DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

knowles.com Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles 1 The SPW0442HR5H-1 is a miniature, high-performance, low power, top port silicon microphone. Using Knowles’ proven high-performance SiSonicTM MEMS technology, the SPW0442HR5H-1 consists of an acoustic sensor, a low noise input buffer, and an output amplifier. These devices are suitable for applications such as cellphones, smart phones, laptop computers, sensors, digital still cameras, portable music recorders, and other portable electronic devices where excellent wideband audio performance and RF immunity are required. Product Features

  • Matched Sensitivity
  • Small Package
  • Low Current
  • MaxRF Protection
  • Top Ported Design
  • Ultra-Stable Performance
  • Standard SMD Reflow
  • Omnidirectional Typical Applications
  • Portable electronics
  • Cellphones
  • Laptop Computers
  • Tablets
  • Digital Still Cameras
  • Portable Music Recorders SPW0442HR5H-1 Rev E Datasheet Precision Top Port SiSonicTM Microphone SPW0442HR5H-1

knowles.com Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles 2 GROUND VDD VDD OUTPUT External Gain = -RF/RS (Set By User) VREF RF RS Dashed Section Represents SiSonicTM Microphone .1µf Absolute Maximum Ratings Table 1: Absolute Maximum Ratings Parameter Absolute Maximum Rating Units Vdd to Ground -0.5, +5.0 V OUTPUT to Ground -0.3, Vdd+0.3 V Input Current to any pin ±5 mA Temperature -40 to +100 ºC Stresses exceeding these “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only. Functional operation at these or any other conditions beyond those indicated under “Acoustic & Electrical Specifications” is not implied. Exposure beyond those indicated under “Acoustic & Electrical Specifications” for extended periods may affect device reliability. Acoustic & Electrical Specifications Table 2: Normal Mode Microphone Specifications Test Conditi ons: 23 ±2°C, 55±20% R.H., Vdd(min) < Vdd < Vdd(max) , no load, unless otherwise indicated Parameter Symbol Conditions Min Typ Max Units Supply Voltage Vdd 1.5 - 3.6 V Supply Current Idd Vdd = 1.8V - 130 165 µA Supply Current1 Idd Vdd = 3.6V - 150 185 µA Sensitivity1 S 94 dB SPL @ 1 kHz -43 -42 -41 dBV/Pa Signal to Noise Ratio SNR 94 dB SPL @ 1 kHz, A-weighted - 59 - dB(A) Total Harmonic Distortion THD 94 dB SPL @ 1 kHz, S = Typ, Rload > 3kΩ - 0.15 0.25 % Acoustic Overload Point AOP 10% THD @ 1 kHz, S = Typ, Vdd = 3.6V, Rload > 3kΩ 128 130 - dB SPL Power Supply Rejection Ratio PSRR 200 mVpp sine wave 50-20kHz @1kHz, Vdd = 1.8V - 66 - dB Power Supply Rejection PSR 100 mVpp square wave - -100 - dBV(A) DC Output Vdd = 1.5V - 1.3 - V Output Impedance Zout @ 1 kHz - - 500 Ω Directivity Omnidirectional Polarity Increasing sound pressure Decreasing output voltage 1 100% tested. Application Notes Figure 1: Typical Application Circuit Notes: All Ground pins must be connected to ground. Capacitors near the microphone should not contain Class 2 dielectrics due to their piezoelectric effects. Detailed information on acoustic, mechanical, and system integration can be found in the latest SiSonicTM Design Guide application note.

knowles.com Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles 4 Mechanical Specifications Item Dimension Tolerance Length (L) 3.10 ±0.10 Width (W) 2.50 ±0.10 Height (H) 1.00 ±0.10 Acoustic Port (AP) Ø0.45 ±0.05 PCB Thickness (T) 0.28 +0.05 -0.03 Pin # Pin Name Type Description

1 OUTPUT Signal Output Signal

2 GROUND Power Ground

3 GROUND Power Ground

4 Vdd Power Power Supply

Example Solder Stencil Pattern Notes: Pick Area only extends to 0.25 mm of any edge or hole unless otherwise specified. Dimensions are in millimeters unless otherwise specified. Tolerance is ±0.15mm unless otherwise specified Detailed information on AP size considerations can be found in the latest SiSonicTM Design Guide application note. Further optimizations based on application should be performed.

knowles.com Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles 5 Packaging & Marking Detail Model Number Suffix Reel Diameter Quantity Per Reel SPW0442HR5H-1 -7 13” 5,700 Alpha Character A: “S”: Knowles SiSonic™ Production “E”: Knowles Engineering Samples “P”: Knowles Prototype Samples “JIN Number”: Unique Job Identification Number For product traceability Notes: Dimensions are in millimeters unless otherwise specified. Vacuum pickup only in the pick area indicated in Mechanical Specifications. Tape & reel per EIA-481 Rev C. Labels applied directly to reel and external package. Shelf life: Twelve (12) months when devices are to be stored in factory supplied, unopened ESD moisture sensitive bag under maximum environmental conditions of 30°C, 70% R.H. Pin 1

knowles.com Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles 6 Recommended Reflow Profile Profile Feature Pb-Free Average Ramp-up rate (TSMAX to TP) 3°C/second max. Preheat

