T60404-P4640-X156

T60404-P4640-X156 VACUUMSCHMELZE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Item no.:T60404-P4640-X156 K-no.: 26654 1000 A Current Sensor for ±24V- Supply Voltage Date 25.11.2016 Customer: Standard Type Customer Part number Seite 1 von 6 Hrg MC-PD editor Bearb: designer Ockajak MC-PM: Sn. check freig.: BEF released Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten V A C U U M S C H M E LZ E for electric current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Electrical data IPN Primary nominal r.m.s. current 1000 A R M 1 Measuring resistance 0 ... 100 Ω ISN Secondary nominal r.m.s. current 200 mA KN Turns ratio (1): 5000 1 connected to sensor output, R M for IP,max see fig. 1 on page 2 Accuracy – Dynamic performance data min. typ. max. Unit IP,max 2 Max. measuring range @ R M = 10 Ω ; T A= 25°C 2500 - - A @ R M = 10 Ω ; T A= 85°C 2150 - - A X Accuracy @ I PN , T A= -40 ... +85°C - - 0.4 % εL Linearity - - 0.1 % I0 Offset current @ I P=0, T A= 25°C - - 0.1 mA I0H Hysteresis current - - 0.1 mA tr Response time @ 80% of I PN - < 1 - µs tra Reaction time @ 10% of I PN (di/dt = 1200 A/ µs) - - 1 µs fBW Frequency bandwidth DC…100 - - kHz 2currents with high slew rates can be measured above I P,max (transformer behavior) General data min. typ. max. Unit ϑA Ambient operating temperature -40 - +85 °C ϑS Ambient storage temperature -40 - +85 °C m Mass - 550 - g U C Supply voltage ±21.60 ±24 ±25.2 V IC0 Current consumption for Ip = 0A - 27 - mA ICN Current consumption for I PN = 1000A - 190 - mA * s clear Clearance 20 - - mm * s creep Creepage 20 - - mm * U sys System voltage (determines impulse voltage acc. table 7) - - 1000 V RMS * U AC Working voltage (acc. U ACL as limit in table 3) 1000 V RMS - - 1500 V DC * U PD Rated discharge voltage (acc. table 24 with U PD =U ACP ) - - 1414 V peak Max. potential difference acc. to UL 508 - - 1000 Vrms * Constructed and manufactored and tested in accordance with EN 61800-5-1:2007 (Pin 1 - 3 to primary opening) Reinforced insulation, Insulation material group 1, Pollution degree 2, Overvoltage category III Date Name Issue Amendment 25.11.16 Ku 81 Typo: Page 2, Table 55°C/1 Ω/2880A changed Dwell time from <10min to <3min. minor change.

Item no.:T60404-P4640-X156 K-no.: 26654 1000 A Current Sensor for ±24V- Supply Voltage Date 25.11.2016 Customer: Standard Type Customer Part number Seite 2 von 6 Hrg MC-PD editor Bearb: designer Ockajak MC-PM: Sn. check freig.: BEF released Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten V A C U U M S C H M E LZ E for electric current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Capability of the sensor for measuring max. peak currents at defined temperatures, values for supply voltage ±22.80 V (±24 V -5 %): ϴA 55 °C 55 °C 55 °C 55 °C 85°C 85°C 85°C 85°C R M 1 Ω 5 Ω 20 Ω 50 Ω 1 Ω 5 Ω 20 Ω 50 Ω IP,max 2880A 2610A 1930A 1270A 2610A 2390A 1810A 1220A Dwell time < 3min < 10min < 10min < 30min < 3min < 3min < 3min < 15min Limit curve of measurable current Î P=f(R M ), values for supply voltage ±22.80 V (±24 V -5 %) Fig. 1: I P,max = f(R M ) @ ϑA Absolute maximum conditions: ϴA < 70 °C 70 °C < ϑA ≤ 85 °C I P = I P,max up to 1800 A DC 1200 A DC Stresses above these conditions may cause permanent damage. Exposure to absolute maximum rating conditions for extended periods will degrade device reliability and lifetime expectancy. Functional operation of the device at these or any other conditions beyond those specified in this specification is not permitted.

Item no.:T60404-P4640-X156 K-no.: 26654 1000 A Current Sensor for ±24V- Supply Voltage Date 25.11.2016 Customer: Standard Type Customer Part number Seite 3 von 6 Hrg MC-PD editor Bearb: designer Ockajak MC-PM: Sn. check freig.: BEF released Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten V A C U U M S C H M E LZ E for electric current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Overload puls (µs-range) Fig. 2: Output current reaction of a 3kA current pulse with R M = 10 Ω Schematic diagram: R M 3 +Vc PIN 2 (Iout ) PIN 1 (+Uc) PIN 3 (-Uc)

