STC-MBE132POE OMRON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 68
Technical content
No.19S185-01 1/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide GigE Vision Monochrome / Color CMOS PoE Camera STC-MBE132POE (1.3M / Monochrome) STC-MCE132POE (1.3M / Color) Product Specifications and User’s Guide
No.19S185-01 2/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Table of Contents
No.19S185-01 3/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
No.19S185-01 4/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
No.19S185-01 5/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
No.19S185-01 6/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Precautions for safe use Please read carefully this “Precautions for safe use” before use the camera. Then the camera uses correctly with agreeing with below notes. In this “Precautions for safe use”, notes divides into “Warning” and “Caution” to use the camera safety and prevent to harm and damage. Warning This shows, assumption for possibility of serious accident leading death or serious injury if ignore this note and camera uses incorrectly. Caution This shows, assumption for possibility of bear the damage or physical damage if ignore this note and camera uses incorrectly. About Graphic symbols This symbol shows general prohibition. This symbol shows completion or instruction. [Environment / condition] Warning Do not use flammable or explosiveness atmospheres. This will cause of personal injury or fire. Do not use for “safety for human body” related usage. This camera is designed for use “do not harm human body immediately” if by any chance the camera has malfunction. Caution Use and store under specified environmental conditions (Vibration, shock, temperature, humidity) in the specifications for this camera. This will cause of fire or damage the camera. [Installation and cable wiring] Warning Do not use with out of power voltage range that is specified in the specifications for this camera. This will cause of fire, electrification or malfunction. Do not wrong wiring. This will cause of fire or malfunction.
No.19S185-01 7/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Caution The camera housing and 0 V line of camera inside circuit are isolated. There is a risk of short circuit between camera inside ciurcuit and frame ground through other devices. This will cause of malfunction. It is necessary to wiring and mounting that is specified in the specifications for this camera. This will cause of fire or malfunction. It is necessary to wiring with turn off the camera. This will cause of electrification or malfunction. It is necessary to mounting the camera without stress for the cable. This will case of electrification or fire. [Usage instruction] Warning Do not touch the terminal and PCB board While turn on the camera. This will cause of electrification or accident caused by malfunction. Do not put combustibles near the camera. This will cause of fire. Do not use without usage that is specified in the specifications for this camera. This will cause of personal injury or malfunction. Do not push metals including screw driver into radiation holes. This will cause of electrification or malfunction. Do not touch the camera housing while or afterusing the camera. There is a risk of get burned. Caution Do not push contamination into opening of the camera. This will cause of electrification or malfunction. Do not block the radiation holes. This will cause of fire due to increase the camera inside temperature. [Maintenance] Caution Do not disassemble or repair the camera. This will cause of fire, electrification or malfunction. It is turn off the camera when maintaining or inspecting the camera. This will cause of electrification. [Disposal] Caution It is necessary to dispose as industrial waste.
No.19S185-01 8/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
1 Product Precautions
Do not give shock to the camera. Do not haul or damage the camera cable. Do not wrap the camera with any material while using the camera. This will cause the internal camera temperature to increase. When the camera moving or using the place that temperature difference is extreme, countermeasure for dew condensation (heat removal / cold removal) is necessary. While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting in the sensor or filter and scratching or damaging it. Do not keep the camera under the following conditions. ・ In wet, moist, high humidity or dusty place ・ Under direct sunlight ・ In extreme high or low temperature place ・ Near an object that releases a strong magnetic or electric filed ・ Place with strong vibrations Apply the power that satisfies the specified in specifications for the camera. The defective pixels may appear due to the sensor characteristics. Use below recommend materials (or equivalent materials) to clean the surface of glass. ・ Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.) ・ Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.) ・ Non-woven: nikowipe clean room (NKB) Use a soft cloth to clean the camera.
2 Warranty
■Warranty period One year after delivery (However, the camera had malfunction with camera uses correctly) In below case for a fee even within warranty period. ・The malfunction caused by incorrect usage, incorrect modify or repair. ・The malfunction caused by external shock including the camera dropping after delivery the camera. ・The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or wrong voltage. ■Warranty coverage Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility. “Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the camera malfunction is not included.
No.19S185-01 9/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
3 Software Licensing
3.1 LWIP TCP/IP Licensing
The software in this camera includes LWIP TCP/IP implementation. The copyright information is Copyright (c) 2001-2004 Swedish Institute of Computer Science. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHOR \\AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
No.19S185-01 10/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
4 Introduction
This document describes the specification of the following cameras: STC-MBE132POE / STC-MCE132POE
4.1 Features
GigE Interface Support PoE (Power over Ethernet) Small robust camera housing Maximum frame rate (Full resolution): 61 fps @ 13M 8bits CMOS (Global Shutter) Up to 2,048 Defective Pixel Correction (Default: ON) 8bits, 10bits output
4.2 Naming Method
B: Monochrome C: Color POE: PoE (Power over Ethernet (Gigabit Ethernet)) Sensor Manufacture E: e2V 132: 1/1.8”, 1.3M Sensor
No.19S185-01 11/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
5 Specifications
5.1 Electronic Specifications
Product STC-MBE132POE STC-MCE132POE Image Sensor 1/1.8” 1.3M Progressive Monochrome CMOS (e2V: EV76C560) 1/1.8” 1.3M Progressive Color CMOS (e2V: EV76C560) Shutter Type Global Shutter / Rolling Shutter Active Picture Elements 1,280 (H) x 1,024 (V) Cell Size 5.3 (H) x 5.3 (V) µm Scanning Mode Full scanning (Full resolution) / ROI Frame rate (at full scanning) 8bits: 61.0 fps / 10bits: 41.9 fps / 10bits Packed: 55.9 fps / RGB8: 27.9 fps ADC bit depth 10bits Image Output Format (*1) Mono8 / Mono10 / Mono10Packed Mono8 / Mono10 / Mono10Packed / BayerBG8 / BayerBG10 / BayerBG10Packed / RGB8 Noise Level 8bits output Less than 3 digits (Gain 0 dB) 10bits / 10bits Packed output Less than 12 digits (Gain 0 dB) Sensitivity (*2) 460 Lux 900 Lux Exposure Time 10 µseconds to 1.0300 seconds (Default: 16,379 µseconds) Gain Analog Gain x1 to x2 (Default: x1) Digital Gain x1 to x3 (Default: x1) ROI Horizontal: 8 to 1,280 pixels, Vertical: 2 to 1,024 lines (Default: 1,280 x 1,024) Adjustable steps for size: 8 pixels in horizontal direction and 2 lines in vertical direction Adjustable steps for offset: 8 pixels in horizontal direction and 2 lines in vertical direction Gamma Gamma 0.1 to 4.0 (Default: 1.0) Binning Horizontal x2, x4 and Vertical x2, x4 binning / Off Decimation Horizontal and Vertical binning (2x2) / Off Image Flip Horizontal / Vertical / Horizontal and Vertical / Off Defective Pixel Correction Up to 2,048 points (Default: On) Auto Image Control Auto Exposure Support (Default: OFF) Auto Gain Support (Default: OFF) Auto White Balance N/A Support Operational Mode Edge preset trigger / Free run Interface PoE: IEEE802.3af CLASS2 (1000BASE-T) Protocol GigE Vision 2.1 and GenICam SFNC 2.4, IEEE1588 (PTP) I/O One opto-isolated input, one opto-isolated output and one open collector GPIO (Input or output) Power Input Voltage (*3) +10.8 to +26.4 Vdc External power (via 6 pin connector) / Power Over Ethernet (IEEE802.3af) Consumption +12 V / +24 V: 3.0 W, PoE: 3.1 W Default: Bold
No.19S185-01 12/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Precautions (*1) The Bayer color image format changes when selecting flip image function. Bayer color image format for flip image is off Is listed on this specification. (*2) The sensitivity is measuring the luminance when white level achieved 100 % in below conditions. (*3) The camera operates with external power when power suppling by external power supply and PoE to camera at same time. Camera Setting Environment Parameter Setting Parameter Setting Gain Up 0 dB Light Source Light Box (White) AGC Off Color temperature 5,100K White Balance Optimum Lens Electrical Shutter 1/30 seconds F on Lens F5.6 Black Level Optimum Target Luminance IM-600 (Topcon) Gamma Factory Setting
