STC11K SUNTSU | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Ceramic SMD 4 Pad Clipped Sinewave (VC)TCXO 1.6mm x 1.2mm Call: +1-949-783-7300 | Fax: +1-949-783-7301 Specifications are subject to change without notice. www.suntsu.com Suntsu Electronics, Inc. 142 TECHNOLOGY DR., SUITE 150 IRVINE, CA 92618

  • ±0.5ppm (Frequency Stability) Available
  • Clipped Sinewave
  • (VC)TCXO
  • Tape and Reel
  • GPS
  • Mobile Communication Equipment
  • Cellular And Cordless Phones
  • IP Networking Features Applications Frequency Range Storage Temperature Freq. Stability vs. Op Temp. Supply Voltage (VDD) See part numbering guide for options See part numbering guide for options. MHz ppm V +85 3.3 -40 -0.5 1.8 Current (IDD) Pullability (VCTCXO) See part numbering guide for options. mA ppm ±16.0±7.0 +0.5 Operating Temperature See part numbering guide for options.°C +85-30 Frequency Tolerance at +25ºC After 2 times reflowppm -2.0 +2.0 Linearity (VCTCXO) Output Load (Clipped Sinewave) VC Input Impedance (VCTCXO) kΩ//pF ms kΩ +10 5.0 -10 500 Phase Noise (Typical) 100Hz Offset Phase Noise (Typical) 1KHz Offset Phase Noise (Typical) 10KHz Offset -120 -140 dBc/Hz dBc/Hz 10//10 Start-Up Time -155dBc/Hz Output Logic Levels VP-P 0.8 Symmetry (Duty Cycle) Freq. Stability vs. Supply Voltage ±5% changeppm -0.2 +0.2 Freq. Stability vs. Load ±10% changeppm -0.2 +0.2 Freq. Stability vs. Aging 1 Yearppm -1.0 +1.0 Control Voltage (VC, VCTCXO) Center Voltage: VDD*50%.V 0.9* VDD0.1*VDD Phase Noise (Typical) 1Hz Offset -57dBc/Hz Phase Noise (Typical) 10Hz Offset -95dBc/Hz STC 11 K 30 R 48 V E - 26.000M Cage Code: 4GUT4 To customize your parameters contact a Suntsu representative. SUNTSU TCXO 1.6mm x 1.2mm CLIPPED SINEWAVE Part Numbering Guide COMPLIANT FREQUENCY STABILITY FREQUENCY P : ±2.0ppm Q : ±1.5ppm R : ±1.0ppm F : ±0.5ppm 07 : 0°C - +70°C 16 : -10°C - +60°C 17 : -10°C - +70°C 27 : -20°C - +70°C 38 : -30°C - +85°C MHz SUPPLY VOLTAGE 18 : 1.8V±5% 25 : 2.5V±5% 27 : 2.7V±5% 28 : 2.8V±5% 30 : 3.0V±5% 33 : 3.3V±5% PULLABILITY BLANK : TCXO H : ±16.00ppm I : ±7.0ppm TCXO/VCTCXO BLANK : TCXO V : VCTCXO OPERATING TEMPERATURE RANGE TypicalUnitsElectrical Parameters Maximum RemarksMinimum

Ceramic SMD 4 Pad Clipped Sinewave (VC)TCXO 1.6mm x 1.2mm Call: +1-949-783-7300 | Fax: +1-949-783-7301 Specifications are subject to change without notice. www.suntsu.com Suntsu Electronics, Inc. 142 TECHNOLOGY DR., SUITE 150 IRVINE, CA 92618 All dimensions are in millimeters (mm) unless otherwise noted. Drawings are not to scale. 1.20±0.15 1.60±0.15 0.60 Max 0.45 0.30 0.45 0.350.900.35 Outline Drawing and Land Pattern Test Circuit (Clipped Sinewave) Waveform (Clipped Sinewave) Typical Phase Noise 0.65 0.30 0.65 0.550.900.55

Ceramic SMD 4 Pad Clipped Sinewave (VC)TCXO 1.6mm x 1.2mm Call: +1-949-783-7300 | Fax: +1-949-783-7301 Specifications are subject to change without notice. www.suntsu.com Suntsu Electronics, Inc. 142 TECHNOLOGY DR., SUITE 150 IRVINE, CA 92618 178 8.0 4.0 4.0 Ø1.55 0.8 11.5Ø13 2.5 Tp (Time At 260°C. 20-40 Sec) TI (Time Above 217°C. 60-150Sec) Ts (Preheat Time. 60-180Sec) T 25°C to Peak (480Sec Max) Rup (Ramp Up, 3°C/Sec Max) Rdn (Ramp Down, 6°C/Sec Max) Temperature (°C) 260 217 200 150 Time (sec) Reflow Profile & Part Marking Tape And Reel Dimensions All dimensions are in millimeters (mm) unless otherwise noted. Drawings are not to scale. 3,000pcs/Reel Mechanical Shock Vibration MIL-STD-202, Method 213, Condition B MIL-STD-883, Method 2007, Condition A MIL-STD-883, Method 1010, Condition B MIL-STD-883, Method 1014, Condition A Moisture Resistance MIL-STD-883, Method 1004MIL-STD-883, Method 1014, Condition C Resistance to Solvents MIL-STD-202, Method 215MIL-STD-883, Method 2003 Temperature Cycling Fine Leak Test Gross Leak Test Solderability Resistance to Soldering Heat MIL-STD-202, Method 210, Condition KJ-STD-020, MSL 1Moisture Sensitivity Environmental Specifications Mechanical Specifications