SSF-2F-10 MERRIMAC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Ampl. Balance 0 dB 0.25 0.5 0.75 1.0 2.0 dB General Notes: 1. Single Sideband Modulators are integrated networks composed of an in-phase power divider, two double balanced mixers and two 90°quadrature hybrids. The primary function of the circuit is to amplitude modulate a carrier such that all the energy is in either the upper or lower sideband. 2. These units are especially useful in modulator applications where the desired and undesired RF sidebands are so close in frequency that it is not practical to use a bandpass filter to separate them or where minimum group delay is required. 3. By vector subtraction, the undesired sideband is canceled within the unit (internally terminated) and the desired sideband is reinforced at the output. The level of cancellation is usually expressed as sideband rejection ratio in dB. 4. The schematic diagram shows how the desired receiver signals from the two mixers are combined in-phase at the real (RF/LO) port, while the undesired spurious signals cancel each other out. At the image port the reverse occurs and the unwanted sideband signal is absorbed by the load resistor. (Continued, next page) SIDEBAND REJECTION Phase Error (degrees) for a given Amplitude and Phase Balance 0 0.5 1 1.5 2 2.5 3 Image Rejection Ratio PRINCIPAL SPECIFICATIONS Model LO Center Bandwidth, Outline Number Frequency, fo MHz Style SSF-2F-*/ 10 - 1000 MHz 10% of f o F SSF-2L/ 1000 - 4000 MHz 10% of f o L A complete Model Number will be assigned with center frequency (*=f o ) and slash number, once a full specification is established with factory. SINGLE SIDEBAND MODULATORSSF-2 Series 10 to 4000 MHz / Image Rejection to 30 dB / Internal Second Quad / High Sideband Rejection Fo r f u rther infor m at ion contact MERRIMAC / 41 Fairfield Pl., West Caldwell, NJ, 07006 / 973-575-1300 / FAX 973-575-0531 26Mar96 GENERAL SPECIFICATIONS (when used as an Up Converter) RF/IF Input Characteristics Impedance: 50 Ω nom. VSWR: 1.5:1 max. RF Power Level: +10 dBm IF Power Level: 0 dBm nom. IF Bandwidth: up to an octave RF Bandwidth: 10% Output Characteristics Conversion Loss: 9 dB max. Sideband Suppression: 25 dB min. Operating Temperature: -- 55 to +85°C

NOTES: 1. Tolerance on 3 place decimals ±.010(.25) except as noted. 2. Dimensions in inches over millimeters. 3. Dimensions marked with * apply only at body. 4. All unmarked pins are case ground. 5. Nominal Weight: 0.55 oz (15.4 g) F-Package Outline NOTES: 1. Tolerance on 3 place decimals ±.010(.25) except as noted. 2. Dimensions in inches over millimeters. 3. Dimensions marked with * apply only at body. 4. All unmarked pins are case ground. SSF-2L series SSF-2 Series SINGLE SIDEBAND MODULATOR 10 to 4000 MHz / Image Rejection to 30 dB / Internal Second Quad / High Sideband Rejection Fo r f u rther infor m at ion contact MERRIMAC / 41 Fairfield Pl., West Caldwell, NJ, 07006 / 973-575-1300 / FAX 973-575-0531 General Notes (Continued) 5. From a practical standpoint, there are may considerations affecting sideband suppression, such as the phase and amplitude balances of the individual components chosen, mixer sensitivity, VSWR interaction, bandwidth, etc. 6. The most useful guide to how much signal rejection may be expected for a given phase error and am plitude balance is shown in the graph. These curves allow determination of the trade-off between the allowable phase and amplitude errors for a d esired image rejection ratio. 7. Merrimac offers a wide range of Single Sideband Modulators to a variety of specifications. The pa rameters quoted for the SSF series are a basis only for more exacting requirements. The the minimum image rejection and package size will be impacted mo st by an increase in bandwidth requirements. 8. Merrimac Single Sideband Modulators comply with applicable portions of MIL-M-28837 and can be sup plied screened for additional specifications you specify for military and aerospace applications requiring higher reliability. 29Apr96