ST777 STMICROELECTRONICS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
■ 1V TO 6V INPUT GUARANTEES START-UP UNDER LOAD ■ MAXIMUM OUTPUT CURRENT OF 300mA (778 OR 779 ADJUSTED TO 3V) ■ LOAD FULLY DISCONNECTED IN SHUTDOWN ■ TYPICAL EFFICIENCY OF 82% ■ INTERNAL 1A POWER SWITCH AND SYNCHRONOUS RECTIFIER ■ ADJUSTABLE CURRENT LIMIT ALLOWS LOW-COST INDUCTORS ■ SUPPLY CURRENT OF 270µA (NO LOAD) ■ SHUTDOWN SUPPLY CURRENT 20µA ■ PACKAGE AVAILABLE: DIP-8 AND SO-8
DESCRIPTION
The ST777/778/779 are dc-dc converters that step-up from low voltage inputs requiring only three external components, an inductor (typically 22µH) and two capacitors. The device include a Sinchronous Rectifier that eliminates the need for an external catch diode, and allows regulation even when the input is greater than the output. Unlike others step-up DC-DC converters the ST777/778/779’s Sinchronous Rectifier turns off in the shutdown mode, fully disconnecting the output from the source. This eliminates the current drain associated with conventional step-up converters when off or in shutdown. Supply current is 270µA under no load and only 20µA in stand by mode. ST777/778/779 LOW VOLTAGE INPUT, 3-3.3V/5V/ADJUSTABLE OUTPUT DC-DC CONVERTER WITH SYNCHRONOUS RECTIFIER VIN VO 22µH 100µF 100µF RLIM ILIM LXIN OUT PGND SEL AGND SHDN 1.25V VREF SHUTDOWN CONTROL DELAY TIMER DELAY TIMER tOFF tON SWITCH DRIVER ACTIVE RECTIFIER RECTIFIER CONTROL 1:N SCHEMATIC DIAGRAM SO-8DIP-8
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. ORDERING CODES CONNECTION DIAGRAM PIN CONNECTIONS THERMAL DATA Symbol Parameter Value Unit VCC DC Input Voltage to GND -0.3 to +7 V LX Switch off Pin Voltage -0.3 to +7 V Switch on Pin Voltage 30 sec short to IN or OUT OUT, SHDN Output, Shutdown Voltage -0.3 to +7 V AGND to PGND Analog and Power Ground -0.3 to +0.3 V FB FB Pin Voltage -0.3 to (OUT+0.3) V PTOT Continuous Power Dissipation (at TA = 85°C) DIP-8 550 mWContinuous Power Dissipation (at TA = 85°C) SO-8 344 TSTG Storage Temperature Range -40 to 150 °C TOP Operating Ambient Temperature Range 0t o8 5 ° C TYPE DIP-8 SO-8 ST777 ST777ACN ST777ACD ST778 ST778ACN ST778ACD ST779 ST779ACN ST779ACD Pin No. SYMBOL NAME AND FUNCTION 1 ILIM Sets switch current limit input. Connect to IN for 1A current limit. A resistor from ILIM to IN sets lower peak inductor currents.
2 IN Input from battery
3 AGND Analog ground. Not internally connected to PGND. 4 PGND Power ground. Must be low impedance; solder directly to ground plane or star ground. Connect to AGND, close to the device. 5 LX Collector of 1A NPN power switch and emitter of Sinchronous Rectifier PNP . 6 OUT Voltage Output. Connect filter capacitor close to pin. 7S H D N Shutdown input disables power supply when low. Also disconnets load from input. Threshold is set at VIN/2. 8 SEL/N.C./FB - Selection pin for 3/3.3V version (778); - Not internally connected for 5V version (777); - Feedback pin for adjustable version (779). Symbol Parameter DIP-8 SO-8 Unit Rthj-amb Thermal Resistance Junction-ambient 100 160 °C/W
ELECTRICAL CHARACTERISTICS (VIN=2.5V, CI= 22µF, CO =100µF, SHDN and ILIM connected to IN, AGND connected to PGND, TA =0 to 85°C, unless otherwise specified. Typical values are referred at TA=25°C) Note 1:Output in regulation, VOUT =V OUT (nominal)± 4% . Note 2:At hight VIN to VOUT differentials, the maximum load current is limited by the maximum allowable power dissipation in the package. Note 3:Start-up guaranteed under these load conditions. Note 4:Minimum value is production tested. Maximum value is guaranteed by design and is not production tested. Note 5:In the ST779 supply current depends on the resistor divider used to set the output voltage. Note 6:VOUT is set to a target value of +5V by 0.1% external feedback resistors. VOUT is measured to be 5V±2.5% to guarantee the error comparator trip point. Symbol Parameter Test Conditions Min. Typ. Max. Unit VSTART Start up Voltage I LOAD < 10mA, TA = 25°C (Note 1) 1 V V IN(MAX) Maximum Input Voltage (Note 1,2) 6 V VO Output Voltage ST777 779 (set to 5V), (Note 3) ILOAD ≤ 30mA, VIN = 1.1V to 5V or ILOAD ≤ 80mA, VIN = 1.8V to 5V or ILOAD ≤ 130mA, VIN = 2.4V to 5V 4.8 5.0 5.2 V Output Voltage ST778 (Note 3) SEL=0V