SS5GL-13F

SS5GL-13F OMRON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

Subminiature Snap Action Switch

• Economical, subminiature snap action switch offers long service life (30 million operations minimum)  All models are free from overtravel restrictions, permit easy setting  Wide switching capacity range from microvoltage/current loads (1 mA at 5 VDC to high-capacity loads 10.1 A at 250 VAC)  Standard operating force, low force or super-low force models available  RoHS Compliant

Ordering Information

Tab (#110) terminalStraight Left-angled Right-angled

0.1 A Pin plunger 25 g SS-01-ED — — SS-01-E SS-01-ET

50 g SS-01-FD — — SS-01-F SS-01-FT 150 g SS-01D SS-01D1 SS-01D2 SS-01 SS-01T Hinge lever 8 g SS-01GL-ED — — SS- 01GL-E SS-01GL-ET 16 g SS-01GL-FD — — SS-01GL-F SS-01GL-FT 50 g SS-01GLD SS-01GLD1 SS-01GLD2 SS-01GL SS-01GLT Simulated roller lever 8 g SS-01GL13-ED — — SS-01GL13-E SS-01GL13-ET 16 g SS-01GL13-FD — — SS-01GL13-F SS-01GL13-FT 50 g SS-01GL13D — — SS-01GL13 SS-01GL13T Hinged roller lever 8 g SS-01GL2-ED — — SS-01GL2-E SS-01GL2-ET 16 g SS-01GL2-FD — — SS-01GL2-F SS-01GL2-FT 50 g SS-01GL2D — — SS-01GL2 SS-01GL2T

5 A Pin plunger 50 g SS-5-FD SS-5-FD1 SS-5- FD2 SS-5-F SS-5-FT

150 g SS-5D SS-5D1 SS-5D2 SS-5 SS-5T Hinge lever 16 g SS-5GL-FD SS-5GL-FD1 SS-5G L-FD2 SS-5GL-F SS-5GL-FT 50 g SS-5GLD SS-5GLD1 SS-5GLD2 SS-5GL SS-5GLT Simulated roller lever 16 g SS-5GL13-FD — SS-5GL13-FD 2 SS-5GL13-F SS-5GL13-FT 50 g SS-5GL13D SS-5GL13D1 SS-5GL13D2 SS-5GL13 SS-5GL13T Hinge roller lever 16 g SS-5GL2-FD SS-5GL2-FD1 SS-5G L2-FD2 SS-5GL2-F SS-5GL2-FT 50 g SS-5GL2D SS-5GL2D1 SS-5GL2D2 SS-5GL2 SS-5GL2T

10 A Pin plunger

150 g SS-10D — — SS-10 SS-10T Hinge lever 50 g SS-10GLD — — SS-10GL SS-10GLT Simulated roller lever 50 g SS-10GL13D — — SS-10GL13 SS-10GL13T Hinge roller lever 50 g SS-10GL2D — — SS-10GL2 SS-10GL2T

