is required if regulator is located an appreciable distance from power supply filter. Some CO is recommended for stability; it does improve transient response. Values less than 0.1 µF could cause instability. MCT78XXInput C in* 0.33 µF C O ** Output T SUFFIX PLASTIC PACKAGE CASE 221A Heatsink surface connected to Pin 2. D2T SUFFIX PLASTIC PACKAGE CASE 936 (D2PAK) 1 2 Heatsink surface (shown as terminal 4 in case outline drawing) is connected to Pin 2. MCT7800MOTOROLA /C0084/C0104/C0114/C0101/C0101/C0262/C0084/C0101/C0114/C0109/C0105/C0110/C0097/C0108 /C0080/C0111/C0115/C0105/C0116/C0105/C0118/C0101 /C0086/C0111/C0108/C0116/C0097/C0103/C0101 /C0082/C0101/C0103/C0117/C0108/C0097/C0116/C0111/C0114/C0115 These voltage regulators are monolithic integrated circuits designed as fixed-voltage regulators for a wide variety of applications including local, on-card regulation. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation. With adequate heatsinking they can deliver output currents in excess of 1.0 A. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltages and currents.

• Output Current in Excess of 1.0 A
• No External Components Required
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting
• Output Transistor Safe-Area Compensation
• Output Voltage Offered with a 4% Tolerance
• Available in Surface Mount D2PAK and Standard 3-Lead Transistor Packages This MCT-prefixed device is intended to be a possible replacement for the similar device with the MC-prefix. Because the MCT device originates from different source material, there may be subtle differences in typical parameter values or characteristic curves. Due to the diversity of potential applications, Motorola can not assure identical performance in all circuits. Motorola recommends that the customer qualify the MCT-prefixed device in each potential application. DEVICE TYPE/NOMINAL OUTPUT VOLTAGE MCT7805 MCT7806 MCT7808 MCT7809 5.0 V 6.0 V 8.0 V 9.0 V MCT7812 MCT7815 MCT7818 MCT7824 12 V 15 V 18 V 24 V

ORDERING INFORMATION

TJ = – 40° to +125°C Surface Mount MCT78XXBT TJ = – 40° to +125°C Insertion Mount MCT78XXCD2T TJ = 0° to +125°C Surface Mount MCT78XXCT TJ = 0° to +125°C Insertion Mount XX indicates nominal voltage.  Motorola, Inc. 1994 Rev 3

MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.) Rating Symbol Value Unit Input Voltage VI 35 Vdc Power Dissipation Case 221A TA = +25°C PD Internally Limited W Thermal Resistance, Junction-to-Ambient θJA 65 °C/W Thermal Resistance, Junction-to-Case θJC 5.0 °C/W Case 936 (D2PAK) TA = +25°C PD Internally Limited W Thermal Resistance, Junction-to-Ambient θJA 70 °C/W Thermal Resistance, Junction-to-Case θJC 5.0 °C/W Storage Junction T emperature Range Tstg – 65 to +150 °C Operating Junction T emperature TJ +150 °C Representative Schematic Diagram 100 500 3.3 k 2.7 k 500 1.4 k 100 100 10 k Input Output Gnd 240 200 0.3 6.0 k 2.0 k 30 pF28 k 6.0 k 1.0 k 5.0 k 0.25 k 5.0 k This device contains 19 active transistors.

ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7805B MCT7805C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

7.0 Vdc ≤ Vin ≤ 20 Vdc

8.0 Vdc ≤ Vin ≤ 20 Vdc

4.75 5.0 5.25 4.75 5.0 5.25 Vdc Line Regulation, TJ = +25°C (Note 2)

7.0 Vdc ≤ Vin ≤ 25 Vdc

8.0 Vdc ≤ Vin ≤ 12 Vdc

7.0 2.0 100 7.0 2.0 100 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ Vin ≤ 1.5 A 250 mA ≤ Vin ≤ 750 mA Reg load 2.0 1.5 100 2.0 1.5 100 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change

8.0 Vdc ≤ Vin ≤ 25 Vdc

5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.3 0.5 1.3 0.5 mA Ripple Rejection

8.0 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz

— 65 — — 65 — dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C)

10 Hz ≤ f ≤ 100 kHz

— 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 1.3 — — 1.3 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — 0.5 — — 0.5 — mV/°C ELECTRICAL CHARACTERISTICS (Vin = 11 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7806B MCT7806C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

8.0 Vdc ≤ Vin ≤ 21 Vdc

9.0 Vdc ≤ Vin ≤ 21 Vdc

5.7 6.0 6.3 5.7 6.0 6.3 Vdc Line Regulation, TJ = +25°C (Note 2)

9.0 Vdc ≤ Vin ≤ 13 Vdc

7.0 2.0 120 7.0 2.0 120 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ Vin ≤ 1.5 A 250 mA ≤ Vin ≤ 750 mA Reg load 2.0 1.5 120 2.0 1.5 120 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change

9.0 Vdc ≤ Vin ≤ 25 Vdc

5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.3 0.5 1.3 0.5 mA Ripple Rejection

9.0 Vdc ≤ Vin ≤ 19 Vdc, f = 120 Hz

— 65 — — 65 — dB NOTES: 1. Tlow = 0 °C for MCT78XXC T high = +125 °C for MCT78XXB, C.When the junction temperature exceeds +125°C, internal current limiting = – 40 °C for MCT78XXB will reduce the output current to less than 1.0 A at a VI–VO of 15 V or greater. The MC7800 die will supply more current under the sam e conditions. 2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

ELECTRICAL CHARACTERISTICS (continued) (Vin = 11 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7806B MCT7806C Characteristics Symbol Min Typ Max Min Typ Max Unit Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C) — 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 1.3 — — 1.3 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — –0.8 — — –0.8 — mV/°C ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7808B MCT7808C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

10.5 Vdc ≤ Vin ≤ 23 Vdc

11.5 Vdc ≤ Vin ≤ 23 Vdc

7.6 8.0 8.4 7.6 8.0 8.4 Vdc Line Regulation, TJ = +25°C (Note 2)

10.5 Vdc ≤ Vin ≤ 25 Vdc

11 Vdc ≤ Vin ≤ 17 Vdc

7.0 2.0 160 7.0 2.0 160 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Reg load 2.0 1.5 160 2.0 1.5 160 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change

11.5 Vdc ≤ Vin ≤ 25 Vdc

5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.0 0.5 1.0 0.5 mA Ripple Rejection 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz RR — 63 — — 63 — dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C) — 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 18 — — 18 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — –0.8 — — –0.8 — mV/°C NOTES: 1. Tlow = 0 °C for MCT78XXC T high = +125 °C for MCT78XXB, C.When the junction temperature exceeds +125°C, internal current limiting = – 40 °C for MCT78XXB will reduce the output current to less than 1.0 A at a VI–VO of 15 V or greater. The MC7800 die will supply more current under the sam e conditions. 2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7809B MCT7809C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

11.5 Vdc ≤ Vin ≤ 24 Vdc

12.5 Vdc ≤ Vin ≤ 24 Vdc

8.55 9.0 9.45 8.55 9.0 9.45 Vdc Line Regulation, TJ = +25°C (Note 2)

11.5 Vdc ≤ Vin ≤ 26 Vdc

11.5 Vdc ≤ Vin ≤ 17 Vdc

8.0 4.0 8.0 4.0 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Reg load 3.0 2.0 3.0 2.0 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change

12.5 Vdc ≤ Vin ≤ 26 Vdc

5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.0 0.5 1.0 0.5 mA Ripple Rejection 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz RR — 62 — — 62 — dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C) — 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 18 — — 18 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — –1.0 — — –1.0 — mV/°C ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7812B MCT7812C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = +25°C) VO 11.5 12 12.5 11.5 12 12.5 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