Item no.:T60404-P4640-X156 K-no.: 26654 1000 A Current Sensor for ±24V- Supply Voltage Date 25.11.2016 Customer: Standard Type Customer Part number Seite 4 von 6 Hrg MC-PD editor Bearb: designer Ockajak MC-PM: Sn. check freig.: BEF released Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten V A C U U M S C H M E LZ E for electric current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Arrow shows positive current direction Marking Explanation: Item number: see Tab.2 (left column) F = Factory code DC = Date code Example: Sensor with end number X152 Produced in Slovakia in April 2015 Part number: 4640-X152 Factory code: SK Date code: F4 Mechanical outline (mm): * General tolerances DIN ISO 2768-c 100 Ø4,2 Ø5,3 4 x Ø2,25 10 tief 0,3 3,3 40,5 110 34 0,3 Ø5,3 Verguß (potting) DC =Date Code F =Factory Beschriftung (marking) Ip Prüfmaß (test dimension) 94,8 40,5 Ip 1 1 2 3 Connector: JST BH03B-XASK-BN Pin 1: +U C Pin 2: I Out Pin 3: -U C

1 Ip: Positive current

4640-“Item number“ “ F” “DC” 4640-X152“ SK F4

Item no.:T60404-P4640-X156 K-no.: 26654 1000 A Current Sensor for ±24V- Supply Voltage Date 25.11.2016 Customer: Standard Type Customer Part number Seite 5 von 6 Hrg MC-PD editor Bearb: designer Ockajak MC-PM: Sn. check freig.: BEF released Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten V A C U U M S C H M E LZ E for electric current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Offset ripple reduction The offset ripple can be reduced by an external low pass. The simplest solution is a passive low pass filter of 1st order by connecting a capacitor parallel to the burden resistor R M as shown on page 3. The required capacitance can be calculated as follows: In this case the response time is enlarged. It is calculated from: aMrr CRtt 5 , 2+≥′ Routine Test (Measurement after temperature balance of the samples at room temperature; SC = significant characteristic) KN (N 1/N 2) (100%) M3011/6 Transformation ratio (I PN =1000A, 40-80 Hz) 1 : 5000 ± 0.4 % (SC) I0 (100%) M3226 Offset current < 0.1 mA (SC) U P (100%) M3014 Test voltage (1s) (RMS) 4.0 kV (SC) Pin 1 - 3 to primary opening U PDE (AQL 1/S4) Partial discharge voltage (extinction) (RMS) 1500 V U PD(rms) ·1.875 * acc. table 24 (RMS) 1875 V Type Test (Pin 1-3 to primary opening) Û W M3064 HV transient test, * acc. table 18, 19 12 kV (1.2 µs / 50 µs-wave form) U P M3014 Test voltage (5s) (RMS) 6 kV U PDE Partial discharge voltage (extinction) (RMS) 1500 V U PD(rms) ·1.875 * acc. table 24 (RMS) 1875 V ESD EN 61000-4-2 contact / surface ±8 / ±15 kV * IEC61800-5-1:2007. Applicable documents Constructed, manufactured and tested in accordance with IEC61800-5-1:2007. Further standards: UL 508 ; file E317483, category NMTR2 / NMTR8 gM a fRC ⋅⋅= π2

Item no.:T60404-P4640-X156 K-no.: 26654 1000 A Current Sensor for ±24V- Supply Voltage Date 25.11.2016 Customer: Standard Type Customer Part number Seite 6 von 6 Hrg MC-PD editor Bearb: designer Ockajak MC-PM: Sn. check freig.: BEF released Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten V A C U U M S C H M E LZ E for electric current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit) Explanation to parameters used in this datasheet Accuracy Xtotal (I PN ): The sum of all possible errors over the temperature range by measuring a current I PN : X: Permissible measurement error in the final inspection at RT. I SB is the DC output current for a DC primary current with the same value as the (positive) rated current I PN (with I O = 0) X Ti : Temperature drift of the rated value orientated output term. I SN (cf. Notes on F i) in a specified temperature range: I SB is the secondary current at temperature ϑA1 or ϑA2 εL: Linearity fault where I P is any input DC and I Sx the corresponding output term. (I O = 0). Offset and drift IOH : Zero variation after overloading with a DC of tenfold the rated value (R M = R MN ) I Ot : Long term drift of I O after 100 temperature cycles in the range -40 to 85 °C. Dynamic properties tra Reaction time, measured as a delay time between a rectangular primary current (di/dt ≈ 1200A/µs) and the output current I S at I P = 0.1 * I PN t r: Response time, measured as a delay time between a rectangular primary current and the output current I S at I P = 0.9 * I PN Voltage ratings (according to IEC 61800-5-1:2007) UPD Rated discharge voltage (recurring peak voltage separated by the insulation) U sys System voltage: RMS value of rated voltage U AC Working voltage: RMS voltage which occurs by design in a circuit or across an insulation ( ) ( ) SN A1 SB A2 SB Ti I II100 ϑϑ −⋅=X SN Sx PN P L I I I I100 −⋅=ε ( ) 1IK I I100 X PN N PN S total −⋅⋅= I100 X SN SB −⋅=