SRX03-APD OPLINK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Features

R4.2008.04.30

Oplink Communications, Inc. Interface Circuit Pin Assignments (Top View) SIGNAL DETECT+ VPD OUTPUT SIGNAL DETECT- Note 1: This resistor is for the PECL option only. It should be omitted for TTL option. Note 2: Resistor values are in Ω, capacitor values are in µF. 1µH coil or ferrite inductor SRX +5V 510 (Note 1) 510 (Note 1) 0 10 1 130 1,24 4,11,12,13 14,15,19 1 0 . 01 0 . 0 7,18,20 82 8216 DATA+ DATA- 130 All CASE pins should be grounded N/C: No internal connection CASE N/C VPD OUT GND VPM+ VPM- VCC DATA+ DATA- N/C GND GND CASE N/C N/C N/C V CC VCC SIGNAL DETECT - SIGNAL DETECT + GND GND GND GND Receiver Performance Characteristics (Over Operating Case Temperature, VCC = 4.75 to 5.25V) SRX03-APD Parameter Symbol Minimum Typical Maximum Units Operating Data Rate 1 B - 156 - Mb/s Receiver Sensitivity (10-10 BER) 2 Temperature Option “I” Pmin - 41.0 - 43.0 - dBm Temperature Option “H” - 42.0 - 44.0 - Maximum Input Optical Power (10-10 BER) 2 Pmax - 8.0 - 3.0 - dBm Signal Detect Thresholds Increasing Light Input Psd+ - - - 42.0 dBm Decreasing Light Input Psd- - 55.0 - - Signal Detect Hysteresis - - 0.5 - dB Wavelength of Operation λ 1100 - 1600 nm Optical Power Monitor Differential Voltage (at 25°C) VPM - 30 - mV/µW 1 Data rate ranges from 10Mb/s to 200Mb/s. However, some degradation may be incurred in overall performance. 2 Specified in average optical input power and measured at 1310nm wavelength with 223-1 PRBS at 156Mb/s. Receiver Electrical Interface (Over Operating Case Temperature, VCC = 4.75 to 5.25V) Parameter Symbol Minimum Typical Maximum Units Supply Voltage VCC 4.75 5.0 5.25 V Supply Current ICC - 120 180 mA DATA Output HIGH Voltage 1 VOH VCC - 1.150 - VCC - 0.880 V DATA Output LOW Voltage 1 VOL VCC - 1.830 - VCC - 1.555 V SIGNAL DETECT HIGH Voltage (PECL option) 1 VOH VCC - 1.150 - VCC - 0.880 V SIGNAL DETECT LOW Voltage (PECL option) 1 VOL VCC - 1.830 - VCC - 1.555 V SIGNAL DETECT HIGH Voltage (TTL option) VOH 2.7 - VCC V SIGNAL DETECT LOW Voltage (TTL option) VOL 0 - 0.5 V VPD Output Voltage (maximum current 3mA) VPD - 90 - 60 - 20 V 1 With termination of 50Ω to VCC - 2V. 2 R4.2008.04.30 All parameters guaranteed only at typical data rate

46335 Landing Parkway Fremont, CA 94538-6407 T el: (510) 933-7200 Fax: (510) 933-7300 Email: Sales@Oplink.com Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Commu- nications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. © 2008, Oplink Communications, Inc. Application Notes The receiver converts the incident optical power to a photocurrent via a high performance avalanche photodiode (APD). The photocurrent can be monitored via the differential voltage across the two VPM+ and VPM- output pins. It is important to note that the common mode voltage (i.e. DC voltages at PM+ and VPM-) is high (-60V typical). The APD bias voltage is temperature compensated to ensure stable operation over the entire operating temperature range. The APD bias voltage is also available as an output via the VPD output. The maximum current that this output can source is 1mA. The signal detect circuit monitors the level of the incoming optical signal and generates a logic LOW signal when an insufficient photocurrent is produced. Both differential DATA+ and DATA- outputs (also SIGNAL DETECT+ and SIGNAL DETECT- if the PECL option is chosen) are open emitter PECL levels requiring termination (50Ω to VCC - 2V or 510Ω to GND is recommended). Both differential outputs should be terminated in the same manner, even if only one is used. If the TTL option is chosen for the SIGNAL DETECT outputs, no termination resistor should be used. The power supply line should be wellfiltered. The power supply should be bypassed by 0.01 or 0.1μF ceramic chip placed as close to the receiver module as possible. Related Transmitter & Receiver Modules STX-03: OC-3/STM-1 Transmitter (multi-sourced 20-pin DIP) SRX-03: OC-3/STM-1 Receiver without Clock Recovery, ECL SIGNAL DETECT (multi-sourced 20-pin DIP) SRC-03: OC-3/STM-1 Receiver with Clock Recovery (multi-sourced 20-pin DIP) SRC-03-S: OC-3/STM-1 Receiver with Clock Recovery (24-pin DIP , compatible with Sumitomo SDT8701-RD) The pigtail length from the package edge is 1.0 meter typical.

Ordering Information

R4. 2008.04.303 SRX 0 0 03 X R 28 0 Supply Voltage RX only 5V= 8 T emperature Range Connector T ype & Option Pigtail FC, SD-TTL= PA Pigtail ST, SD-TTL= PB Pigtail SC, SD-TTL= P5 Pigtail FC, SD-PECL= PC Pigtail ST, SD-PECL= PD Pigtail SC, SD-PECL= P4 -40 ~85˚C= I 0~70˚C= H APD VPM- VPM+ VPD OUT APD Bias 220Ω 10kΩ 10kΩ Supply Package Outline Dimensions in inches [mm] Default tolerances: Receivers Wavelength Range 1100~1600nm APD