  • Temperature Min (TSMIN)
  • Temperature Max (TSMAX)
  • Time (TSMIN to TSMAX) (tS) 150°C 200°C 60-180 seconds Time maintained above:
  • Temperature (TL)
  • Time (tL) 217°C 60-150 seconds Peak Temperature (TP) 260°C Time within 5°C of actual Peak Temperature (tP) 20-40 seconds Ramp-down rate (TP to TSMAX) 6°C/second max Time 25°C to Peak Temperature 8 minutes max Notes: Based on IPC/JDEC J-STD-020 Revision C. All temperatures refer to topside of the package, measured on the package body surface Additional Notes (A) MSL (moisture sensitivity level) Class 1. (B) Maximum of 3 reflow cycles is recommended. (C) In order to minimize device damage:
  • Do not board wash or clean after the reflow process.
  • Do not brush board with or without solvents after the reflow process.
  • Do not directly expose to ultrasonic processing, welding, or cleaning.
  • Do not insert any object in port hole of device at any time.
  • Do not apply over 30 psi of air pressure into the port hole.
  • Do not pull a vacuum over port hole of the microphone.
  • Do not apply a vacuum when repacking into sealed bags at a rate faster than 0.5 atm/sec. Time 25°C to Peak Ramp-down Ramp-up TSMIN TSMAX TL TP tL tP tS Preheat Time 25°C

knowles.com Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles 7 Materials Statement Meets the requirements of the European RoHS directive 2011/65/EC as amended. Meets the requirements of the industry standard IEC 61249-2-21:2003 for halogenated substances and Knowles Green Materials Standards Policy section on Halogen-Free. Product is Beryllium Free according to limits specified on the Knowles Hazardous Material List (HSL for Products). Ozone depleting substances are not used in the product or the processes used to make the product, including compounds listed in Annex A, B, and C of the “Montreal Protocol on Substances That Deplete the Ozone Layer.” Reliability Specifications Test Description Thermal Shock 100 cycles of air-air thermal shock from -40°C to +125°C with 15 minute soaks (IEC 68-2-4) High Temperature Storage +105°C environment for 1,000 hours (IEC 68-2-2 Test Ba) Low Temperature Storage -40°C environment for 1,000 hours (IEC 68-2-1 Test Aa) High Temperature Bias +105°C environment while under bias for 1,000 hours (IEC 68-2-2 Test Ba) Low Temperature Bias -40°C environment while under bias for 1,000 hours (IEC 68-2-1 Test Aa) Temperature/Humidity Bias +85°C/85% R.H. environment while under bias for 1,000 hours (JESD22-A101A-B) Vibration 12 minutes in each X, Y, Z axis from 20 to 2,000 Hz with peak acceleration of 20 G (MIL 883E, Method 2007.2,A) ESD-HBM 3 discharges of ±2kV direct contact to I/O pins (MIL 883E, Method 3015.7) ESD-HBM (LID/GND) 3 discharges of ±8kV direct contact to lid while unit is grounded (MIL 883E, Method 3015.7) ESD-MM 3 discharges of ±200V direct contact to IO pins (ESD STM5.2) Reflow 5 reflow cycles with peak temperature of +260°C Mechanical Shock 3 pulses of 10,000 G in each of the ±X, ±Y, and ±Z directions (IEC 68-2-27 Test Ea) Notes: After 3 reflow cycles, the sensitivity of the microphones shall not deviate more than 1 dB from its initial value.

knowles.com Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles 8 Specification Revisions Revision Specification Changes Date A Initial Release (ECR 15-421) 10/8/2015 B Updated Tolerances, landing pattern, and stencil (ECR 15-489) 11/17/2015 C Added max Idd@1.8V; corrected PCB thickness and tolerance. (ECR 16-570) 1/6/2016 D Updated AOP, added packaging resistivity, clarify T&R compliance, update Materials Statement (ECR 16-593) 1/26/2016 E Updated carrier tape (ECR 17-1385) 1/12/2017 Information contained herein is subject to change without notice. It may be used by a party at their own discretion and risk. We do not guarantee any results or assume any liability in connection with its use. This publication is not to be taken as a license to operate under any existing patents. Model/Reference Number: Datasheet SPW0442HR5H-1 Rev E © Copyright 2017 Knowles Phone: (630) 250-5100 Fax: (630) 250-0575 sales@knowles.com Knowles

1151 Maplewood Drive

Itasca, Illinois 60143