No.19S185-01 13/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
5.2 Spectral Sensitivity Characteristics
STC-MBE132POE / STC-MCE132POE IR Cut Filter (STC-MCE132POE)
No.19S185-01 14/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
5.3 Mechanical Specifications
Model Number STC-MBE132POE STC-MCE132POE Dimensions 29 (W) x 29 (H) x 53 (D) mm (*1) Optical Filter No Optical Filter IR Cut Filter Optical Center Accuracy Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm Rotational accuracy of Horizontal and Vertical: +/- 1.5 deg. Material Aluminum Alloy (AC) Lens Mount C mount Interface Connectors Ethernet connector: RJ45 connector Power- I/O connector: HR10A-7R-6PB (Hirose) or equivalent Camera Mounting Six M3 screw holes (Two on top, four on bottom plate) Weight Approximately 63 g (*1) Excluding the connectors
5.4 Environmental Specifications
Model Number STC-MBE132POE STC-MCE132POE Operational Temperature / Humidity Minimum Environmental Temperature: 0 deg. C, Environmental Humidity: 0 to 85 %RH (No condensation) Maximum Environmental Temperature: +35 deg. C or Camera housing temperature (top plate) shall not exceed +57 deg. C (*1) Environmental Humidity: 0 to 85 %RH (No condensation) Storage Temperature / Humidity Environmental Temperature: -20 to +75 deg. C, Environmental Humidity: 0 to 85 %RH (No condensation) Vibration 20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10 G, XYZ 3 directions, 30 min. each Shock Acceleration 38 G, half amplitude 6 ms, XYZ 3 directions, 3 times each Standard Compliancy EMS: EN61000-6-2, EMI: EN55011 RoHS RoHS Compliance (*1) Please insure the camera is installed with the appropriate heat dissipation. If camera has a mounted lens and a tripod with an aluminum plate, this could decrease the camera housing temperature for heat dissipation. When the internal temperature sensor on the camera shows less than 65 deg. C, the camera housing temperature (top plate) will be less than 57 deg. C. Taking these steps will maintain the heat rating of the electronic components of the camera. Upper side of camera Measuring point
No.19S185-01 15/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
6 Connector Specifications
6.1 RJ45 Connector
This product is PoE compliant. Please supply power (+10.8 to +26.4 Vdc) through the power-I/O connector when using non-PoE-compliant NIC. Pin Assignment LED Pin No. Signal Name
1 TA+
2 TA-
3 TB+
4 TC+
5 TC-
6 TB-
7 TD+
8 TD-
Please use a 1GB supported NIC, Network Switcher and Ethernet cable. Check the setting of NIC and Network Switcher being used is “1GB transferring”. Green LED Yellow LED Status Green Light ON Yellow Light OFF Power ON (1GB NIC) Green Light OFF Yellow Light OFF Power ON (100MB NIC) Green Light ON Yellow Light Blinking 1 GB Transferring Green Light OFF Yellow Light Blinking 100 MB Transferring Camera is powered-on Green light: ON Yellow light: Blinking
1 GB Transferring
Green light: OFF Yellow light: Blinking
100 MB Transferring
No.19S185-01 16/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
6.2 Power and Control Signal Connector
HR10A-7R-6PB (Hirose) or equivalent This connector is for the power supply and input / output signals. The power from this connector is priority power for camera when power supplies through this connector and PoE at same time. Please use HR10A-7P-6S (Hirose) or equivalent for cable. Pin assignment Configuration of Line2 (Pin No.3) and Line1 (Pin No.4) Output signal can be assign by GenICam command. Pin No. Signal Name IN / OUT Voltage 1 POWER IN IN +10.8 to +26.4 Vdc
2 Opto-isolated in
(Line0) IN Low: Smaller than +1.0 V High: +3.0 to +26.4 V * Potential difference between TRG_in and Opt. Isolated Common
3 Open Collector
(Line2) IN / OUT +3.0 to +26.4 V / Open Collector
4 Opto-isolated out
(Line1) OUT Open Collector
5 Opto-isolated
6 GND IN 0 V
1) Frame Trigger Wait (Default for all output) 2) Frame Trigger Internal 3) Exposure Active 4) Acquisition Trigger Wait 5) Acquisition Trigger Internal 6) Sensor Read Out 7) Debounced Line 0 8) Debounced Line 2 9) User Output 1 10) User Output 2 11) Timer 0 Active 12) Software Signal 0 13) Software Signal 1 14) Logic Block 0 15) Pulse Per Second
No.19S185-01 17/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide 1) Frame Trigger Wait The condition of camera operation with trigger signal can be check. “LOW” state of signal is out between “start exposing” to “image out”. 2) Frame Trigger Internal The input trigger signal with the trigger delay (camera internal process delay). 3) Exposure Active While camera exposing, “HIGH” state of signal is out. The signal state will be “LOW” after finish exposing. 4) Acquisition Trigger Wait While image transferring from camera to PC, “Low” state of signal is out. The signal state will be “High” after finish image transferring. 5) Acquisition Trigger Internal The image transferring starts signal is out. 6) Sensor Read Out FVAL (Frame valid, HIGH state) signal is out. 7) Debounced Line0 Debounced Line0 signal is out. 8) Debounced Line2 Debounced Line2 signal is out. 9) User Output 1 (User Output signal through Line 1) Selected “HIGH” or “LOW” state of signal is out. 10) User Output 2 (User Output signal through Line 2) Selected “HIGH” or “LOW” state of signal is out. 11) Timer 0 Active Selected signal at “Timer Counter” is out. When signal synchronizing with “Exposure Active” signal, signal can use for strobe control. 12) Software Signal 0 Selected signal for “Software Signal 0” at “Software Signal Control” is out. 13) Software Signal 1 Selected signal for “Software Signal 1” at “Software Signal Control” is out. 14) Logic Block 0 “Logic Block 0” signal is out. 15) Pulse Per Second “Pulse / second” signal (50% Duty, 1 Hz interval) is out.
No.19S185-01 18/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Opto-isolated input The camera has current limiting circuit on camera. The current limiting resistor does not necessary. Opto-isolated output It is necessary to have current limiting resistor at outside of camera, to keep less than 50 mA.
No.19S185-01 19/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Open Collector GPIO This GPIO can be used for input or output. When using as output, it is necessary to have current limiting resistor at outside of camera, to keep current less than 50 mA. When using as input, current limiting resistor does not necessary. However, camera does not have current limiting circuit on camera. The camera inside circuit may get damage if accidentally uses as output without current limiting resistor. For safety, please add current limiting resistor even use as input. a) Open Collector GPIO uses as output b) Open Collector GIPO uses as input
No.19S185-01 20/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Input and Output Signal Timing (Hardware Trigger) Case of “External Hardware Trigger”, “Timed Exposure Mode” and “Positive Edge Trigger” External hardwareTrigger signalTrigger delayExposureImage outCamera internal processing Output signalsFrameTriggerWaitExposureActiveDebounceLine0, 2FramTriggerInternalSensorReadOutTimer0 DebounceExternal hardwareTrigger delayTdelay (*1)Parameter “ExposureTime” on GenICamParameter “LineDebounceTime” on GenICamParameter “TriggerDelay” on GenICam Parameter “TimerDelay” on GenICam Parameter “TimerDuration” on GenICam (*1) Please refers “5.2.6 External Hardware Trigger Input Delay” for more details about “External hardware trigger delay”
No.19S185-01 21/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Input and Output Signal Timing (Software Trigger) Case of “Software Trigger”, “Timed Exposure Mode” and “Positive Edge Trigger” Software triggerTrigger delayExposureImage outCamera internal processingOutput signalsFrameTriggerWaitExposureActiveFramTriggerInternalSensorReadOutTimer0Parameter “ExposureTime” on GenICamParameter “TriggerDelay” on GenICam Parameter “TimerDelay” on GenICamParameter “TimerDuration” on GenICam
No.19S185-01 22/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide External Hardware Trigger Input Delay The input trigger signal has some delay inside camera by photo coupler or transistor. Please refers example measurement of delay in below.
6.2.6.1 External Trigger Signal Delay (Positive polarity trigger signal)
External Trigger SignalExternal Trigger Signal with camera internal delayTdelay
6.2.6.2 External Trigger Signal Delay (Negative polarity trigger signal)
External Trigger SignalExternal Trigger Signal with camera internal delayTdelay
No.19S185-01 23/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
6.2.6.3 Measured External Trigger Signal Delay through Opt-Isolated Port (Line 0)
Positive polarity trigger signal Negative polarity trigger signal Pull-up voltage Tdelay Minimum active pulse duration Pull-up voltage Tdelay Minimum active pulse duration +3.3 V 8.2 μseconds 6 μseconds +3.3 V 47 μseconds 6 μseconds +12 V 4.6 μseconds 3 μseconds +12 V 53.2 μseconds 3 μseconds +24 V 4.4 μseconds 2 μseconds +24 V 53.2 μseconds 2 μseconds Note. Please use this measured delay as reference. The delay time may fluctuate depending on photo coupler variation, pull-up voltage and pull-up resister.
