T550B107K008FT

T550 KEMET | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 17

Technical content

1© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Built Into Tomorrow Benefits

• I ncludes F-Tech anode which eliminates hidden defects in the dielectric 00% simulated breakdown screening M aximum operating temperature of +105°C
• DLA drawing 13030 qualified parts available P olymer cathode technology E xtremely low ESR H igh frequency and low temperature capacitance retention 00% constant voltage conditioning (240 hours) 00% surge current tested
• Volumetrically efficient
• Non -ignition failure mode A pproximately 25% lighter than equivalent wet tantalum T 555 surface mount design (see dimensions diagram) Overview The T550 axial leaded and T555 surface mount polymer hermetically sealed (PHS) devices are tantalum capacitors with a Ta anode and Ta 2O5 dielectric. A conductive organic polymer replaces the traditionally used MnO2 or wet electrolyte as the cathode plate of the capacitor. This results in very low ESR and improved capacitance retention at high frequency and low temperature. The PHS device also exhibits a benign failure mode, which eliminates the case breach that can occur in wet tantalum capacitors. Additionally, this part may be operated at voltages up to 80% of rated voltage, with equivalent or better reliability than traditional MnO 2 or wet tantalum capacitors operated at 50% of rated voltage. PHS capacitors also offer higher ripple current handling capability and a lower ESR range than wet tantalums. With reduced ESR and enhanced capacitance retention at higher frequencies and low temperatures, these parts provide the highest total capacitance and the most economical solution for high power applications, all within an approximately 25% lighter package than the equivalent wet tantalum capacitor. Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C

Applications

Typical applications include high voltage power management, such as buck/boost converters, filtering, hold-up capacitors, a nd other high ripple current applications.

2© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C

Ordering Information

T 550 B 107 M 025 A T 4251 Capacitor Class Series Case Size Capacitance Code (pF) Capacitance Tolerance Rated Voltage (VDC) Product Level Termination Finish Surge Option Packaging T = Tantalum 550 = Axial Leaded PHS 555 = Surface Mount PHS B C First two digits represent significant fi gures. Third d igit specifies n umber of zeros. K = ±10% M = ±20% 006 = 6.3 008 = 8 010 = 10 015 = 15 025 = 25 030 = 30 035 = 35 040 = 40 050 = 50 060 = 60 075= 75 100 = 100 A = N/A B* = DLA 13030 standard reliability T* = DLA 13030 high reliability E* = DLA 13030 "B" level equivalent for T termination F* = DLA 13030 "T" level equivalent for T termination T = 100% tin (Sn)- plated H = Tin/lead (SnPb) solder coated (5% Pb minimum) Blank = 25°C ±5°C, 10 cycles, after constant voltage conditioning (KEMET standard) 4251 = 10 cycles, –55°C and +85°C after constant voltage conditioning 4252 = 10 cycles, –55°C and +85°C before constant voltage conditioning Blank = Bulk/Sleeved 0100 = Bulk/ Unsleeved 7200 = Tape & Reel/ Sleeved 7293 = Ammo/Sleeved 7443 = Ammo/Sleeved * Only available on select parts. Refer to part number table for details. ** Only for T550 (Surge options/Packaging) Ordering Information – DLA 13030 -01 K A S L B Drawing Number Dash Number Capacitance Tolerance Surge Current Testing Insulation Lead Length Product Level See Part Number Table K = ±10% M = ±20% A = +25°C ±5°C, 10 cycles, after constant voltage conditioning (KEMET standard) B = –55°C, –5°C, +0°C and +85°C ±5°C after constant voltage conditioning. C = –55°C, –5°C, +0°C and +85°C ±5°C before constant voltage conditioning. S = Sleeved U = Unsleeved L = 1.50 inches (standard) B = Standard reliability T = High reliability * Standard terminations for DLA part numbers is "H" (SnPb). Performance Characteristics Item Performance Characteristics Operating Temperature −55°C to 105°C Rated Capacitance Range 20 680 μF at 120 Hz/25°C Capacitance Tolerance K tolerance (±10%), M tolerance (±20%) Rated Voltage Range 6.3 – 100 V DF (120 Hz at 25°C) Refer to Part Number Electrical Specification Table E SR (100 kHz at 25°C) Refer to Part Number Electrical Specification Table L eakage Current Refer to Part Number Electrical Specification Table (rated voltage up to +85°C and 78% of rated voltage applied at 105°C) Packaging T550 according to MIL-PRF-39006, T555 bulk KEMET does not recommend storage above 85°C. * Additional case sizes and capacitance/voltage are under development.

3© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Qualification - T550 Test Performed Method Reference Test Conditions Reliability and Environmental Tests AC Ripple Life at 85˚C MIL –PRF–39006 85˚C, 40 kHz ripple current, 2,000 hours 85˚C Life KEMET Standard 85˚C, rated voltage, 2,000 hours 105˚C Life KEMET Standard 105°C, 0.78 x rated voltage, 2,000 hours Surge Voltage MIL –PRF–39006 85˚C, 1.15 x rated voltage, 1,000 cycles, except delta cap shall be +10%/−20% Surge Current MIL –PRF–39003 +25 °C, 10 cycles (Option A), Option B available Low Temperature Storage MIL –PRF–39006 −62˚C for hours followed by hour at 125˚C Reverse Voltage KEMET Catalog 1 V for 8 hours maximum at 25°C, 1 V for 2 hours maximum at 70°C Physical, Mechanical and Process Tests Visual and Mechanical Examination (Internal and External) MIL –PRF–39006 Case dimensions, marking Terminal Strength MIL –PRF–39006 Pull test and wire lead bend test Resistance to Solvents MIL –PRF–39006 Immersion in (3) solvents Resistance to Soldering Heat MIL –PRF–39006 Immersed to within 0.05 inch of capacitor body Solderability MIL –PRF–39003 Depth of insertion in flux and solder to within 0.125 inch ±0.025 inch (3.18 mm ± 0.64 mm) from end of case and from the point of “clean lead” emerging from the seal eyelet. Shock and Vibration MIL –STD–202, Methods 213, 204 Shock Method 213, Condition I, 100 G peak, Vibration Method 204, Condition D, 20 G peak Barometric Pressure (Reduced) MIL –PRF–39006 150,000 feet for 5 minutes, voltage applied for 1 minute Salt Atmosphere (Corrosion) MIL –PRF–39006 Subjected to fine mist of salt solution Moisture Resistance MIL –PRF–39006 65°C at 6 V Dielectric Withstanding Voltage MIL –PRF–39006 2,000 VDC, 60 seconds, sleeving examined for evidence of breakdown Insulation Resistance MIL –PRF–39003 500 VDC, minute, insulation resistance not less than 1,000 MΩ Electrical Characterization Temperature Stability Reference MIL –PRF–39006 −55˚C to 105˚C Frequency Scan KEMET Standard Impedance, ESR and capacitance versus frequency

4© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Qualification – DLA Approval Inspection – Only for T550 Inspection Test Name DLA Requirement Paragraph SS/Lot Group I Shock (specified pulse)1 3.3.4 6 per case size Vibration, high frequency 1 3.3.5 Thermal shock 3.3.6 Salt atmosphere 3.3.7 Group II Solderability 3.3.8 Terminal strength 3.3.9 Surge voltage 2 3.3.10 Moisture resistance 3.3.11 Dielectric withstanding voltage 3.3.12 Insulation resistance 3.3.13 Low temperature (storage) 3.3.14 Group III Stability at low and high temperatures 3.3.15 13 Reverse voltage 3.3.23 12 per condition Group IV Life at 85°C 3.3.16 102 Group V AC ripple life at 85°C 3.3.18 8 per case size Group VI Life at 105°C 3.3.17 Barometric pressure 3.3.20 Group VII Resistance to solvents 3.3.21 Resistance to soldering heat 3.3.22 1 No failures for mechanical shock or vibration tests shall be permitted. 2 Surge voltage change in capacitance limits are wider than those in some subsequent tests. It may be necessary to perform initial measurements again, prior to the individual tests of Group II. Product Level: Inspection of product for delivery shall consist of: B level Group A inspection specified in Drawing 13030 T level Group A and group B inspections specified in Drawing 13030

5© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Qualification - T555 Test Performed Method Reference Test Conditions Reliability and Environmental Tests 105˚C Life K EMET Standard 105°C, 0.78 x rated voltage, 2,000 hours Surge Voltage MIL-PRF-39006 85˚C, 1.15 x rated voltage, 1,000 cycles, except delta cap shall be +10%/–20% Physical, Mechanical and Process Tests Visual and Mechanical Examination (Internal and External) MIL-PRF-39003 Case dimensions, marking Terminal Strength MIL-PRF-39006 Pull test and wire lead bend test Resistance to Solvents MIL-PRF-39006 Immersion in (3) solvents Resistance to Soldering Heat MIL-PRF-39006 Immersed to within 0.05 inch of capacitor body Solderability MIL-PRF-39006 Depth of insertion in flux and solder to within 0.062 inch of welded joint Shock and Vibration MIL-STD-202, Methods 213, 204 Shock Method 213, Condition I, 100 g peak, Vibration Method 204, Condition D, 20 g peak Electrical Characterization Temperature Stability Reference MIL-PRF-39006 –55˚C to 105˚C Environmental Compliance Epoxy compliant with UL 94 V–0.

6© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C

Electrical Characteristics

ESR vs. Frequency Capacitance vs. Frequency 100 120 10 100 1, 000 10,000 100,000 1, 000,000 Capacitance (µF) Frequency (Hz) +125°C +85°C +50°C +25°C 0°C −25°C −55°C −80°C 0.0 0.1 1.0 10.0 10 100 1, 000 10,000 100,000 1, 000,000 10,000,000 ESR (Ohms) Frequency (Hz) +125°C +85°C +50°C +25°C 0°C −25°C −55°C −80°C

7© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Dimensions – Inches (Millimeters) T550 SIDE VIEW END VIEW L M 1.50 ±0.250 (38.10 ±6.35) D J 0.094 (2.39) Maximum Case Code Uninsulated Case Insulated Case L ±0.031 (0.79) D +0.016 (0.41) −0.015 ( 0.38) M ±0.002 (0.05) J maximum D +0.016 (0.41) −0.015 ( 0.38) L ± 0.031 (0.79) Dimensions – Millimeters T555 H F A L SIDE VIEW BOTTOM VIEWCATHODE (−) END VIEW W S S Case Code Weight (g) B

8© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Table 1A – Ratings & Part Number Reference Rated V o l t a g e Rated Capacitance Case Size KEMET Part Number DLA Drawing Number DC Leakage DF Maximum ESR Ripple Current (V) 85°C µF KEMET/EIA (See below for part options) (See below for part options) µA at 25°C Maximum/

5 Minutes

% at 25°C

120 Hz Max

mΩ at 25°C 100 kHz mArms at 85°C/40 kHz 6.3 140 B T550B147(1)006A(3) N/A 6.3 5.0 120 1,510 8 220 B T550B227(1)008A(3) N/A 13.2 5.0 120 1,510 8 680 B T550B687(1)008A(3) N/A 40.8 5.0 90 1750 10 100 B T550B107(1)010A(3) N/A 7.5 5.0 140 1400 10 180 B T550B187(1)010A(3) N/A 13.5 5.0 110 1580 10 560 B T550B567(1)010A(3) N/A 42.0 5.0 90 1750 15 70 B T550B706(1)015A(3) N/A 7.9 5.0 140 1400 15 120 B T550B127(1)015A(3) N/A 13.5 5.0 110 1580 15 390 B T550B397(1)015A(3) N/A 43.9 5.0 90 1750 25 50 B T550B506(1)025A(3) N/A 9.4 5.0 170 1275 25 100 B T550B107(1)025(2)H 13030-01(1)(4)(5)L(6) 18.8 5.0 190 1,200 25 100 B T550B107(1)025A(3) N/A 18.8 5.0 190 1,200 30 40 B T550B406(1)030A(3) N/A 9.0 5.0 170 1,275 30 68 B T550B686(1)030A(3) N/A 15.3 5.0 140 1,400 35 330 B T550B337(1)035A(3) N/A 86.6 10.0 180 1,240 35 500 B T550B507(1)035A(3) N/A 86.6 10.0 110 1,240 40 100 B T550B107(1)040(7)T N/A 30.0 5.0 150 1,350 40 120 B T550B127(1)040(7)T N/A 36.0 5.0 120 1,510 50 25 B T550B256(1)050A(3) N/A 9.4 5.0 170 1,275 50 47 B T550B476(1)050A(3) N/A 17.6 5.0 150 1,350 50 100 B T550B107(1)050(7)T N/A 37.5 5.0 130 1,450 50 120 B T550B127(1)050(7)T N/A 45.0 5.0 90 1,750 50 300 C T550C307(1)050A(3) N/A 112.5 7.0 100 1,460 60 20 B T550B206(1)060A(3) N/A 9.0 5.0 200 1,175 60 39 B T550B396(1)060A(3) N/A 17.6 5.0 160 1,310 60 100 B T550B107(1)060(7)T N/A 45.0 5.0 100 1,660 75 75 B T550B756(1)075(7)T N/A 42.2 5.0 110 1,580 75 82 B T550B826(1)075A(3) N/A 57.6 5.0 220 1,800 100 25 B T550B256(1)100(7)T N/A 18.8 5.0 190 1,200 (1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance. (2) To complete KEMET part number, insert A = N/A, B = standard reliability, or T = high reliability. (3) To complete KEMET part number, insert T = 100% matte tin (Sn)-plated, H = standard solder coated (SnPb 5% Pb minimum). Designates termination finish. (4) To complete the DLA PIN number, insert the surge current testing option, A = 25°C after voltage aging, B = − 55°C +0°C and +85°C after voltage aging or C = −55°C +0°C and +85°C before voltage aging. (5) To complete the DLA PIN number, insert the insulation option. S = Sleeved, U = Unseleeved. (6) To complete the DLA PIN number, insert the product level option. B = standard reliability or T = high reliability. (7) To complete KEMET part number, insert E = DLA "B" level equivalent, or F = DLA "T" level equivalent. Designates product level To confirm availability on DLA part numbers marked in blue font, please contact your KEMET sales representative Refer to Ordering Information for additional detail. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked with the higher voltage rating. The 85°C 40 kHz ripple limit is based on the maximum allowed power at 85°C and the maximum expected ESR at 40 kHz. For this calculation, the 100 kHz ESR limit is multiplied by a factor of 1.3 to account for the frequency dependence of ESR.

9© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Table 1B – Ratings & Part Number Reference Rated Vo l t a g e Rated Capacitance Case Size KEMET Part Number DC Leakage DF Maximum ESR Ripple Current (V) 85°C µF KEMET/EIA (See below for part options) µA at 25°C Maximum/ % at 25°C mΩ at 25°C 100 kHz mArms at 85°C/40 kHz 6.3 140 B T555B147(1)006A(3) 6.3 5.0 120 1,510 8 220 B T555B227(1)008A(3) 13.2 5.0 120 1,510 8 680 B T555B687(1)008A(3) 40.8 5.0 90 1,750 10 100 B T555B107(1)010A(3) 7.5 5.0 140 1,400 10 180 B T555B187(1)010A(3) 13.5 5.0 110 1,580 10 560 B T555B567(1)010A(3) 42.0 5.0 90 1,750 15 70 B T555B706(1)015A(3) 7.9 5.0 140 1,400 15 120 B T555B127(1)015A(3) 13.5 5.0 110 1,580 15 390 B T555B397(1)015A(3) 43.9 5.0 90 1,750 25 50 B T555B506(1)025A(3) 9.4 5.0 170 1,275 25 100 B T555B107(1)025A(3) 18.8 5.0 190 1,200 30 40 B T555B406(1)030A(3) 9.0 5.0 170 1,275 30 68 B T555B686(1)030A(3) 15.3 5.0 140 1,400 35 330 B T555B337(1)035A(3) 86.6 10.0 180 1,240 35 500 B T555B507(1)035A(3) 86.6 10.0 110 1,580 40 100 B T555B107(1)040A(3) 30.0 5.0 150 1,350 40 120 B T555B127(1)040A(3) 36.0 5.0 120 1,510 50 25 B T555B256(1)050A(3) 9.4 5.0 170 1,275 50 47 B T555B476(1)050A(3) 17.6 5.0 150 1,350 50 100 B T555B107(1)050A(3) 37.5 5.0 130 1,450 50 120 B T555B127(1)050A(3) 45.0 5.0 90 1,750 60 20 B T555B206(1)060A(3) 9.0 5.0 200 1,175 60 39 B T555B396(1)060A(3) 17.6 5.0 160 1,310 60 100 B T555B107(1)060A(3) 45.0 5.0 100 1,660 75 75 B T555B756(1)075A(3) 42.2 5.0 110 1,580 75 82 B T555B826(1)075A(3) 57.6 5.0 220 1,800 100 25 B T555B256(1)100A(3) 18.8 5.0 190 1,200 (1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance. (3) To complete KEMET part number, insert T = 100% Matte Tin (Sn)-plated, H = Standard Solder coated (SnPb 5% Pb minimum). Designates termination finish. Refer to Ordering Information for additional detail. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked with the higher voltage rating. The 85°C 40 kHz ripple limit is based on the maximum allowed power at 85°C and the maximum expected ESR at 40 kHz. For this calculation, the 100 kHz ESR limit is multiplied by a factor of 1.3 to account for the frequency dependence of ESR.

10© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Recommended Voltage Derating Guidelines 20% 40% 60% 80% 100% 120% −55 25 45 85 105 % Working Voltage Temperature (°C) % Change in working DC voltage with temperature Recommended maximum application voltage (as % of rated voltage) 80% 78% 63% −55°C to 85°C 8 5°C to 105°C % Change in working DC voltage with temperature VR 78% of VR Recommended maximum application voltage (as % of rated voltage) 80% of VR 63% of VR Ripple Current/Ripple Voltage Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the device. Permissible AC ripple voltage that may be applied is limited by two criteria: . The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor. The negative peak AC voltage in combination with bias voltage, if any, must not exceed the allowable limits specified f or reverse voltage. The maximum power dissipation by case size can be determined using the below left table. The maximum power dissipation rating stated in the table must be reduced with increasing environmental operating temperatures. Refer to the below right table for temperature compensation requirements. Case Code Maximum Power Dissipation (Pmax) mWatts at 25°C with +60°C Rise KEMET B* 715 C 894 * Applies to TH and SMD Temperature Compensation Multipliers for Maximum Power Dissipation (Pmax) T ≤ 45°C 45°C < T ≤ 85°C 85°C < T ≤ 105°C 1.00 0.70 0.10 T = Environmental temperature Using the Pmax of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = √Pmax /R E(max) = Z √Pmax /R I = rms ripple current (amperes) E = rms ripple voltage (volts) P max = maximum power dissipation (watts) R = ESR at specified frequency (ohms) Z = Impedance at specified frequency (ohms) The maximum power dissipation rating must be reduced with increasing environmental operating temperatures. Refer to the Temperature Compensation Multiplier table for details.

11© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Reverse Voltage Solid tantalum polymer capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. A small reverse voltage is permissible for time periods per the below table. KEMET can offer lower capacitance in this voltage with higher reverse voltage capability. In addition, we continue to improve our capability for this characteristic. Temperature Permissible Reverse Voltage 25°C 1 V for 8 hours maximum 70°C 1 V for 2 hours maximum Table 2 – Land Dimensions/Courtyard KEMET Metric Size Code Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) Case EIA W L S V1 V2 W L S V1 V2 W L S V1 V2 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC–7351). L S W W L Grid Placement Courtyard

12© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Soldering Process 025 100 125 150 175 200 225 250 1 2 3 Time (Minutes) Degrees – Cº 4 5 6 Flux Zone Preheat Zone Entrance to Solder Wave Exit from Solder Wave Hot Air Debridging Exit from Solder Machine (Time in Wave – 2 to 4 Seconds) Solder Wave Peak Temperature 260ºC Entrance to Solder Machine 80ºC to 120ºC Bottom Side Temperature Range Top Side Nominal 150ºC Maximum Free Air Cool Entrance to In-Line Cleaner Exit from In-Line Cleaner (time in cleaner may be less) Immersion in Cleaning Vapor Manual Solder Profile with Pre-heating Gradual Preheat 60 – 120 Seconds Recommend 2.5°C/second Soldering Maximum 3 seconds Delta T < = 120ºC Gradual Cooling Optimum Solder Wave Profile H and Soldering (Manual)* *T555 MUST be hand soldered only. Mounting WARNING: T555/T556 MUST BE HAND SOLDERED. THE USE OF STANDARD SMD PROCESSES FOR BOARD MOUNT WILL CAUSE IRREVERSIBLE DAMAGE TO THIS PRODUCT. T555 SMD In hand-soldering tantalum polymer SMT capacitors, a manufacturer can utilize two (2) soldering methodologies that include pre-heating or not pre-heating the capacitors. KEMET recommends utilizing a pre-heating technique. However, due to the large temperature gradient between the capacitors and the tip of the soldering iron, take extreme caution in this process. The thermal stresses from the large thermal gradients and the propensity of the operator touching the tip of the soldering iron to the device can lead to mechanical and/or electrical damage. When manually soldering, it is important the soldering process be carefully monitored and carried out so that the temperature gradient falls within the recommended conditions above (profile).

13© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Mounting cont. Process 1 (with preheating) Utilize 1.0 mm thread eutectic solder with soldering flux in the core. Either a rosin-based or non-activated flux is r ecommended. 2) The capacitors shall be pre-heated so that the temperature gradient between the devices and the tip of the soldering iron is Delta T < = 120°C or below. 3) The temperature of the solder iron tip should not exceed 270°C. 4) The required amount of solder shall be melted in advance on the soldering tip. 5) After soldering, the capacitors shall be cooled gradually at room ambient temperature. Forced air cooling is not recommended. Process 2 (without preheating) 1) Soldering iron tip shall never directly touch the termination egress or the case body of the capacitors. Lands are sufficiently pre-heated with a soldering iron tip before sliding the soldering iron tip to the terminal electrode of th e capacitor for soldering. Reference Condition Case Size All Temperature of soldering iron 270°C Wattage 20 W maximum Shape of soldering iron 3 mm maximum Soldering time with soldering iron 3 seconds maximum T550 Through-Hole All encased capacitors will pass the resistance to soldering heat test of MIL-STD-202, Method 210, Condition C. This test simulates wave solder of topside board mount product. This demonstration of resistance to solder heat is in accordance with what is believed to be the industry standard. More severe treatment must be considered reflective of an improper s oldering process. The above figure is a recommended solder wave profile for both axial and radial leaded solid tantalum ca pacitors. Additional mounting recommendations (SMD and Through-Hole): In order to increase the board mount integrity of KEMET's Polymer Hermetic Sealed (SMD or TH version) relative to mechanical shock and vibration, KEMET recommends the use of an adhesive between the component and the PCB. This is defined in the Space Application Electronic Hardware Addendum to J-STD-001 (Requirements for Solder Electrical and E lectronic Assemblies.)

14© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Construction T550 Detailed Cross Section Tantalum Wire Solder Ta2O5 Dielectric (First Layer) Carbon (Third Layer) Silver Paint (Fourth Layer) Polymer (Second Layer) Wire Lead (−) (100% Sn/SnPb) Solder SolderWire Lead (+) (100% Sn/SnPb) Anode Tube Hermetic Seal System (Glass Seal and Ring) Brass Can Tantalum Brass Can Hermetic Seal System (Ring) Tantalum Wire Tantalum Pellet (See Detail for Layers) Hermetic Seal System (Glass Seal) Anode Tube Wire Lead (−) (100% Sn/SnPb) Wire Lead (+) (100% Sn/SnPb) Insulation Sleeve T555 Leadframe (− Cathode)

770 Coating

90% Sn 10% Pb Leadframe (+ Anode) 90% Sn 10% Pb Tantalum Wire Molded Epoxy Case Brass Can/ Insulation Sleeve Molded Epoxy Case Hermetic Seal System (Ring) Hermetic Seal System (Glass Seal) Tantalum Pellet Anode Tube

15© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Capacitor Marking T550 KT550 + 100µF 10% 60V + 2010AAAA Polarity Marks Rated Capacitance B Case Series KEMET ID

4 Digit Date Code*, Lot Code

Tolerance, Rated Voltage (VDC) * 1st & 2nd Digit = Year 3rd & 4th Digit = Week T550 - Military Format B Case Identifying Number Polarity Manufacturer Symbol Nominal Capacitance Rated Voltage

4 Digit Date Code*,

• 1st & 2nd Digit = Year 3rd & 4th Digit = Week T555 Polarity Mark Series Cap Tolerance Capacitance Rated Voltage

4 Digit Date Code* / Lot Code

• 1st & 2nd Digit = Year 3rd & 4th Digit = Week

16© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C Storage Tantalum hermetically sealed and SMD capacitors should be stored in normal working environments. While the capacitors themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature – reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40°C and maximum storage humidity not exceed 60% relative humidity. Temperature fluctuations s hould be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulphur bearing compounds. For optimized solderability capacitors stock should be used promptly, preferably within three years of receipt. Packaging Quantities Case Size Bulk 8.5" Reel* Ammo Pack C-Spec Blank 7200 7443 B Through Hole – 20 per tray 500 250 B Surface Mount – 100 per box N/A C Through Hole – 20 per tray 500 250 * For orders greater than 150 pieces, a 12" reel (500 pieces/reel) will be sent. Weight Case Size Average Weight (grams)KEMET EIA B Through Hole T2 3.63 B Surface Mount – 5.54 C Through Hole T2 5.80

17© KEMET Electronics Corporation • One East Broward Boulevard T 2059_T550 • 1/12/2024 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Tantalum Polymer Capacitors – Hermetically Sealed T550 Axial & T555 Surface Mount 105°C KEMET Electronics Corporation Sales Offi ces For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation.