STLA180 Vitec | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

STLA180 SERIES 180W L-Bracket Power Supply for I.T. Equipment – Wide Input Voltage 100 to 240 VAC, 47 to 63Hz – Output Voltage Available From 12,24,48VDC – Internal EMI filter – Active Power Factor Correction – Single Output – Input connector mates with Molex housing 09-50-3031 and Molex 2478 series crimp terminal – Output connector mates with Molex housing 09-50-3081and Molex 2478 series crimp terminal – Size: 3.21"x5"x1.54" – Input Surge Current, Over Voltage and Over Load Protection – Synchronous Rectification – Class I

2 Year Warranty Approvals:

Part Number Output Voltage Max. Output Current Total Regulation Maximum Output Power STLA180-S05 * 12 VDC 14.58 A 5% 175W STLA180-S08 24 VDC 7.50 A 3% 180W STLA180-S11 48 VDC 3.75 A 2% 180W *12V models are required to use DINKLE#DT-2N-B01W-04.

Electrical Characteristics

Parameter Test Conditions Min. Typ. Max. Unit Input Voltage Operating Voltage 100 240 VAC Input Frequency 47 63 Hz Power Factor Correction Io = Full load, Vin = 90-260VAC 0.95 0.97 1.0 Output Power Range Vin=100 to 240VAC 0 180 W Input Current (Low Line) Io=Full load, Vin=115VAC 2.3 A Input Current (High Line) Io=Full load, Vin=230VAC 0.9 A Low Line Inrush Current Io=Full load, 25° C, Cool start, Vin=115VAC 48 54 A High Line Inrush Current Io=Full load, 25° C, Cool start, Vin=230VAC 100 108 A Efficiency Io=Full Load, Vin=230VAC 85 88 90 % Line Regulation Io=Full Load 0.5 1 % Load Regulation Vin=230VAC 3 5 % Over Voltage Protection 112 132 % Over Current Protection 110 150 % Transient Response Io=Full Load to Half Load, Vin=100VAC 4 mS Hold-Up Time Io=Full Load, Vin=110VAC 16 mS Start Up Time Io=Full Load, Vin=100VAC 0.3 1 2 S Ripple & Noise (Peak to Peak) Full Load, Vin=90VAC 0.5 1 % Safety Ground Leakage Current Io=Full Load, Vin=240VAC 0.5 0.75 mA Temperature Coefficient All output -0.04 0.04 %/° C

Parameter Test Conditions Min. Typ. Max. Unit Operating Temperature 0 50 70 °C Storage Temperature -40 85 °C Relative Humidity 5 95 % Operating Temperature at 25°C, Calculated per MIL-HDBK-217F 0.1M Hrs De-rate linearly from 100% load at 50° C to 50% load at 70° C Approvals and Compliance Parameter Test Conditions Min. Unit Dielectric Withstanding Voltage for Primary to secondary Primary to secondary 4242 VDC Dielectric Withstanding Voltage for Primary to Ground Primary to ground 2121 VDC Isolation Resistance Test Voltage=500VDC 50 MΩ EMI requirements for CISPR-22 Vin=220VAC B CLASS EMI requirements for FCC PART-15 Vin=110VAC B CLASS Mechanical PIN CHART PIN MODEL 1 2 3 4 5 6 7 8 STLA180-SXX RTN RTN RTN RTN OUT OUT OUT OUT Note: 1. Dimensions are shown in inches or mm. 2. Weight: 486gs approx. 3. Input connector mates with Molex housing 09-50-3031 and Molex 2478 series crimp terminal 4. Output connector mates with Molex housing 09-50-3081and Molex 2478 series crimp terminal