No.19S185-01 24/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
6.2.6.4 Measured External Trigger Signal Delay through Open Collector GPIO Port (Line 2)
Positive polarity trigger signal Negative polarity trigger signal Pull-up voltage Tdelay Minimum active pulse duration Pull-up voltage Tdelay Minimum active pulse duration +3.3 V 3.9 μseconds 6 μseconds +3.3 V 0.6 μseconds 6 μseconds +12 V 3.8 μseconds 3 μseconds +12 V 0.8 μseconds 3 μseconds +24 V 2.2 μseconds 2 μseconds +24 V 0.8 μseconds 2 μseconds Note. Please use this measured delay as reference. The delay time may fluctuate depending on transistor variation, pull-up voltage and pull-up resister.
No.19S185-01 25/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
7 Dimensions
7.1 STC-MBE132POE
Unit: mm 2-M3 Depth3.5 φ28.5 2016 7.5 7 1”-32UNF (C mount) 4-M3 Depth3.5 2-M2 Depth4
No.19S185-01 26/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
7.2 STC-MCE132POE
Unit: mm 15202-M3 Depth3.529291”-32UNF (C mount) φ28.55342491520164-M3 Depth3.51202-M2 Depth47.5 7
No.19S185-01 27/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
8 Sensor Information
8.1 Pixel Transferring Image
STC-MBE132POE (Monochrome) Pixel (n) of Data: nth pixel being transferred STC-MCE132POE (Color) Pixel 11 of DataPixel 12 of DataPixel 21 of DataPixel 22 of Data Pixel (m, n) of Data: mth pixel of nth line being transferred Pixel1 of Data Pixel2 of Data
No.19S185-01 28/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
9 Camera Operational Modes
9.1 Normal Mode
ExposeImage outExposure Time * The exposure time for each line is same.
No.19S185-01 29/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
9.2 Edge Preset Trigger Mode
In this trigger mode with positive polarity, the expose starts at rising edge of trigger signal. The exposure duration time is based on preset exposure setting stored by camera setting communication. In this trigger mode with negative polarity, the expose starts at falling edge of trigger signal. The exposure duration time is based on preset exposure setting stored by camera setting communication. The input trigger signal is disregard when trigger signal applying to camera while camera is exposing or sending out image data. Timing ExposeImage outTrigger signal(Positive polarity) Note: The exposure time is “Exposure Time” on GenICam setting.
No.19S185-01 30/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Exposure Timing with Positive Polarity Trigger Signal Exposure TimeTrigger signal(Positive polarity)Trigger signal withcamera internal delayTdelay*Note 2Debounce*Note 1T1'Exposure Time: T1' = Preset Exposure Time Setting Note 1: The trigger signal will be removed by filtering if active pulse width of input trigger signal is less than “Line Debounce Time” setting time. Please input trigger signal has more than “Line Debounce Time” time active pulse width trigger signal. Note 2: Please refers “5.2.6 External Hardware Trigger Input Delay” for more details about “External hardware trigger delay”.
No.19S185-01 31/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Exposure Timing with the Negative Polarity Trigger signal Exposure TimeTrigger signal(Negative polarity)Trigger signal withcamera internal delayTdelay*Note 2Debounce*Note 1T1'Exposure Time: T1' = Preset Exposure Time Setting Note 1: The trigger signal will be removed by filtering if active pulse width of input trigger signal is less than “Line Debounce Time” setting time. Please input trigger signal has more than “Line Debounce Time” time active pulse width trigger signal. Note 2: Please refers “5.2.6 External Hardware Trigger Input Delay” for more details about “External hardware trigger delay”.
No.19S185-01 32/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
9.3 CMOS Rest Type
With this camera, you can select the sensor exposure type as either "Electronic Rolling Shutter (ERS)" or "Global Reset (GR)". Electronic Rolling Shutter(ERS) Global Shutter (for EdgePreset) Note: This function works on Trigger-mode Trigger Input Exposurein Rolling Shutter mode(in Camera)1st ROW2nd ROWLast ROWData Tx(Camera to PC) ・・・ Exposure Time Exposure Start Delay internaldelay Trigger Input Exposurein Global Shutter(in Camera)1st ROW2nd ROWLast ROWData Tx(Camera to PC) Exposure Time Exposure Start Delay・・・
No.19S185-01 33/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10 Camera Functions
10.1 Save and load the camera settings
The camera has the camera setting save function, and camera setting including factory default loads function. The camera has below two type of camera settings. Default: The factory default settings (This setting cannot change) User Set X: Over writeable camera settings (X: 0 to 7) These camera settings load from ROM to register in RAM on camera, and camera settings at register in RAM on camera save to ROM. The camera settings saving and loading are controllable with Parameters (“User Set Selector”, “User Set Default Selector”), and commands (“User Set Load”, “User Set Save”) in “User Set Control” category of GenICam. The details of the parameters and the functions are in the table below: GenICam Parameters UserSetSelector IEnumeration Type Select “Default” or ”User Set X” “User Set Load” or “User Set Save” process for selected settings. UserSetLoad ICommand Type The camera settings load from ROM to register in RAM. UserSetSave ICommand Type The camera settings at register in RAM save to ROM. UserSetDefaultSelector IEnumeration Type Select which settings (“Default” or “User Set X”) load automatically when camera power is on. This selection saves automatically. Saving Camera Settings Setting Procedure 1. Selects “User Set X” at “User Set Selector” 2. Execute “User Set Save” When executing “User Set Save”, camera settings at the register in RAM are saved to the ROM that is selected at “User Set Selector”. Caution: “User Set Save” CANNOT execute when “Default” was selected at “User Set Selector” ROM User Set 0 to 7 ROM Default Camera Settings User Set Selector Selector
No.19S185-01 34/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Loading Camera Settings Setting Procedure 1. Select “User Set X” (or Default) at “User Set Selector” 2. Execute “User Set Load” Loading Camera Settings when Camera Power is on Setting Procedure 1. Set “User Set X” or “Default” at “User Set Default” Camera Settings Initialization Please follow the procedure in below for camera settings put back to factory default settings. Setting Procedure 1. Selects “Default” at “User Set Selector”. 2. Executes “User Set Load”. 3. Select “User Set X” at “User Set Selector”. 4. Executes “User Set Save”. When executing “User Set Load”, camera settings load from selected ROM that was selected at “User Set Selector” to register at RAM. When the camera power is on, camera settings load from selected ROM that was selected at “User Set Default” to register at RAM. ROM User Set 0 to 7 ROM Default Camera Settings User Set Selector Selector ROM User Set 0 to 7 ROM Default Camera Settings User Set Selector Selector
No.19S185-01 35/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.2 Frame rate
This parameter sets the frame rare (fps) of output image from camera. GenICam Parameters AcquisitionFrameRate IFloat Type Sets frame rate in Hz unit (*1) Range is changed with exposure time setting Default: 61.0531 (*1) The approximate value of set value, sets to camera and display it.
10.3 Gain
The gain has Analog Gain, Digital Gain. Analog Gain This parameter sets analog gain. Selects “Analog ALL” at “Gain Selector”, sets gain at “Gain”. GenICam Parameters GainSelector IEnumeration Type Selects control gain Analog All: Analog Gain Gain IFloat Type Analog Gain Range: 0 to 2 Default: 0 Analog Gain Formula Gain (dB) = 1 + (“Gain” / 2) Digital Gain This parameter sets digital gain. Selects “Digital ALL” at “Gain Selector”, sets gain at “Gain”. GenICam Parameters GainSelector IEnumeration Type Selects control gain Digital All: Digital Gain DigitalGain IFloat Type Digital Gain Range: 0 to 255 Default: 0 Digital Gain Formula Gain (x times) = 1 + (“Digital Gain” / 128)
No.19S185-01 36/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.4 Exposure Time
This parameter sets variable exposure time. The control method is selectable from Manual exposure control, which uses preset exposure time. Auto exposure control, which is maintain exposure time with brightness of target. GenICam Parameters ExposureMode IEnumeration Type Exposure control selection Selection: “Off” and “Timed” Off: Exposure time is “1 / Frame rate” Timed: Exposure time is “Exposure Time” ExposureTime [ExposureTime Selector] IFloat Type Exposure time (in μsecond) (*1) Range: 1.000000 to 1,030,066.070000 Default: 16,379.198000 ExposureAuto IEnumeration Type Auto exposure ON / OFF selection (*2) (*1) The approximate value of set value, sets to camera and display it. (*2) Please sets range of auto exposure control with “Exposure Auto Limit Min” and “Exposure Auto Limit Max” when using auto exposure control.
