T6311A TMT | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 9

Technical content

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P. 1 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C Low-Dropout, Constant-Current White LED Bias Supply

FEATURES

  • Low 200mV Dropout at 9mA
  • Up to 150mA LED Bias Current
  • 0.3% LED Current Matching
  • Simple LED Brightness Control
  • Low 40uA Supply Current
  • Low 0.05uA Shutdown Current
  • 2.5V to 5.5V Supply Voltage Range
  • SOP-8 and SOT23-6 Package
  • Output channel : SOP-8 package for four channel SOT23-6 package for three channel

Applications

  • Cellular Phones
  • Portable Communication Devices
  • Handheld Electronics
  • Digital Cameras
  • PDAs
  • LED/Display Back Light Driver
  • LEDs for Camera Flash PART NUMBER EXAMPLES GRNERAL DESCRIPTION The T6311A low-dropout bias supply for white LEDs is a high-performance alternative to the simple ballast resistors used in conventional white LED designs. The T6311A uses a single resistor to set the bias current for four LEDs, which are matched to 0.3%. The T6311A consumes only 40uA of supply current when enabled and 0.05uA when disabled. The T6311A advantages over ballast resistors include significantly better LED to LED bias matching, much lower bias variation with supply voltage variation, significantly lower dropout voltage, and in some applications, significantly improved efficiency. The T6311A requires a 200mV dropout at a 9mA load on each output to match the LED brightness. The T6311A is available in SOP-8 and SOT23-6 package. PART NO. PACKAGE T6311A-D SOP-8 T6311A-X SOT23-6

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.2 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C PIN ARRANGEMENT(Top view) SOT23-6 SOP-8 GND EN SET 3 4 LED1 LED2 LED3 GND EN SET 3 6 LED1 LED2 LED3 NC4 5LED4 PIN DESCRIPTION Pin no. SYMBO L SOP-8 SOT23-6

DESCRIPTION

Enable Input/Power Input. Drive high (> 2.5V) to enable; drive low (< 2.2V) to disable. When disabled, SET, LED1, LED2, LED3 and LED4 are high impedance. When enabled, EN is the power input for the T6311A. GND 7 2 Ground SET 6 3 Bias Current Set Input. The current flowing into SET sets the bias current into each LED by ILED_= 240 x ISET. VSET is internally biased to 1.2V. SET is high impedance when EN is low. NC 5 - No connection. LED4 4 - LED 4 Cathode Connection. Current flowing into LED4 is 240 times the current flowing into SET. LED4 is high impedance when EN is low. LED3 3 4 LED 3 Cathode Connection. Current flowing into LED3 is 240 times the current flowing into SET. LED3 is high impedance when EN is low. LED2 2 5 LED 2 Cathode Connection. Current flowing into LED2 is 240 times the current flowing into SET. LED2 is high impedance when EN is low. LED1 1 6 LED 1 Cathode Connection. Current flowing into LED1 is 240 times the current flowing into SET. LED1 is high impedance when EN is low.

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.3 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C BLOCK DIAGRAM EN REF LED3 GND LED2 LED1 SET ON OFF RSET VCTRL LED4 current controller Fig. 1

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.4 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C ABSOLUTE MAXIMUM RATINGS Parameter Symbol Value Unit Voltage on any pin relative to GND V IN -0.3 to 6 V Operating Temperature Rang T A -40 to +85 °C Maximum Soldering Temperature (at leads, 10 sec) T LEAD 300 °C Storage Temperature Rang T S -65 to +150 °C Continuous Power Dissipation ( TA = +70°C ) 1 W

Electrical Characteristics

(TA = -40 to 85°C unless otherwise noted. Typical values are at TA =25°C, VEN =3.3V, VLED1 = VLED2= VLED3= VLED4= 1V) (Note 1) Symbol Description Conditions Min. Typ. Max Unit VEN Operating voltage range EN is power supply input 2.5 5.5 V ISET SET input current range 5 260 uA SET to LED current ratio I LED / ISET, ISET=42uA 220 240 260 A/A VSET SET bias voltage I SET=42uA 1.08 1.2 1.32 V TA= -40 to +25°C 0.01 1 uA SET leakage current in Shutdown EN=GND, VSET=3.3V TA= -40 to +85°C 5 uA LED to LED current matching I SET=42uA 0.3 % ILED Maximum LED sink current Each LED 100 150 mA ISET=20uA (Note 2) 100 180 mV ISET=40uA (Note 3) 200 360 mV LED dropout voltage ISET=80uA (Note 3) 230 410 mV LED leakage current in shutdown VLED1=VLED2=VLED3=VLED4= 3.3V, EN=GND, TA=+25°C, each LED 0.01 1 uA VIH Input high voltage V EN >VIH for enable 2.5 V VIL Input low voltage V EN <VIL for disable 2.2 V VEN = 2.50V to 5.5V, EN is power supply input 40 100 uA IEN EN intput bias current VEN = 0.4V, TA=+25°C 0.05 1 uA Note 1: Limits are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed through correlation using statistical quality control (SQC) methods. Note 2: Dropout Voltage is defined as the LED to GND voltage at which current sink into LED drops 20% from the value at VLED = 1V. Note 3: Dropout Voltage is defined as the LED to GND voltage at which current sink into LED drops 10% from the value at VLED = 1V.

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.5 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C Typical Operating Characteristics TBD

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.6 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C Functional Description The T6311A provides constant current bias supply for white LED designs. The T6311A uses a single resistor to set the bias current for up to three LEDs. LED bias currents are matched to 0.3% by the T6311A current matching architecture (Fig. 1). Supply current EN) is a low 40uA in normal operation and 0.05uA when disabled. The T6311A offers several advantages over using ballast resistors, such as improved LED to LED brightness matching, lower bias variation with supply voltage changes, significantly lower dropout voltage, and in some applications, significantly improved efficiency. The T6311A achieves a 200mV dropout with a 9mA load on each output. For circuits requiring only one or two LEDs, leave unused LED outputs unconnected. Enable Input EN powers the input of the T6311A. Drive EN high (> 2.5V) to enable the device; drive EN low (< 2.2V) to disable the device. When driven high, EN draws 40µA to power the IC. Driving EN low forces LED1, LED2, LED3, LED4 and SET into a high-impedance state. Setting the Output Current SET controls the LED bias current. Current flowing into LED1, LED2, LED3 and LED4 is 240 times greater than the current flowing into SET. Set the output current as follows: I LED = 240 ( (VCTRL - VSET) / RSET ) where V SET = 1.2V, V CTRL is an external voltage between 1.8V and 5.5V, and RSET is the resistor connected between V CTRL and SET (Fig. 1). Applications Information Very Low-Cost, High-Efficiency Solution (Fig. 2). A battery (single Li+ or three NiMH cells) powers the LEDs directly. This is the least expensive and most efficient architecture. Due to the high forward voltage of white LEDs (3.3V), the LED brightness may dim slightly at the end of battery life. The T6311A current regulating architecture and low dropout greatly minimize this effect compared to using simple ballast resistors. The enable function of the T6311A turns on and off the LEDs. An existing low-dropout regulator is used as V CTRL. Brightness Adjustment Using a DAC (Fig. 3). A DAC is used as V CTRL such that the LED brightness may be dynamically adjusted to eliminate factory calibration. A battery (single Li+ or three NiMH cells) or a regulated power source drives the LEDs.

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.7 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C TYPICAL APPLICATION CIRCUITS GND SET ON EN To ot he r circuit s LED3 V CTRL OF F LED2LED1 E x istin g LDO LED4 Fig. 2 Very low-cost, high-efficiency solution GND SET ON EN LED3 V CTRL OFF LED2LED1 DAC LED4 Fig. 3 Brightness adjust using DAC

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.8 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C PACKAGE DIMENSIONS 8-LEAD SOP A1 A B CC1 D E F H C2 0.10 - 0.25 0.001 - 0.004 H 0~8 ° 0~8 °

CHtm Preliminary Product spec. T6311A TM Technology Inc. reserves the right P.9 Publication Date: JUN. 2005 to change products or specifications without notice. Revision: C PACKAGE DIMENSIONS SOT23-6 A1 A B CC1 D E F GHI B1 1.90(BSC) 0.075(BSC) B2 0.95(BSC) 0.037(BSC) C2 0 0.075 0.150 0 0.003 0.06 D 0.40 0.015 G 0.60(REF) H 0~8 ° 0~8 ° I 5~15 ° 5~15 °