14.5 Vdc ≤ Vin ≤ 27 Vdc

15.5 Vdc ≤ Vin ≤ 27 Vdc

11.4 12.6 11.4 12.6 Vdc Line Regulation, TJ = +25°C (Note 2)

14.5 Vdc ≤ Vin ≤ 30 Vdc

16 Vdc ≤ Vin ≤ 22 Vdc

5.0 240 120 5.0 240 120 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Reg load 3.0 2.0 240 120 3.0 2.0 240 120 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change

15 Vdc ≤ Vin ≤ 30 Vdc

5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.0 0.5 1.0 0.5 mA NOTES: 1. Tlow = 0 °C for MCT78XXC T high = +125 °C for MCT78XXB, C.When the junction temperature exceeds +125°C, internal current limiting = – 40 °C for MCT78XXB will reduce the output current to less than 1.0 A at a VI–VO of 15 V or greater. The MC7800 die will supply more current under the sam e conditions. 2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

ELECTRICAL CHARACTERISTICS (continued) (Vin = 19 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7812B MCT7812C Characteristics Symbol Min Typ Max Min Typ Max Unit Ripple Rejection

15 Vdc ≤ Vin ≤ 25 Vdc, f = 120 Hz

— 62 — — 62 — dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C) — 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 18 — — 18 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — –1.0 — — –1.0 — mV/°C ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7815B MCT7815C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = +25°C) VO 14.4 15 15.6 14.4 15 15.6 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

17.5 Vdc ≤ Vin ≤ 30 Vdc

18.5 Vdc ≤ Vin ≤ 30 Vdc

14.25 15.75 14.25 15.75 Vdc Line Regulation, TJ = +25°C (Note 2)

20 Vdc ≤ Vin ≤ 26 Vdc

5.0 300 150 5.0 300 150 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ Vin ≤ 1.5 A 250 mA ≤ Vin ≤ 750 mA Reg load 3.0 2.0 300 150 3.0 2.0 300 150 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change 5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.0 0.5 1.0 0.5 mA Ripple Rejection 18.5 Vdc ≤ Vin ≤ 28.5 Vdc, f = 120 Hz RR — 60 — — 60 — dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C) — 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 19 — — 19 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — –1.0 — — –1.0 — mV/°C NOTES: 1. Tlow = 0 °C for MCT78XXC T high = +125 °C for MCT78XXB, C.When the junction temperature exceeds +125°C, internal current limiting = – 40 °C for MCT78XXB will reduce the output current to less than 1.0 A at a VI–VO of 15 V or greater. The MC7800 die will supply more current under the sam e conditions. 2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7818B MCT7818C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = +25°C) VO 17.3 18 18.7 17.3 18 18.7 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

21 Vdc ≤ Vin ≤ 33 Vdc

22 Vdc ≤ Vin ≤ 33 Vdc

17.1 18.9 17.1 18.9 Vdc Line Regulation, TJ = +25°C (Note 2)

24 Vdc ≤ Vin ≤ 30 Vdc

5.0 360 180 5.0 360 180 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ Vin ≤ 1.5 A 250 mA ≤ Vin ≤ 750 mA Reg load 4.0 3.0 360 180 4.0 3.0 360 180 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change 5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.0 0.5 1.0 0.5 mA Ripple Rejection

22 Vdc ≤ Vin ≤ 32 Vdc, f = 120 Hz

— 59 — — 59 — dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) ViI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C) — 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 19 — — 19 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — –1.0 — — –1.0 — mV/°C ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 500 mA, TJ = Tlow to Thigh [Note 1], unless otherwise noted.) MCT7824B MCT7824C Characteristics Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = +25°C) VO 23 24 25 23 24 25 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PO ≤15 W)