ILOAD ≤ 50mA,V IN =1.1V to 3.3V or ILOAD ≤ 210mA,V IN =1.8V to 3.3V or ILOAD ≤ 300mA,V IN =2.4V to 3.3V 3.17 3.30 3.43 V SEL=OPEN ILOAD ≤ 30mA, VIN =1.1V to 3V or ILOAD ≤ 210mA, VIN =1.8V to 3V or ILOAD ≤ 300mA, VIN =2.4V to 3V 2.88 3.00 3.12 V Output Voltage Range ST779 (Note 4) 2.7 6.5 V IIN No Load Supply Current ILOAD = 0 mA, (Switch ON) (Note 5) 270 µA ISHDN Shutdown Supply Current SHDN =0V, (Switch OFF) 20 35 µA IIN SHDN Shutdown Input Current SHDN = 0 to VIN 15 100 nA SHDN =V IN to 5V 12 40 µA υ Efficiency I LOAD =100mA 82 % VIH Shutdown Input Threshold VIN=1V to 6V V IN/2 + 0.25 V ILIM Current Limit 1.0 A ILIM TEMPCO Current Limit Temperature Coefficient -0.3 %/°C tOFFMIN Minimum Switch Off Time 1.2 µs tONMAX Maximum Switch ON Time V IN=2.5V 4.5 VIN=1.8V 6.5 VIN=1V 15 VCESAT NPN Switch saturation Voltage ISW =400mA 0.25 V ISW =600mA 0.33 ISW =1000mA 0.5 VCESAT NPN Rectifier Forward Drop ISW =400mA 0.18 V ISW =600mA 0.22 ISW =1000mA 0.4 VFB Error Comparator Trip Point ST779, over operating input voltage (Note 6) 1.23±2% V IFB FB Pin Bias Current ST779, V FB =1.3V 50 nA ILX Switch Off Leakage Current 0.1 µA Rectifier Off Leakage Current 0.1 µA
TYPICAL APPLICATION CIRCUIT APPLICATIONS INFORMATION R1 and R2 must be placed only in ST779 applications to set the output voltage according to the following equation: VOUT = (1.23) [(R1+R2)/R2] and to simplify the resistor selection: R1 = R2 [(VOUT /1.23)-1] It is possible to use a wide range of values for R2 (10KΩ to 50KΩ ) with no significant loss of accuracy thanks to the very low FB input current. To have 1% error, the current through R2 must be at least 100 times FB’s bias current. When large values are used for the feedback resistors (R1>50KΩ ), stray output impedance at FB can incidentally add "lag" to the feedback response, destabilizing the regulator and creating a larger ripple at the output. Lead lengths and circuit board traces at the FB node should be kept short. Compensate the loop by adding a "lead" compensation capacitor (C3, 100pF to 1nF) in parallel with R1. The typical value of the L1 inductor is 22µH, enough for most applications. However, are also suitable values ranging from 10µF to 47µF with a saturation rating equal to or greater than the peak switch -current limit. Efficiency will be reduced if the inductor works near its saturation limit, while will be maximized using an inductor with a low DC resistance, preferably under 0.2Ω. Connecting ILIM to V IN the maximum LX current limit (1A) is set. If this maximum value is not required is possible to reduce it connecting a resistor between ILIM and V IN ( S e eF i g u r e1 6t o choose the right value). The current limit value is misured when the switch current through the inductor begins to flatten and does’nt coincide with the max short circuit current. Even if the device is designed to tolerate a short circuit without any damage, it is strictly recommended to avoid a continuos and durable short circuit of the output to GND. To achieve the best performances from switching power supply topology, particular care to layout drawing is needed, in order to minimize EMI and obtain low noise. Moreover, jitter free operation ensures the full device functionality. Wire lengths must be minimized, filter and by-pass capacitors must be low ESR type, placed as close as possible to the integrated circuit. Solder AGND and PGND pins directly to a ground plane. ST777 ST778 ST779 ILIM 22µH SEL / N.C. / FB R1V+ LX Vout SHDN ____ AGND 22µF 100µF Vin 1÷6V Vo PGND
DIM. mm. inch A 3.3 0.130 a1 0.7 0.028 B 1.39 1.65 0.055 0.065 B1 0.91 1.04 0.036 0.041 b 0.5 0.020 b1 0.38 0.5 0.015 0.020 D 9.8 0.386 E 8.8 0.346 e 2.54 0.100 e3 7.62 0.300 e4 7.62 0.300 F 7.1 0.280 I 4.8 0.189 L 3.3 0.130 Z 0.44 1.6 0.017 0.063 Plastic DIP-8 MECHANICAL DATA P001F
DIM. mm. inch A 1.75 0.068 a1 0.1 0.25 0.003 0.009 a2 1.65 0.064 a3 0.65 0.85 0.025 0.033 b 0.35 0.48 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.25 0.5 0.010 0.019 c1 45˚ (typ.) D 4.8 5.0 0.189 0.196 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F 3.8 4.0 0.149 0.157 L 0.4 1.27 0.015 0.050 M 0.6 0.023 S ˚ (max.) SO-8 MECHANICAL DATA 0016023
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com