10.5 Black Level
This parameter sets the black level (clamp level for black signal). Sets the black level at “Black Level”. The lower limit of signal is clamped at this setting level. The signal does not lower than this. GenICam Parameters BlackLevel IFloat Type Black Level Range: 10bits output: 0 to 60 8bits output: 0 to 15 Default: 0
No.19S185-01 37/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.6 ALC (Auto Light Control)
ALC function has two control methods, which is AGC (Auto Gain Control) and auto shutter. The AGC and auto shutter can be set individually. The camera parameters are adjusted to brightness of image is maintained with target brightness automatically with ALC function. AGC or auto shutter have to set “On” to activate ALC function. GenICam Parameters (for AGC and auto shutter) AutoLuminanceTarget IInteger Type Target brightness Range: 0 to 255 Default: 128 AutoLuminanceRegion Selector IEnumeration Type ALC weight region to set area, position and weight Selection: Region 0 to Region 8 AutoLuminanceWidth IInteger Type Width for selected ALC weight region Range: 4 to 1,248 Default: 405 for all regions AutoLuminanceHeight IInteger Type Height for selected ALC weight region Range: 2 to 988 Default: 317 for all regions AutoLuminance OffsetX IInteger Type Horizontal offset for selected ALC weight region Range: 0 to 875 Default: 32 (Region 0, 3 and 6), 437 (Region 1, 4 and 7), 842 (Region 2, 5 and 8) AutoLuminance OffsetY IInteger Type Vertical offset for selected ALC weight region Range: 0 to 707 Default: 36 (Region 0 to 2), 353 (Region 3 to 5), 670 (Region 6 to 8) AutoLuminanceWeight IInteger Type Weight Range: 0 to 15 Default: 1 * Sets 10 on Region 4 only Sets the weight for each weight area. AutoLuminancePeak IInteger Type Importance ratio for the brightness peak at ALC control. Range: 0 to 255 Default: 0
No.19S185-01 38/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Target Brightness Formula (Auto Luminance Target) 10bits output: Target Brightness (Gradient) = “Auto Luminance Target” × 4 8bits output: Target Brightness (Gradient) = “Auto Luminance Target” About the importance ratio for brightness peak at ALC control (Auto Luminance Peak) When setting 0, Average: 100 %, Peak: 0 %. The ALC control with brightness average. When setting 255, Average: 0 %, Peak: 100 %. The ALC control with brightness peak. When setting 128, Average: 50 %, Peak: 50 %. ALC control method The ALC control with weight region 0 to 8. The weight area setting parameters are in below: The brightness average and peak calculate for each weight area. The target brightness comparison value calculates with “Auto Luminance Peak”, the brightness average and peak then compare with target brightness to define necessary brightness control (to dark or to bright). The brightness of image maintains to “Auto Luminance Target” with AGC and auto shutter functions. If AGC and auto shutter are ON for ALC control, auto shutter function maintains brightness first. The AGC function maintains brightness if brightness cannot maintain to “Auto Luminance Target” with auto shutter. OffsetY Height Width OffsetX Region0 Region1 Region2 Region3 Region4 Region5 Region6 Region7 Region8
No.19S185-01 39/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide AGC (Auto Gain Contorl) The brightness of image maintains to keep target brightness with gain automatically. If the brightness of image is darker than target brightness, gain increases up to “Gain Auto Limit Max”. If the brightness of image is brighter than target brightness, gain decreases. GenICam Parameters GainSelector IEnumeration Type Adjustable gain selection Selected gain can be adjusting by Gain[GainSelector]. Please select “Analog All” when AGC is turned on. Selection: “Analog All” (analog gain) and “Digital All” (digital gain) Default: “Analog All” Gain[GainSelector] IFloat Type Gain Selected gain at “Gain Selector” is adjusting Analog gain: Range: 0 to 2 Default: 0 Digital gain: Range: 0 to 255 Default: 0 Analog gain cannot adjustable when AGC is turned on. GainAuto [GainSelector] IEnumeration Type AGC ON / OFF selection Selection: “ON” (Continuous) and “OFF” (Off) Default: OFF GainAutoLimitMin [GainSelector] IFloat Type Minimum gain for AGC Range: 0 to 208 Default: 0 This cannot be set greater than “Gain Auto Limit Max” GainAutoLimitMax [GainSelector] IFloat Type Maximum gain for AGC Range: 0 to 208 Default: 208 This cannot be set smaller than “Gain Auto Limit Min”
No.19S185-01 40/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Auto shutter The brightness of image maintains to keep target brightness with shutter automatically. If the brightness of image is darker than target brightness, exposure time extends up to “Exposure Auto Limit Max”. If the brightness of image is brighter than target brightness, exposure time becomes shorter up to “Exposure Auto Limit Min”. GenICam Parameters ExposureAuto IEnumeration Type Auto shutter ON / OFF selection Selection: “ON” (Continuous), “OFF” (Off) Default: “OFF” ExposureAutoLimitMin IFloat Type Minimum exposure time (in µsecond) for auto shutter Range: 10 to 1,030,066.070000 Default: 10.000000 ExposureAutoLimitMax IFloat Type Maximum exposure time (in µsecond) for auto shutter Range: 10 to 1,030,066.070000 Default: 16,379.198000 ALC settings procedure ALC Settings Procedure 1. Sets “Auto Luminance Width”, “Auto Luminance Height”, “Auto Luminance Offset X”, “Auto Luminance Offset Y” and “Auto Luminance Weight” for “Auto Luminance Region 0 to 8”. 2. Sets “Continuous” for “Gain Auto” when using AGC function. 3. Sets “Gain Auto Limit Min” and “Gain Auto Limit Max” when using AGC function. 4. Sets “Continuous” for “Exposure Auto” when using auto shutter function. 5. Sets “Exposure Auto Limit Min” and “Exposure Auto Limit Max” when using auto shutter function. 6. Sets “Auto Luminance Target”.
No.19S185-01 41/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.7 White balance (Only available for color camera)
The color compensates with gain adjustment each color. The gain for each color has to adjust each color has same brightness when taking flat white target. The white balance control methods are listed in below: OFF Auto white balance Push to set white balance Preset 0 to 2 White balance control methods GenICam Parameters BalanceRatioSelector IEnumeration Type White balance control target color selection Selection: “Red”, “Green” and “Blue” BalanceRatio IFloat Type Color gain setting for color selects at “Balance Ratio Selector” Range: 0 to 255 BalanceWhiteAuto IEnumeration Type White balance control method selection. Selection: “Off”, “Once”, “Continuous”, “Preset 0”, “Preset 1” and “Preset 2” Default: “Off” White balance control method selection OFF The white balance with “Balance Ratio” setting for Red, Green and Blue. If the white balance process is not necessary, please sets 0 for “Balance Ratio” for all colors. White balance “OFF” setting procedure 1. Sets “Off” at “Balance White Auto”. Auto white balance The optimized white balance gain calculates each frame for auto white balance. Auto white balance setting procedure 1. Sets “Continuous” at “Balance White Auto”. Push to set white balance The white balance gain adjusts once after select this white balance then set to “Balance Ratio” for all colors. Sets “OFF” at “Balance White Auto” automatically after sets “Balance Ratio” for all colors. Push to set white balance setting procedure 1. Sets the flat white target then acquires image. 2. Sets “Once” at “Balance White Auto”.
No.19S185-01 42/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Preset white balance 0 to 2 The camera has three preset manual white balances. Preset white balance setting procedure 1. Selects “Preset 0” to “Preset 2” at “Balance White Auto”. 2. Selects adjusting color from Red, Green or Blue at “Balance Ratio Selector”. 3. Sets gain for selected adjusting color at “Balance Ratio”. The settings can be save into camera with “User Set Control” function.