96 Snap Action Switch SS

■Characteristics Note: 1. Data shown are of initial value. 2. The dielectric strength values shown is measured using a separator between the switch and metal mounting plate. 3. For pin plunger models, the above value apply for use at the free position and total travel position. For the lever models, the values apply at the total travel position. Operating speed 0.1 mm to 1 m/second (pin plunger models) Operating frequency Mechanical: 400 operations per minute max. Electrical: 30 operations per minute max. Insulation resistance 100 MΩ at 500 VDC Contact resistance 150 gf: SS-10, SS-5 models: 30 m Ω max. SS-01 models: 50 m Ω max. 50 gf: SS-5 models: 50 m Ω max. SS-01 models 100 m Ω max. 25 gf: SS-01 models 150 m Ω max. Dielectric strength (See note 2) 1,000 VAC (600 VAC for SS-01), 50/60 Hz for 1 minute between terminals of same polarity 1,500 VAC, 50/60 Hz for 1 minute between current-carrying metal parts and ground and between each terminal and noncurrent-carrying metal parts Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5 mm double amplitude Shock resistance (see note 3) 150 gf: Destruction: 1,000 m/s 2 (approx. 100G) max. Malfunction: 300 m/s2 (approx. 30G) max. 50 gf and 25gf: Destruction: 500 m/s 2 (approx. 50G) max. Malfunction: 200 m/s2 (approx. 20G) max. Degree of protection IEC IP40 Degree of protection against electric shock Class I Proof tracking index (PTI) 175 Ambient operating temperature -25° to 85°C (at 60% RH max.) with no icing Ambient operating humidity 85% max. (for 5°C to 35°C) Service life Mechanical: 30 million operations min. at 60 operations per minute (SS-01, SS-5) 10 million operations min. at 60 operations per minute (SS-10) Electrical: 200,000 operations min. at 30 operations per minute (SS-01, SS-5) 50,000 operations min. at 30 operations per minute (SS-10) Weight Approx. 1.6 g pin plunger type SS- 1. Ratin gs 10: 10.1 A at 125 VAC 5: 5 A at 125 VAC 01: 0.1 A at 30 VDC 3. Maximum Operatin g Force (see note) None: 150 gf -F: 50 gf (0.1A and 5A versions) -E: 25 gf (0.1A versions) 4. Contact Form None: SPDT -2: SPST-NC -3: SPST-NO Note: These OF values are for the pin plunger models. 2. Actuator None: Pin pl unger GL: Hinge le ver GL13: Sim ulated roller lever GL2: Hinge roller le ver 5. Terminals None: Solder terminals T: Q uick-connect terminals (#110) D: Straight PCB terminals D1: Left-angled PCB terminals D2: Right-angled PCB terminals 3 4 521 Consult Omron regarding the following: - SPST-NC and SPST-NO versions - High temperat ure versions that are rated from -25°C to 120°C - Left and Right angled PCB terminal versions

■Ratings (reference values) Note: 1. Data in parentheses apply to the SS-10 models only. 2. The above current ratings are the values of the steady-state current. same as that of SS-5. 4. Lamp load has an inrush current of 10 times the steady-state current 5. Motor load has an inrush current of 6 times the steady-state current. 6. If the switch is used in a DC circuit and is subjected to inrush current or surge, connect a surge suppressor across the switch. 7. The electrical rating applies under the following test conditions: Ambient Temperature = 20±2°C, Ambient Humidity = 65±5%, Operating frequency = 30 operations/minute ■Approved Standards UL Recognized (File No. E41515) CSA Certified (File No. LR21642) EN61058-1 - - VDE approval (File No. 129246 for SS-5, 125256 for SS-10) EN61058-1 - - TÜV Rheinland approval (File No. J9451450) Testing conditions: 5E4 (50,000 operations), T85 (0°C to 85°C) Note: The rated values approved by each of the safety standards (e.g. UL, CSA) may be different from the performance charac- teristics individually defined in this catalog. ■Contact Specifications Note: Minimum applicable loads are indicated by N standard refer- ence values. This value represents the failure rate at a 60% (λ60) reliability level (JIS C5003). The equation λ60=0.5 x 10-6 / operations indicates that a failure rate of 1/2,000,000 operations can be expected at a reliability level of 60% Switch series: Contact form SS-10 and SS-5 SS-01 Resistive load Lamp load Inductive load Motor load Resistive Load NC NO NC NO NC NO NC NO NC NO 250 VAC 3 A (10.1A) 1 A 0.5 A 2 A 1.5 A 0.8 A - - - 8 VDC 5 A (10.1A) 2 A 5 A 4 A 3 A 0.1 A 14 VDC 5 A (10.1A) 2 A 4 A 3 A 0.1 A 30 VDC 4 A 2 A 3 A 3 A 0.1 A 125 VDC 0.4 A 0.05 A 0.4 A 0.05 A - - - 250 VDC 0.2 A 0.03 A 0.2 A 0.03 A - - - Rated Voltage SS-10 SS-5 SS-01 125 VAC - - - 5 A 0.1 A 250 VAC 10.1 A 3 A - - - Rated Voltage SS-10 SS-5 250 VAC 10.1 A 5 A Rated Voltage SS-10 SS-5 250 VAC 10.1 A 5 A Item SS-10 SS-5 SS-01 Specification Rivet Crossbar Material Silver alloy Sil ver Gold alloy Gap (standard value) 0.5 mm 0.25 mm Inrush current NC: 20A max. NO: 15A max. NC: 20A max. NO: 10A max. 1A max. Minimum applicable load (see note) 160 mA at 5 VDC 1 mA at 5 VDC

