SS05M JUXING | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
- 2 in 1,separate
- Ideal for automated placement
- Glass passivated chip junctions
- Low leakage current
- Applicable to for energy conservation electronic Ballasts fluorescent lamps Mechanical Date
- Case: JESD30E PSOJ-4 molded plastic body over glass passivated chip Major Ratings and Characteristics
- Terminals: Solder plated, solderable per J-STD-002 and JESD22-B102
- Polarity: Polarity symbols marked on body
- Weight: 0.046g Maximum Ratings & Thermal Characteristics (TA = 25 ° C unless otherwise noted) Electrical Characteristics (TA = 25 ° C unless otherwise noted) Note 2: Pulse test: 300 μs pulse width, 1 % duty cycle Note 3: Pulse test: Pulse width 40 ms 50 μAReverse current IF=0.5A(2) ,TA=66℃Instantaneous forward voltage IR - - Type VR=VDC (3) TA=25℃ TA=125℃ VF V A ℃/ W ℃/ W 101 - 0.98 1.10 Min UNIT V V V A Max UNITItems Test conditions IFSM RθJA RθJL Thermal resistance from junction to ambient (1) Thermal resistance from junction to lead (1) Symbol 0.5 A 1000 V 20 A 1.1 V 150 ° C –55 to +150 °C IF(AV) VRRM IFSM VF Tj max. TSTG Items SS05M Maximum repetitive peak reverse voltage 1000 Maximum RMS voltage 700 Symbol VRRM VRMS Maximum DC blocking voltage 1000 Maximum average forward rectified current 0.5 Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load 20 VDC IF(AV) TRR copyright -A 2013-00-130110 - 1 - http://www.trr-jx.com
Surface Mount Twin Standard Rectifiers Marking And Structure Soldering Pad Recommended connection the devices used in the bridge rectifier circuit TRR copyright -A 2013-00-130110 - 2 - http://www.trr-jx.com
Surface Mount Twin Standard Rectifiers Characteristic Curves (TA=25 ℃ unless otherwise noted) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0 30 60 90 120 150 Average Forward Current(A) Ambient Temperature (℃) Fig.1 Forward Current Derating Curve 8.3ms Single Half Sine-Wave (JEDEC Method) Mounted On FR-4 P.C.B With 0.1X0.1"(2.5x2.5mm) Copper Pad Areas 0.01 0.1 Instantaneous Forward current(A) Instantaneous Forward Voltage(V) Fig.3 Typical Instantaneous Forward Characteristics Tj=25℃ Pulse Width = 300μs Tj=25℃ Tj=125℃ 0.01 0.1 0 20 40 60 80 100 Instantaneous Reverse Leakage Current(μA) Percent or Rated Peak Reverse Voltage(%) Fig.4 Typical Reverse Leakage Characteristics 1 10 100 Peak Forward Surge Current(A) Number of Cycles at 60Hz Fig.2 Maximum Non-Repetitive Peak Forward Surge Current TRR copyright -A 2013-00-130110 - 3 - http://www.trr-jx.com
Surface Mount Twin Standard Rectifiers Package Outline Notice
- Product is intended for use in general electronics applications.
- Product should be worked less than the ratings; if exceeded, may cause permanent damage.or introduce latent failure mechanisms.
- The absolute maximum ratings are rated values and must not be exceeded during operation. The following are the general derating methods you design a circuit with a device. IF(AV) : We recommend that the worst case current be no greater than 80% . IFSM : This rating specifies the non-repetitive peak current. This is only applied for an abnormal operation, which the general during the lifespan of the device. TJ : Derate this rating when using a device in order to ensure high reliability. We recommend that the device be used at at a TJ of below 125° C. a TJ of below 125° C.
- TRR is registered trademark of Rising-sun Technology. Rising-sun Technology reserves the right to make changes to any product in this specification to improve reliability,functional characteristics,or design without notice.
- Rising-sun Technology does not assure any liability arising out of the applications or any product described in this specification.
- Rising-sun Technology advises customers to obtain the latest version of the device information before placing orders to verify that the required information is current. TRR copyright -A 2013-00-130110 - 4 - http://www.trr-jx.com