27 Vdc ≤ Vin ≤ 38 Vdc

28 Vdc ≤ Vin ≤ 38 Vdc

22.8 25.2 22.8 25.2 Vdc Line Regulation, TJ = +25°C (Note 2)

30 Vdc ≤ Vin ≤ 36 Vdc

6.0 480 240 6.0 480 240 mV Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Reg load 5.0 4.0 480 240 5.0 4.0 480 240 mV Quiescent Current (TJ = +25°C) IB — 5.5 8.0 — 5.5 8.0 mA Quiescent Current Change 5.0 mA ≤ IO ≤ 1.0 A ΔIB 1.0 0.5 1.0 0.5 mA Ripple Rejection

28 Vdc ≤ Vin ≤ 38 Vdc, f = 120 Hz

— 56 — — 56 — dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI – VO — 2.0 — — 2.0 — Vdc Output Noise Voltage (TA = +25°C) — 10 — — 10 — µV/VO Output Resistance f = 1.0 kHz rO — 20 — — 20 — m Ω Short Circuit Current Limit (TA = +25°C) Vin = 35 Vdc ISC — 0.2 — — 0.2 — A Peak Output Current (TJ = +25°C) Imax — 2.2 — — 2.2 — A Average Temperature Coefficient of Output VoltageTCV O — –1.5 — — –1.5 — mV/°C NOTES: 1. Tlow = 0 °C for MCT78XXC T high = +125 °C for MCT78XXB, C.When the junction temperature exceeds +125°C, internal current limiting = – 40 °C for MCT78XXB will reduce the output current to less than 1.0 A at a VI–VO of 15 V or greater. The MC7800 die will supply more current under the sam e conditions. 2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

A B C D F G H J K L N Q R S T U V Z 14.48 9.66 4.07 0.64 3.61 2.42 2.80 0.46 12.70 1.15 4.83 2.54 2.04 1.15 5.97 0.00 1.15 15.75 10.28 4.82 0.88 3.73 2.66 3.93 0.64 14.27 1.52 5.33 3.04 2.79 1.39 6.47 1.27 2.04 0.570 0.380 0.160 0.025 0.142 0.095 0.110 0.018 0.500 0.045 0.190 0.100 0.080 0.045 0.235 0.000 0.045 0.620 0.405 0.190 0.035 0.147 0.105 0.155 0.025 0.562 0.060 0.210 0.120 0.110 0.055 0.255 0.050 0.080 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIM Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. -T- SEATING PLANE C ST U J R FB Q H Z L V G N D K A 1 2 3 D2T SUFFIX PLASTIC PACKAGE CASE 936-03 (D2PAK)

5 REF5 REF

A 1 2 3 K F B J S H 0.010 (0.254) TM D G C E -T- M L P N R V U TERMINAL 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. DIM A MIN MAX MIN MAX MILLIMETERS 0.386 0.403 9.804 10.236 INCHES B 0.356 0.368 9.042 9.347 C 0.170 0.180 4.318 4.572 D 0.026 0.036 0.660 0.914 E 0.045 0.055 1.143 1.397 F 0.051 REF 1.295 REF G 0.100 BSC 2.540 BSC H 0.539 0.579 13.691 14.707 J 0.125 MAX 3.175 MAX K 0.050 REF 1.270 REF L 0.000 0.010 0.000 0.254 M 0.088 0.102 2.235 2.591 N 0.018 0.026 0.457 0.660 P 0.058 0.078 1.473 1.981 R S 0.116 REF 2.946 REF U 0.200 MIN 5.080 MIN V 0.250 MIN 6.350 MIN /C0095 /C0095 OPTIONAL CHAMFER

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. MCT7800/D /C0042/C0077/C0067/C0084/C0055/C0056/C0048/C0048/C0047/C0068/C0042 ◊ 1PHX33530-3 PRINTED IN USA (8/94) MPS/POD LINEAR YCAAAA