No.19S185-01 43/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide White balance calculate region setting The size and position for white balance gain calculation region are changeable. GenICam Parameters BalanceWhiteAuto RegionSelector IEnumeration Type White balance gain calculation region selection Selection: Region 0 BalanceWhiteAuto Width IInteger Type Width (horizontal size, in pixel) for white balance gain calculation region Range: 1 to 1,280 Default: 1,280 BalanceWhiteAuto Height IInteger Type Height (vertical size, in line) for white balance gain calculation region Range: 1 to 1,024 Default: 1,024 BalanceWhiteAuto XOffset IInteger Type Horizontal offset (in pixel) for region 0 Range: 0 to 1,279 Default: 0 BalanceWhiteAuto YOffset IInteger Type Vertical offset (in line) for region 0 Range: 0 to 1,023 Default: 0 The white balance calculation region settings are like below: BalanceWhite AutoOffsetY BalanceWhite AutoHeight BalanceWhite AutoWidth BalanceWhite AutoOffsetX White balance gain calculation region 0
No.19S185-01 44/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.8 Gamma correction
The gamma correction is changeable. GenICam Parameters Gamma IFloat Type Gamma correction Range: 0 to 4.0 Default: 1.0
10.9 ROI (Region of Interest)
The specified region of image can be output from camera with ROI function. GenICam Paramters Width IInteger Type Width (horizontal size) of output image (in pixel) Range: 8 to 1,280 Default: 1,280 Adjustable steps: 8 (“Width” + “Offset X”) should not exceeded maximum width. Height IInteger Type Height (vertical size) of output image (in line) Range: 2 to 1,024 Default: 1,024 Adjustable steps: 2 (“Height” + “Offset Y”) should not exceeded maximum height. OffsetX IInteger Type Horizontal offset for output image (in pixel) Range: 0 to 1,272 Default: 0 Adjustable steps: 8 OffsetY IInteger Type Vertical offset for output image (in line) Range: 0 to 1,022 Default: 0 Adjustable steps: 2 The ROI region settings are below: Width Height OffsetX OffsetY ROI region
No.19S185-01 45/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.10 Pixel Format
The image format from camera can be set on Pixel Format. GenICam Parameters PixelFormat IEnumeration Type Pixel Format The following chart shows the available Pixel Formats on camera: Output Bits Pixel Format Monochrome Camera STC-MBE132POE Color Camera STC-MCE132POE 8bits Mono8 Mono8 BayerRG8 10bits Mono10 Mono10 BayerRG10 10bits Packed Mono10Packed Mono10Packed BayerRG10Packed 8bits x 3 N/A RGB8 Each format specified on GenICam PFNC (Pixel Format Naming Convention).
10.11 Binning
Binning is add or average beside pixels into one pixel. The sensitivity is increased when adding pixel data. The noise is reduced when averaging pixel data. The pixel data inside of red square add or average as one pixel. STC-MBE132POE STC-MCE132POE Binning X (OFF), Y (OFF)Binning X (ON), Y (ON)Binning X (OFF), Y (OFF)Binning X (ON), Y (ON) GenICam Parameters BinningHorizontal Mode IEnumeration Type Selects Binning mode for horizontal binning function. Selection: Sum, Average (Default) BinningVertical Mode IEnumeration Type Selects Binning mode for vertical binning function. Selection: Sum, Average (Default) BinningHorizontal IInteger Type Sets Binning on Horizontal direction 1: Disable Binning (Default) 2: Binning 2 Pixel BinningVertical IInteger Type Sets Binning on Vertical direction 1: Disable Binning (Default) 2: Binning 2 Pixel *Note Horizontal Binning and vertical Binning settings need to change together.
No.19S185-01 46/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.12 Decimation
When using Decimation mode, the decimated image can be output. The frame rate increases with vertical decimation (the frame rate does not increase with horizontal decimation) The images below show decimated pixels (red squares) where they are output. STC-MBE132POE Decimation X (OFF), Y (OFF)Decimation X (OFF), Y (ON)Decimation X (ON), Y (OFF)Decimation X (ON), Y (ON) STC-MCE132POE Decimation X (OFF), Y (OFF)Decimation X (OFF), Y (ON)Decimation X (ON), Y (OFF)Decimation X (ON), Y (ON) GenICam Parameters DecimationHorizontal IInteger Type Sets decimation on horizontal direction 1: Disable Decimation (Default), 2: Decimate one of two pixels 4: Decimate three of four pixels DecimationVertical IInteger Type Sets decimation on vertical direction 1: Disable Decimation (Default), 2: Decimate one of two pixels 4: Decimate three of four pixels *Note: Please check and change exposure time to increase frame rate by decimation function.
No.19S185-01 47/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.13 Trigger
The trigger type (trigger source) is selectable at “Trigger Source” under “Acquisition Control”. The trigger type (trigger source) is listed in below table. Software Software trigger generates by “Trigger Software” Software Signal 0 Software trigger generates by “Software Signal Control” Software Signal 1 Software trigger generates by “Software Signal Control” Action 0 Action command trigger Line 0 Hardware trigger through “Line 0” Line 2 Hardware trigger through “Line 2” Logic Block 0 Trigger generates by “Logic Block Control” Please refers “Trigger signal processing procedure” for more details Trigger signal processing procedure The camera internal process for external hardware trigger signal or software trigger signal input is below: Line 0Line 2DebounceDebounce “AND”or“OR” Line 2Action 0Line 0SoftwareSoftware Signal 0Software Signal 1Logic Block 0Trigger SourceTrigger DelayCameraTimingGeneratorSensor The trigger signal is selectable by GenICam commands. Trigger Source: select trigger type
No.19S185-01 48/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.14 Image Flip
The horizontal flip image can be selected by “Reverse X”. The vertical flip image can be selected by “Reverse Y”. GenICam Parameters ReverseX IBoolean Type Horizontal flip image ON / OFF selection Selection: “False” (Horizontal flip is Off), “True” (Horizontal flip is On) Default: “False” (Horizontal flip is Off) ReverseY IBoolean Type Vertical flip image ON / OFF selection Selection: “False” (Vertical flip is Off), “True” (Vertical flip is On) Default: “False” (Vertical flip is Off)
10.15 LUT Control
The output signal assigned table for input signal. GenICam Parameters LUT Selector IEnumeration Type Control LUT selection (Luminance is only selectable) Default: Luminance LUT Enabled IBoolean Type LUT ON / OFF selection LUT Index IInteger Type Index for LUT Range: 0 to 4,095 LUT Value IInteger Type The output value for input value that specifies by index Range: 0 to 4,095 LUT Index0 4095LUT Value4095 e.g. LUT usage (low brightness level enhancement)
No.19S185-01 49/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.16 Defective pixel correction
The selected position of defective pixel is correcting with adjacent pixel information. The selected position of defective pixel of color camera is correcting with adjacent same color of pixel information. GenICam Parameters PixelCorrectionAll IBoolean Type Defective pixel correction ON / OFF selection Selection: “True” (On), “False” (Off) Default: “True” PixelCorrection Enabled IBoolean Type Defective pixel correction ON / OFF selection for selected index Selection: “True” (On), “False” (Off) Default: “False” (Off) PixelCorrection Index IInteger Type Index for process defective pixel correction Range: 0 to 2,047 Default: 0 PixelCorrectionX IInteger Type Horizontal position for selected index for process defective pixel correction Range: 0 to 1,279 Default: 0 PixelCorrectionY IInteger Type Vertical position for selected index for process defective pixel correction Range: 0 to 1,023 Default: 0
No.19S185-01 50/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.17 Counter And Timer Control
Controls “Timer” and “Counter”. A) Timer Control GenICam Parameters TimerSelector IEnumeration Type Fixed as “Timer 0” TimerDelay IFloat Type Delay for “Timer 0 active” signal (in µsecond) Range: 0 to 16,777,215 Default: 0 TimerDuration IFloat Type Duration of “Timer 0 active” signal (in µsecond) Range: 1 to 16,777,215 Default: 1 TimerTrigger Source IEnumeration Type Reference signal selection to generate “Timer 0 active” signal Default: “Off” TimerTrigger Activation IEnumeration Type Polarity of reference signal to generate “Timer 0 active” signal Default: “Rising Edge” TimerValue IFloat Type Returns value for “Timer 0 active” signal When the timing of “Timer 0 active” signal is adjusting to active signal of Exposure, “Timer 0” can be used as strobe control signal. B) Counter Control GenICam Parameters CounterSelector IEnumeration Type Counter selection Default: “Counter 0” CounterEvent Source IEnumeration Type Counter event source selection CounterReset Source IEnumeration Type Reference signal selection to reset counter CounterReset Activation IEnumeration Type Polarity of reference signal to reset counter CounterReset ICommand Type Rest switch “Activate as switch when selecting “Software” at “Counter Reset Source” CounterValue IInteger Type Returns number of counter
No.19S185-01 51/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.18 Event Control
The camera internal signal can be output as specified event information, like “exposure end”, to PC used by GVCP (GigE Vision Control Protocol). e.g. Event control Notified “Exposure End” Exposure ActiveSensor Read OutEvent Exposure StartEvent Frame StartEvent Exposure EndEvent Frame EndGVCP GenICam Parameters Event Selector IEnumeration Type Event notification selection Selection: “Action Late”, “Frame Trigger”, “Exposure Start”, “Exposure End”, “Frame Start”, “Frame End”, “Block Discard”, “Line 0 Input Rising Edge”, “Line 0 Input Falling Edge”, “Line 2 Input Rising Edge” and “Line 2 Input Falling Edge” Event Notification IEnumeration Type Event notification ON / OFF selection On: Enable event notification Off: Disable event notification
No.19S185-01 52/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.19 Chunk Control
This function is attached additional image information to image data. For example, the exposure time and gain information do not include in image data itself. However, Chunk data transfers these parameters when image was acquiring. GenICam Parameters ChunkModeActive IBoolean Type Chunk control ON / OFF selection Default: “False” (Off) ChunkSelector IEnumeration Type Transfer Chunk data selection Selection: “Image”, “Gain”, “Exposure Time”, “Black Level”, “Line Status All”, “Device Temperature”, “Timer Value” and “Counter Value” ChunkEnable IBoolean Type Enable Chunk data that was selected at “Chunk Selector” Selection: “True” (Enable Chunk data) and “False” (Disable Chunk data)
10.20 Action Control
The multiple cameras control by one action signal. GenICam Parameters ActionQueueSize IInteger Type Size of scheduled action command queue ActionDeviceKey IInteger Type Control identifier of camera ActionSelector IInteger Type Action command application selection Fixed as “0” ActionGroupKey IInteger Type Action command applies camera * The camera executes action command when group key of action command and group key of camera is matched. ActionGroupMask IInteger Type Select camera to apply action command Logical AND of Group Mask of camera and Group Mask of action command is 1 for any bit of 32bits, camera executes action command.
