SS49 HONEYWELL | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
Installation Instructions for the ISSUE 2 SS49/SS19 Series Analog Position Sensors PK 88740 MICRO SWITCH Sensing and Control PERSONAL INJURY
- DO NOT USE these products as safety or emergency stop devices, or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. SS49/SS19 ELECTRICAL CHARACTERISTICS Supply Voltage 4 to 10 VDC Supply Current 4 mA typ. Output Type Analog Sourcing Output Voltage @ 0 Gauss, 25°C 1.75 to 2.25 V @ 5 V Sensitivity (measured between -400 and +400 gauss), mV/G Min. 0.60 Typ. 0.90 Max. 1.25 Operating Temperature -40 to +100°C (-40 to 212°F) ABSOLUTE MAXIMUM RATINGS Supply Voltage (Vs) ± 12 VDC Output Current 20 mA Storage Temperature -55 to +150°C (-67 to +302°F) Magnetic Flux No limit. Circuit cannot be damaged by magnetic overdrive. Absolute maximum ratings are the extreme limits the device will withstand without damage to the device. However, the electrical and mechanical characteristics are not guaranteed as the maximum limits (above recommended operating conditions) are approached, nor will the device necessarily operate at absolute maximum ratings. SOLDERING/ASSEMBLY SS49 Support leads during any forming/shearing operation. Do not stress leads inside plastic case. Hand soldering - Use 60/40 rosin core solder, and a 399°C (750°F) controlled temperature, 1/8” chisel tip soldering iron. Do not hold iron on terminals for more than four seconds. Lead temperature at package must not exceed 250°C (482°F). Wave soldering - Use Loncoflux 106A35 or equivalent. Set preheaters at 95°C (200°F) for top (component side) of PC board just prior to entering wave. (This may be adjusted depending upon board thickness.) Set solder temperature at 252°C to 260°C max. (485°F to 500°F). Set conveyor speed to about 4.5 feet per minute (1,37 meter/min.), choosing a speed which gives full solder fillets and minimum bridging and icicles. Provide rigid support for the board. SS19/SS19T MICRO SWITCH recommends an infrared reflow process with peak temperatures not to exceed 190 - 200°C (374 - 392°F) for 10 seconds maximum. Keep exposure to high temperatures minimal. CLEANING Clean appropriately in accordance with applicable safety procedures. MICRO SWITCH recommends manual cleaning. BLOCK DIAGRAM TRANSFER CHARACTERISTICS
SS49/SS19 Series Issue 2 PK 88740
2 Honeywell • MICRO SWITCH Sensing and Control For application help: call 1-800-537-6945
TYPICAL OUTPUT CHARACTERISTICS
SS49/SS19 Series ISSUE 2 PK 88740 For application help: call 1-800-537-6945 Honeywell • MICRO SWITCH Sensing and Control 3 MOUNTING DIMENSIONS (for reference only) SS49 SERIES SS19 SERIES
SS49/SS19 Series Issue 2 PK 88740 MICRO SWITCH Honeywell Inc.
11 West Spring Street
Freeport, Illinois 61032 Printed with Soy Ink on 50% Recycled Paper PK 88740-2-EN IL50 GLO 298 Printed in USA WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact a nearby sales office. Or call: 1-800-537-6945 USA 1-800-737-3360 Canada 1-815-235-6847 International FAX 1-815-235-6545 USA INTERNET http://www.honeywell.com/sensing/ info@micro.honeywell.com Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance, personally and through our literature, it is up to the customer to determine the suitability of the product in the application.