98 Snap Action Switch SS

■Mechanical Service Life ■Electrical Service Life ■Mounting Panel Mounting All switches may be panel mounted using M2.3 mounting screws with plane washers or spring washers to securely mount the switch. Tighten the screws to a torque of 0.23 to 0.26 N·m.PCB Layout ■Contact Form * Consult Omron for SPST - NC and SPST -NO contact form types ordering information. (Pin Plunger Models) SS-01, SS-5 Models Overtravel (mm) Number of operations (x10 )3 40,000 30,000 20,000 10,000 5,000 Ambient temperature: 20±2°C Ambient humidity: 65±5% Without load Operating frequency: 60 operations/min (Pin Plunger Models) SS-5 Models Switching current (A) Number of operations (x10 )3 5,000 3,000 1,000 500 300 100 0 123 4567

125 VAC

250 VAC

Ambient temperature: 20±2°C Ambient humidity: 65±5% Operating frequency: 30 operations/min cosφ = 1 Two, 2.4-dia. mounting holes or M2.3 screw holes 9.5 ± 0.1 Three, 1.35 to 1.5 dia. 8.8+0.15 –0.05 (1.6) 16.1±0.1 SPDT SPST-NC SPST-NO COM NC COM NO NC COM NO

■Terminals Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. Terminal plate thickness is 0.5 mm for all models. ■Dimensions and Operating Characteristics Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations and dimensions are for solder terminal models. Refer to “Terminals” for models with quick-connect terminals (#110) or PCB terminals. 3. The operating characteristics are for operation in the A direction( ) Note: Terminal plate thickness is 0.5 mm for all models. Solder Terminals Quick-connect Terminals (#110) PCB Terminals Three, 1.6-dia. holes Three, 1.2 dia. t = 0.5 COM terminal (C) NO terminal NC terminal COM terminal (C) NO terminal NC terminal COM terminal (C) NO terminal NC terminal 2.9 1.6 8.8 7.3 9.5±0.1 19.8 3.3 0.6 7.0 0.5 1.2 3.2 2.9 1.6 8.8 7.3 9.5±0.1 19.8 6.4 3.2 6.4 2.9 1.6 8.8 7.3 9.5±0.1 19.8 10.6 2.8 3.2 7.1 NC terminal NO terminal COM terminal PCB, Right-angled terminal NC terminal NO terminal COM terminal PCB, Left-angled terminal Note: Angled terminal directions are shown below. Left-angled terminal Ri ght-angled terminal Pin Plunger Models SS-01(-E, -F) SS-5(-F) SS-10 2.35+0.075 –0.05 dia. holes 2.35+0.075 –0.05 Three, 1.6 dia. 10.29.5 7.5 PT OP 6.4 2.9 2.5 1.6 8.8 7.3 5.1 19.8 2.5±0.07 dia. 3.2 6.4 3.2 6.4 9.5±0.1 A Characteristics Part number SS-01-E SS-01-F, SS-5-F SS-01, SS-5 SS-10 OF max. 25 g 50 g 150 g 150 g RF min. 2 g 4 g 25 g 25 g OP 8.4 ± 0.5 mm