No.19S185-01 53/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
10.21 IEEE1588
Precision Time Protocol (PTP) is implemented on camera, is synchronized to “Master Clock” in same network automatically. The camera supports IEEE 1588-2008 of PTP Version 2. The accuracy of time (Timestamp) synchronized is different based on network system configuration. 1) BMC (Best Master Clock) function BMC function is implemented on camera. The most accurate clock in same network is defined as “Master Clock” then time (Timestamp) synchronizes. If there are more than two devices has most accurate clock in same network, clock of smallest MAC address device is defined as “Master Clock”. 2) E2E (End-to-End) Transparent Clock The camera supports E2E method. Time difference is correcting by blow algorithm MasterSync messageSlaveFlow up messageTimestampTimestampTimestampDelay request messageTimestamp “Delay request” reply messageSwitching HUBTime The master device and slave device exchange message included Timestamp. Defined delay between master device and slave device by comparing these messages. If time difference between master device and slave device is occurred, adjust internal clock of slave device to synchronize to master device. Synchronize clock regularly to correcting time drift.
No.19S185-01 54/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide 3) How to use PTP Selects “True” at GevIEEE1588 then synchronize camera time to “Master Clock” (synchronize time is different depending on system). The camera is ready for action command after synchronize to “Master Clock”. 4) Synchronized exposure for trigger mode When action command generating, action command is broadcasting to each camera and camera starts exposing. Synchronized exposure does not secure if action command does NOT include Timestamp. If action command includes Timestamp, action command will be scheduled automatically and each camera start exposing at same time. Action Control setting is required when action command generating. IEEE1588PTP supported Switching HUBPCMS SSSSM: MasterS: Slave S e.g. PTP configuration
No.19S185-01 55/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11 GenICam command
11.1 DeviceControl
DeviceType Returns the device type. DeviceScanType Scan type of the sensor of the device. DeviceVendorName Name of the manufacturer of the device. DeviceModelName Model of the device. DeviceFamilyName Identifier of the product family of the device. DeviceManufacturerInfo Manufacturer information about the device. DeviceVersion Version of the device. DeviceHardwareVersion Version of the hardware in the device. DeviceFirmwareVersion Version of the firmware in the device. DeviceSerialNumber Device's serial number. DeviceUserID User-programmable device identifier. DeviceSFNCVersionMajor Major version of the Standard Features Naming Convention that was used to create the device's GenICam XML. DeviceSFNCVersionMinor Minor version of the Standard Features Naming Convention that was used to create the device's GenICam XML. DeviceSFNCVersionSubMinor Sub minor version of Standard Features Naming Convention that was used to create the device's GenICam XML. DeviceManifestEntrySelector Selects the manifest entry to reference. DeviceManifestXMLMajorVersion Indicates the major version number of the GenICam XML file of the selected manifest entry. DeviceManifestXMLMinorVersion Indicates the minor version number of the GenICam XML file of the selected manifest entry. DeviceManifestXMLSubMinorVersion Indicates the sub minor version number of the GenICam XML file of the selected manifest entry. DeviceManifestSchemaMajorVersion Indicates the major version number of the schema file of the selected manifest entry. DeviceManifestSchemaMinorVersion Indicates the minor version number of the schema file of the selected manifest entry. DeviceTLType Transport Layer type of the device. DeviceTLVersionMajor Major version of the Transport Layer of the device. DeviceTLVersionMinor Minor version of the Transport Layer of the device. DeviceTLVersionSubMinor Sub minor version of the Transport Layer of the device. Devic MaxThroughput Maximum bandwidth of the data that can be streamed out of the device. DeviceLinkSelector Selects which Link of the device to control.
No.19S185-01 56/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Name Description DeviceLinkSpeed [DeviceLinkSelector] Indicates the speed of transmission negotiated on the specified Link. DeviceLinkHeartbeatTimeout [DeviceLinkSelector] Controls the current heartbeat timeout of the specific Link. DeviceLinkCommandTimeout [DeviceLinkSelector] Indicates the command timeout of the specified Link. DeviceStreamChannelCount Indicates the number of streaming channels supported by the device. DeviceStreamChannelSelector Selects the stream channel to control. DeviceStreamChannelType [DeviceStreamChannelSelector] Reports the type of the stream channel. DeviceStreamChannelEndianness [DeviceStreamChannelSelector] Endianness of multi-byte pixel data for this stream. DeviceEventChannelCount Indicates the number of event channels supported by the device. DeviceCharacterSet Character set used by the strings of the device's bootstrap registers. DeviceReset Resets the device to its power up state. DeviceRegistersStreamingStart Prepare the device for registers streaming without checking for consistency. DeviceRegistersStreamingEnd Announce the end of registers streaming. DeviceRegistersEndianness Endianness of the registers of the device. DeviceTemperatureSelector Selects the location within the device, where the temperature will be measured. DeviceTemperature [DeviceTemperatureSelector] Device temperature in degrees Celsius (C). TimestampReset Resets the current value of the device timestamp counter. TimestampLatch Latches the current timestamp counter into Timestamp Latch Value. TimestampLatchValue Returns the latched value of the timestamp counter. DeviceUserMemory Read / Write the user data from / to the non-volatile memory.
No.19S185-01 57/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.2 ImageFormatControl
SensorWidth Effective width of the sensor in pixels. SensorHeight Effective height of the sensor in pixels. SensorShutterMode Sets the shutter mode of the device. WidthMax Maximum width of the image (in pixels). HeightMax Maximum height of the image (in pixels). BinningSelector Selects which binning engine is controlled by the Binning Horizontal and Binning Vertical features. BinningHorizontalMode [BinningSelector] Sets the mode to use to combine horizontal photo-sensitive cells together when Binning Horizontal is used. BinningVerticalMode [BinningSelector] Sets the mode used to combine vertical photo-sensitive cells together when Binning Vertical is used. BinningHorizontal [BinningSelector] Number of horizontal photo-sensitive cells to combine together. BinningVertical [BinningSelector] Number of vertical photo-sensitive cells to combine together. DecimationHorizontal Horizontal sub-sampling of the image. DecimationVertical Vertical sub-sampling of the image. RegionSelector Selects the Region of interest to control. RegionMode [RegionSelector] Controls if the selected Region of interest is active and streaming. Width [RegionSelector] Width of the image provided by the device (in pixels). Height [RegionSelector] Height of the image provided by the device (in pixels). OffsetX [RegionSelector] Horizontal offset from the origin to the region of interest (in pixels). OffsetY [RegionSelector] Vertical offset from the origin to the region of interest (in pixels). PixelFormat Format of the pixels provided by the device. PixelSize Total size in bits of a pixel of the image. PixelColorFilter Type of color filter that is applied to the image. ReverseX Flip horizontally the image sent by the device. ReverseY Flip vertically the image sent by the device. TestPatternGeneratorSelector Selects which test pattern generator is controlled by the Test Pattern feature. TestPattern [TestPatternGeneratorSelector] Selects the type of test pattern that is generated by the device as image source. TestPatternInputValue [TestPatternGeneratorSelector] Test Pattern Input Value
No.19S185-01 58/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.3 AcquisitionControl
AcquisitionMode Sets the acquisition mode of the device. AcquisitionStart Starts the Acquisition of the device. AcquisitionStop Stops the Acquisition of the device at the end of the current Frame. AcquisitionFrameCount Number of frames to acquire in Multi Frame Acquisition mode. AcquisitionFrameRate Controls the acquisition rate (in Hertz) at which the frames are captured. TriggerSelector Selects the type of trigger to configure. TriggerMode [TriggerSelector] Controls if the selected trigger is active. TriggerSoftware [TriggerSelector] Generates an internal trigger. TriggerSource [TriggerSelector] Specifies the internal signal or physical input Line to use as the trigger source. TriggerActivation [TriggerSelector] Specifies the activation mode of the trigger. TriggerDelay [TriggerSelector] Specifies the delay in microseconds (us) to apply after the trigger reception before activating it. ExposureMode Sets the operation mode of the Exposure. ExposureTimeSelector Selects which exposure time is controlled by the Exposure Time feature. ExposureTime [ExposureTimeSelector] Sets the Exposure time when Exposure Mode is Timed and Exposure Auto is Off. ExposureAuto Sets the automatic exposure mode when Exposure Mode is Timed. ExposureAutoLimitMin Determine the lower limit of exposure time when Exposure Auto is set to Continuous. ExposureAutoLimitMax Determine the upper limit of exposure time when Exposure Auto is set to Continuous.
