T1100B MORNSUN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100B 2013.07.09-A/2 Page 1 of 3 Passive single channel analog signal Isolation barrier (Iin & Iout) ——T1100B PART NUMBER SYSTEM TXXXXB Package Isolation power output Power supply Output Input Isolation amplifier

FEATURES

  • 2-port isolation (signal input and signal output)
  • High accuracy (0.1% F.S.)
  • High linearity (0.1% F.S.)
  • Isolation voltage(3KVDC/60S)
  • Low temperature drift(35PPM/°C)
  • Industry class(Operation temp.: -25°C to +71°C)
  • High reliability(MTBF>500,000 hours) GENERAL DESCRIPTION Analog signal isolation barrier, is a signal conditioner with electrical insulation between input and output, it can receive a variety of analog signal from the field instrument, and transmit a standard output signal or user-specified special signal to the control room or DCS. The product is isolated between power supply, input and output. It is widely used in the industrial measurement systems, medical electronic equipment, electrical equipment etc. Adopting high efficiency electromagnetism isolation technology to achieve signal isolation, it is available to keep high output accuracy, good linearity and low temperature drift. SELECTION GUIDE Model Power Supply Input Output Isolation Power Output Channels T1100B NONE 4~20mA 4~20mA NONE 1

ELECTRICAL CHARACTERISTICS

Input power NONE Power Supply Power Protection NONE Input Signal 4~20mA Overload ≤50mA Input Voltage Drop-out <3V(@20mA) Output Signal 4~20mA Load ability ≤300Ω(@Output =20mA) Output Load Regulation <0.05% meas.val./100Ω TRANSMISSION CHARACTERISTICS Zero Offset 0.1%F.S. Gain Error 0.1%F.S. Temperature drift coefficient 0.0035%F.S./°C (-25°C to +71°C) ISOLATION CHARACTERISTICS Galvanic Isolation Two-port isolation (signal input and signal output) Isolation Voltage 3kVDC (Tested for 1minute and leakage current < 1mA, humidity < 70%) Insulation Resistance 100MΩ, 500VDC (Between signal input ,signal output, power supply and isolation power output)

The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100B 2013.07.09-A/2 Page 2 of 3 OTHER CHARACTERISTICS Operation temperature:-25°C to +71°C Ambient Temperature Transport and Storage temperature:-40°C to +85°C Package 35mm DIN-rail package Safety Class IP20(IEC60529 / EN60529) EMC compliance GB/T 18268(IEC61326-1) Weight 60g，typ Application Environment No dust, fierce vibration, impulsion and corrosive gas Note: 1 .All specifications measured at TA=25°C, humidity<75%, the value of nominal input and rated output load unless otherwise specified. 2. Only typical models listed, specifications of custom product may be different. Please contact our service people directly for certain conditions. APPLICATION CIRCUIT DIAGRAM & PIN DESCRIPTION Input Output 1(NC) 2(NC) 3(-) 4(+) 5(-) 6(+) 8(NC) 7(NC) OutputInput Iin+ Iin- Iout+ Iout- CONNECTION 1. Cross section area of wiring: 0.5mm -2.5 mm 2. Multi-strand wire, the length of bare wire is about 8mm, fixed by the M4 bolt. APPLICATION NOTE 1. Please read the user manual carefully before using. If any question please contact our FAE. 2. Please do not use this product in hazardous area. AFTER SERVICE 1. Products are carefully inspected and quality controlled during production and before shipment. If they operated abnormally or there was anything wrong, please contact our agent from which you purchased or MORNSUN FAE as soon as possible. 2. MORNSUN warranty our product for 3 years from manufacturing date. During this period, MORNSUN will repair or replace the product if product was found to have manufacturing defect. INSTALLATION & DISASSEMBLY DIN35mm standard rail installation 1.Upside of the instrument card in the rail; 2.Push underside of the instrument into the rail. 1. Use a screwdriver (Width of edge≤6mm), cut in the metal card lock from the underside; 2. Boost up the screwdriver and prize the metal card lock downwards; 3. Pull the instrument out of the rail.

The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100B 2013.07.09-A/2 Page 3 of 3 PACKAGING DIMENSION & PACKAGING DIAGRAM Note: 1. All specifications are measured at Ta=25°C, humidity<75%, the value of nominal input and rated output load unless otherwise specified. 2. In this datasheet, all the test setup and methods are based on our corporate standards. 3. All characteristics are for listed models, and non-standard models may perform differently. Please contact our technical support for more details. 4. Please contact our technical support for any specific requirement. 5. Specifications of this product are subject to changes without prior notice. MORNSUN Science & Technology Co.,Ltd. Tel: 86-20-38601850 Fax:86-20-38601272 E-mail: info@mornsun.cn Http://www.mornsun-power.com