100 Snap Action Switch SS

SS-01GL(-E, -F) SS-5GL(-F) SS-10GL 2.35+0.075 –0.05 Three, 1.6 dia. t = 0.3 (see note 1) 2.35+0.075 –0.05 dia. holes 6.4 3.2 6.4 3.614.5 (see note 2) FPOP 10.29.5 2.5±0.07 dia. 2.52.9 8.8 7.3 5.1 Note: 1. Stainless-steel le ver 2. Besides the SS- GL models with a hinge lever length of 14.5, the SS- GL11 models with a hinge lever length of 18.5, the SS- GL111 models with a hinge lever length of 22.6, and the SS- GL1111 models with a hinge lever length of 37.8 are available. Contact your OMRON representative for these models 19.8 9.5±0.1 1.6 A Characteristics SS-01GL-E SS-01GL-F , SS-5GL-F SS-01GL, SS-5GL SS-10GL OF max. 8 g 16 g 50 g 50 g RF min. 1 g2 g6 g6 g FP max. 13.6 mm OP 8.8 ± 0.8 mm Simulated Roller Lever Models SS-01GL13(-E, -F) SS-5GL13(-F) SS-10GL13 2.35+0.075 –0.05 Three, 1.6 dia.2.35+0.075 –0.05 dia. holes 1.3R t = 0.3 (see note) 2.5±0.07 dia. FPOP 10.29.5 6.4 3.2 6.4 3.6 8.8 7.3 5.1 15.8 2.52.9 Note: Stainless-steel spring lever19.8 9.5±0.1 1.6 A Characteristics SS-10GL13-E SS-10GL13-F, SS-5GL13-F SS-01GL13, SS-5GL13 SS-10GL13 OF max. 8 g 16 g 50 g 50 g RF min. 1 g2 g6 g6 g FP max. 15.5 mm OP 10.7±0.8 mm Hinge Roller Lever Models SS-01GL2(-E, -F) SS-5GL2(-F) SS-10GL2 Three, 1.6 dia. 2.35+0.075 –0.05 dia. 2.35+0.075 –0.05 dia. holes 4.8 dia. × 3.2 (see note 2) Note: 1. Stainless-steel spring le ver 2. Polyacetal resin roller 2.5±0.07 dia. t = 0.3 (see note 1) 2.52.9 14.5 FPOP 10.29.5 6.4 8.8 7.3 5.1 19.8 3.2 6.4 9.5±0.1 1.6 A Characteristics SS-01GL2-E SS-01GL2-F, SS-5GL2-F SS-01GL2, SS-5GL2 SS-10GL2 OF max. 8 g 16 g 50 g 50 g RF min. 1 g2 g6 g6 g FP max. 19.3 mm OP 14.5 ± 0.8 mm

Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide, “Snap Action Switches, Technical Information” for correct use. ■Correct Use Mounting Mount the switch onto a flat surface. Mounting on an uneven surface may cause deformation of the switch, resulting in faulty operation or breakage in the housing. Operating Stroke Take particular care in setting the operating stroke for the pin plunger models. Make sure that the operating stroke is 70% to 100% of the rated OT distance. Do not operate the actuator exceeding the OT dis- tance, otherwise the life expectancy of the switch may be shortened. Using Microloads Using a model for ordinary loads to switch microloads may result in faulty operation. Instead, use the models that are designed for microloads and that operate in the following range; However, even when using microload models within the operating range shown above, if inrush current or inductive voltage spikes occur when the contact is opened or closed, then contact wear may increase and so decrease the service life. Therefore, insert a contact protection circuit where necessary. ■Cautions Handling Turn OFF the power supply before mounting or removing the switch, wiring, or performing maintenance for inspection. Failure to do so may result in electric shock or burning Terminal Connection When soldering the lead wire to the terminal, first insert the lead wire conductor through the terminal hole and then solder. Make sure that the capacity of the soldering iron is 60 W maximum. Do not take more than 5 seconds to solder the switch terminal. Improper soldering involving an excessively high temperature or excessive soldering time may deteriorate the characteristics of the switch. Be sure to apply only the minimu m required amount of flux. The switch may have contact failures if flux intrudes in the interior of the switch. Use the following lead wires to connect to the solder terminals; If the PCB terminal models are soldered in a solder bath, flux will per- meate inside the switch and cause contact failure. Therefore, manu- ally solder the PCB terminal. Wire the quick-connect terminals (#110) with receptacles. Insert the terminals straight into the receptacles. Do not impose excessive force on the terminal in the horizontal direction, otherwise the termi- nal may be deformed or the housing may be damaged. Insulation Distance Use a separator between the switch and metal mounting panels, to ensure proper dielectric characteristics are achieved. According to E N61058-1, the minimum insulation thickness for this switch should be 1.1 mm and minimum clearance distance between the terminal and mounting plate should be 1.6 mm. If the insulation distance cannot be provided in t he product incorporating the switch, either use a switch with insulation barrier or use a separator to ensure sufficient insulation distance. Operating range for micro load models SS-01 Operating range for general-load models SS-5, SS-10 Current (mA) Voltage (V) Inoperable range 1,000100101 100mA 100mA 160mA 26mA 1mA 0.16mA Model Conductor size SS-5 0.5 to 0.75 mm2 SS-10 0.75 mm2 Separator

Global - http://www.omron.com USA - http://www.components.omron.com Cat. No. X303-E-1 Printed in USA OMRON ELECTRONIC COMPONENTS LLC 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 11/10 Specifications subject to change without notice All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.