No.19S185-01 59/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.4 AnalogControl
GainSelector Selects which Gain is controlled by the various Gain features. Gain [GainSelector] Controls the selected gain as an absolute physical value. GainAuto [GainSelector] Sets the automatic gain control (AGC) mode. GainAutoLimitMin [GainSelector] Determine the lower limit of gain when Gain Auto is set to Continuous. GainAutoLimitMax [GainSelector] Determine the upper limit of gain when Gain Auto is set to Continuous. AutoLuminanceTarget Target brightness for auto luminance control. AutoLuminanceRegionSelector Select the area for auto luminance control. AutoLuminanceWidth [AutoLuminanceRegionSelector] Determine width of targeted region for auto luminance control. AutoLuminanceHeight [AutoLuminanceRegionSelector] Determine height of targeted region for auto luminance control. AutoLuminanceOffsetX [AutoLuminanceRegionSelector] Determine X offset of targeted region for auto luminance control. AutoLuminanceOffsetY [AutoLuminanceRegionSelector] Determine Y offset of targeted region for auto luminance control. AutoLuminanceWeight [AutoLuminanceRegionSelector] Weight of the area determined by Auto Luminance Region Selector for auto luminance control. AutoLuminancePeak Ratio of peak and average for auto luminance control. BlackLevelSelector Selects which Black Level is controlled by the various Black Level features. BlackLevel [BlackLevelSelector] Controls the analog black level as an absolute physical value. DigitalGainOffsetMode Digital Gain Offset Mode is enabled. BalanceRatioSelector Selects which Balance ratio to control. (STC-MCE132POE) BalanceRatio [BalanceRatioSelector] Controls ratio of the selected color component to a reference color component. (STC-MCE132POE) BalanceWhiteAuto Controls the mode for automatic white balancing between the color channels. (STC-MCE132POE) BalanceWhiteAutoRegionSelector Select the area for auto white balance. (STC-MCE132POE) BalanceWhiteAutoWidth [BalanceWhiteAutoRegionSelector] Determine width of targeted region for auto white balance. (STC-MCE132POE) BalanceWhiteAutoHeight [BalanceWhiteAutoRegionSelector] Determine height of targeted region for auto white balance. (STC-MCE132POE) BalanceWhiteAutoOffsetX [BalanceWhiteAutoRegionSelector] Determine X offset of targeted region for auto white balance. (STC-MCE132POE) BalanceWhiteAutoOffsetY [BalanceWhiteAutoRegionSelector] Determine Y offset of targeted region for auto white balance. (STC-MCE132POE) Gamma Controls the gamma correction of pixel intensity.
No.19S185-01 60/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.5 LUTControl
LUTSelector Selects which LUT to control. LUTEnable [LUTSelector] Activates the selected LUT. LUTIndex [LUTSelector] Control the index (offset) of the coefficient to access in the selected LUT. LUTValue [LUTSelector] [LUTIndex] Returns the Value at entry LUT Index of the LUT selected by LUT Selector. LUTValueAll [LUTSelector] Accesses all the LUT coefficients in a single access without using individual LUT Index. PixelCorrectionAllEnabled Enable pixel correction for all pixels. PixelCorrectionIndex Determine index of targeted pixel for pixel correction. PixelCorrectionEnabled [PixelCorrectionIndex] Determine if targeted pixel is enabled for pixel correction. PixelCorrectionX [PixelCorrectionIndex] Determine x-coordinate of targeted pixel for pixel correction. PixelCorrectionY [PixelCorrectionIndex] Determine y-coordinate of targeted pixel for pixel correction.
11.6 DigitalIOControl
LineSelector Selects the physical line (or pin) of the external device connector or the virtual line of the Transport Layer to configure. LineMode [LineSelector] Controls if the physical Line is used to Input or Output a signal. LineFormat [LineSelector] Controls the current electrical format of the selected physical input or output Line. LineSource [LineSelector] Selects which internal acquisition or I/O source signal to output on the selected Line. LineInverter [LineSelector] Controls the inversion of the signal of the selected input or output Line. LineDebounceTime [LineSelector] Sets the value of the input line debouncer time. LineStatus [LineSelector] Returns the current status of the selected input or output Line. LineStatusAll Returns the current status of all available Line signals at time of polling in a single bitfield. UseOutputSelector Selects which bit of the User Output register will be set by User Output Value. UseOutputValue [UseOutputSelector] Sets the value of the bit selected by User Output Selector.
No.19S185-01 61/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.7 LogicBlockControl
LogicBlockSelector Specifies the Logic Block to configure. LogicBlockFunction [LogicBlockSelector] Selects the combinational logic Function of the Logic Block to configure. LogicBlockInputNumber [LogicBlockSelector] Specifies the number of active signal inputs of the Logic Block. LogicBlockInputSelector [LogicBlockSelector] Selects the Logic Block’s input to configure. LogicBlockInputSource [LogicBlockSelector] [LogicBlockInputSelector] Selects the source signal for the input into the Logic Block. LogicBlockInputInverter [LogicBlockSelector] [LogicBlockInputSelector] Selects if the selected Logic Block Input source signal is inverted.
11.8 SoftwareSignalControl
SoftwareSignalSelector Selects which Software Signal features to control. SoftwareSignalPulse [SoftwareSignalSelector] Generates a pulse signal that can be used as a software trigger.
11.9 CounterAndTimerControl
CounterSelector Selects which Counter to configure. CounterEventSource [CounterSelector] Select the events that will be the source to increment the Counter. CounterResetSource [CounterSelector] Selects the signals that will be the source to reset the Counter. CounterResetActivation [CounterSelector] Selects the Activation mode of the Counter Reset Source signal. CounterReset [CounterSelector] Does a software reset of the selected Counter and starts it. CounterValue [CounterSelector] Reads or writes the current value of the selected Counter. TimerSelector Selects which Timer to configure. TimerDuration [TimerSelector] Sets the duration (in microseconds) of the Timer pulse. TimerDelay [TimerSelector] Sets the duration (in microseconds) of the delay to apply at the reception of a trigger before starting the Timer. TimerTriggerSource [TimerSelector] Selects the source of the trigger to start the Timer. TimerTriggerActivation [TimerSelector] Selects the activation mode of the trigger to start the Timer. TimerValue [TimerSelector] Reads or writes the current value (in microseconds) of the selected Timer.
No.19S185-01 62/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.10 EventControl
EventSelector Selects which Event to signal to the host application. EventNotification [EventSelector] Activate or deactivate the notification to the host application of the occurrence of the selected Event. EventTest Data Category that contains all the data features related to the Event Test generated using the Test Event Generate command. EventExposureStartData Category that contains all the data features related to the Exposure Start Event. EventExposureEndData Category that contains all the data features related to the Exposure End Event. EventFrameTriggerData Category that contains all the data features related to the Frame Trigger Event. EventFrameStartData Category that contains all the data features related to the Frame Start Event. EventFrameEndData Category that contains all the data features related to the Frame End Event. EventLine0RisingEdgeData Category that contains all the data features related to the Line0 Rising Edge Event. EventLine0FallingEdgeData Category that contains all the data features related to the Line0 Falling Edge Event. EventLine2RisingEdgeData Category that contains all the data features related to the Line2 Rising Edge Event. EventLine2FallingEdgeData Category that contains all the data features related to the Line2 Falling Edge Event. EventBlockDiscardData Category that contains all the data features related to the Block Discard Event. EventActionLateData Category that contains all the data features related to the Action Late Event.
11.11 UserSetControl
UserSetSelector Selects the feature User Set to load, save or configure. UserSetLoad [UserSetSelector] Loads the User Set specified by User Set Selector to the device and makes it active. UseSetSave [UserSetSelector] Save the User Set specified by User Set Selector to the non-volatile memory of the device. UserSetDefault Selects the feature User Set to load and make active by default when the device is reset.
No.19S185-01 63/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.12 ChunkDataControl
ChunkModeActive Activates the inclusion of Chunk data in the payload of the image. ChunkSelector Selects which Chunk to enable or control. ChunkEnable [ChunkSelector] Enables the inclusion of the selected Chunk data in the payload of the image. ChunkCounterSelector Selects which counter to retrieve data from. ChunkCounterValue [ChunkCounterSelector] Returns the value of the selected Chunk counter. ChunkGainSelector Selects which Gain to return. ChunkGain [ChunkGainSelector] Returns the gain used to capture the image. ChunkExposureTimeSelector Selects which Exposure Time to return. ChunkExposureTime [ChunkExposureTimeSelector] Returns the exposure time used to capture the image. ChunkBlackLevelSelector Selects which Black Level to return. ChunkBlackLevel [ChunkBlackLevelSelector] Returns the black level used to capture the image included in the payload. ChunkLineStatusAll Returns the status of all the I/O lines at the time of the Frame Start internal event. ChunkTimerSelector Selects which timer to retrieve data from. ChunkTimerValue [ChunkTimerSelector] Returns the value of the selected Timer. ChunkDeviceTemperature Indicates the value of the temperature when the image was acquired.
11.13 ActionControl
ActionDeviceKey Provides the device key that allows the device to check the validity of action commands. ActionQueueSize Indicates the size of the scheduled action commands queue. ActionSelector Selects to which Action Signal further Action settings apply. ActionGroupMask [ActionSelector] Provides the mask that the device will use to validate the action on reception of the action protocol message. ActionGroupKey [ActionSelector] Provides the key that the device will use to validate the action on reception of the action protocol message.
No.19S185-01 64/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.14 FileAccessControl
FileSelector Selects the target file in the device. FileOperationSelector [FileSelector] Selects the target operation for the selected file in the device. FileOperationExecute [FileSelector] [FileOperationSelector] Executes the operation selected by File Operation Selector on the selected file. FileOpenMode [FileSelector] Selects the access mode in which a file is opened in the device. FileAccessBuffer Defines the intermediate access buffer that allows the exchange of data between the device file storage and the application. FileAccessOffset [FileSelector] [FileOperationSelector] Controls the Offset of the mapping between the device file storage and the File Access Buffer. FileAccessLength [FileSelector] [FileOperationSelector] Controls the Length of the mapping between the device file storage and the File Access Buffer FileOperationStatus [FileSelector] [FileOperationSelector] Represents the file operation execution status. FileOperationResult [FileSelector] [FileOperationSelector] Represents the file operation result. FileSize [FileSelector] Represents the size of the selected file in bytes.
11.15 TestControl
TestPendingAck Tests the device's pending acknowledge feature. TestEventGenerate Generates a Test Event.
No.19S185-01 65/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide
11.16 TransportLayerControl
PayloadSize Provides the number of bytes transferred for each image or chunk on the stream channel. PtpEnable Enable the Precision Time Protocol (PTP). PtpClockAccuracy Indicate the expected accuracy of the device PTP clock when it is the grandmaster, or in the event it becomes the grandmaster. PtpDataSetLatch Latches the current values from the device’s PTP clock data set. PtpStatus Returns the latched state of the PTP clock. PtpOffsetFromMaster The latched offset from the PTP master clock in nanoseconds. PtpClockID The latched clock ID of the PTP device. PTP Parent Clock ID. PtpParentClockID The latched parent clock ID of the PTP device. The parent clock ID is the clock ID of the current master clock. PtpGrandmasterClockID The latched grandmaster clock ID of the PTP device. The grandmaster clock ID is the clock ID of the current grandmaster clock. GevSupportedOptionSelector Selects the GEV option to interrogate for existing support. GevSupportedOption [GevSupportedOptionSelector] Returns if the selected GEV option is supported. GevInterfaceSelector Selects which logical link to control. GevMACAddress [GevInterfaceSelector] MAC address of the logical link. GevPAUSEFrameReception [GevInterfaceSelector] Controls whether incoming PAUSE Frames are handed on the given logical link. GevCurrentIPConfigurationLLA [GevInterfaceSelector] Controls whether the Link Local Address IP configuration scheme is activated on the given logical link. GevCurrentIPConfigurationDHCP [GevInterfaceSelector] Controls whether the DHCP IP configuration scheme is activated on the given logical link. GevCurrentIPConfigurationPersistentIP [GevInterfaceSelector] Controls whether the Persistent IP configuration scheme is activated on the given logical link. GevCurrentIPAddress [GevInterfaceSelector] Reports the IP address for the given logical link. GevCurrentSubnetMask [GevInterfaceSelector] Reports the subnet mask of the given logical link. GevCurrentDefaultGateway [GevInterfaceSelector] Reports the default gateway IP address to be used on the given logical link. GevIPConfigurationStatus [GevInterfaceSelector] Reports the current IP configuration status. GevPersistentIPAddress [GevInterfaceSelector] Controls the Persistent IP address for this logical link. GevPersistentSubnetMask [GevInterfaceSelector] Controls the Persistent subnet mask associated with the Persistent IP address on this logical link. GevPersistentDefaultGateway [GevInterfaceSelector] Controls the persistent default gateway for this logical link. GevGVCPExtendedStatusCodesSelector Selects the GigE Vision version to control extended status codes for.
No.19S185-01 66/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Name Description GevGVCPExtendedStatusCodes [GevGVCPExtendedStatusCodesSelector] Enables the generation of extended status codes. GevGVCPPendingAck Enables the generation of PENDING_ACK. GevPrimaryApplicationSwitchoverKey Controls the key to use to authenticate primary application switchover requests. GevGVCPExpendedIDMode Enables the extended IDs mode. GevCCP Controls the device access privilege of an application. GevPrimaryApplicationSocket Returns the UDP source port of the primary application. GevPrimaryApplicationIPAddress Returns the address of the primary application. GevMCPHostPort Controls the port to which the device must send messages. GevMCDA Controls the destination IP address for the message channel. GevMCTT Provides the transmission timeout value in milliseconds. GevMCRC Controls the number of retransmissions allowed when a message channel message times out. GevMCSP This feature indicates the source port for the message channel. GevStreamChannelSelector Selects the stream channel to control. GevSCPInterfaceIndex [GevStreamChannelSelector] Index of the logical link to use. GevSCPHostPort [GevStreamChannelSelector] Controls the port of the selected channel to which a GVSP transmitter must send data stream or the port from which a GVSP receiver may receive data stream. GevSCPSFireTestPacket [GevStreamChannelSelector] Sends a test packet. GevSCPSDoNotFragment [GevStreamChannelSelector] The state of this feature is copied into the "do not fragment" bit of IP header of each stream packet. GevSCPSPacketSize [GevStreamChannelSelector] This GigE Vision specific feature corresponds to DeviceStreamChannelPacketSize and should be kept in sync with it. GevSCFTD [GevStreamChannelSelector] Controls the delay (in GEV timestamp counter unit) to insert between each packet for this stream channel. GevSCPD [GevStreamChannelSelector] Controls the delay (in GEV timestamp counter unit) to insert between each frame for this stream channel. GevSCDA [GevStreamChannelSelector] Controls the destination IP address of the selected stream channel to which a GVSP transmitter must send data stream or the destination IP address from which a GVSP receiver may receive data stream. GevSCSP [GevStreamChannelSelector] Indicates the source port of the stream channel.
No.19S185-01 67/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide Rev Date Changes Note 00 2019/05/31 New Document 01 2019/06/07 Revised Added “LWIP TCP/IP Licensing” information GigE Vision is trademark of AIA. GenICam is trademark of EMVA. Other company names and product names in this document are trademarks of their respective owners.
No.19S185-01 68/68 STC-MBE132POE / STC-MCE132POE Product Specifications and User’s Guide 19F, Ebina Prime Tower 9-50, Chuo 2 chome Ebina-city, Kanagawa 243-0432 Japan TEL 81-46-236-6660 FAX 81-46-236-6661 URL http://www.sentech.co.jp/