SPT SENSATA | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 2
Technical content
sensata.com/newall Copyright © 2023 Sensata Technologies Inc. |SPT ENCODER INTERFACE MODULES Model SPT (Part No. 600-83580) 5-28Vin, 5V TTL out (Line driver 26C31) Power requirements Voltage 5V to 28V ± 5% Ouput Power 1.5W max (<150mA at 5V) Output signals Differential quadrature signals A, B, A-, B- Phase angle A to B 90º Frequency range 0-2MHz, equivalent to 2ms-1 with 1µm resolution Reference mark Signal Differential Reference RM, RM- As per EncoderPeriodic or Single Point Enclosure Material Aluminium extrusion Sealing IP54 Temperature Operation 0 to 55ºC Storage -20 to 85ºC SPECIFICATIONS 9D Connector Pin No. Module (female) RS422 Module (male) Vout = Vin or Open Collector
1 N/C N/C
2 A A
4 B B
7 5V supply out 5 5-28V supply in
8 RM RM
This power management interface module enables a 5V SHG-TT/TS or MHG-TT linear encoder to operate from a 5-28V supply. Output levels remain at TTL 5V quadrature levels.
Rev.12/27/2023 Page 2 CONTACT US Copyright © 2023 Sensata Technologies, Inc. Datasheets provided by Sensata Technologies, Inc., its subsidiaries and/or affiliates (“Sensata”) are solely intended to assist third parties (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, valuation, and judgment in designing Buyer’s systems and products. Sensata datasheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular datasheet. Sensata may make corrections, enhancements, improvements, and other changes to its datasheets or components without notice. Buyers are authorized to use Sensata datasheets with the Sensata component(s) identified in each particular datasheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATASHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATASHEETS OR USE OF THE DATASHEETS, EXPRESS, IMPLIED, OR STATUTORY , INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY , FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATASHEETS OR USE THEREOF. All products are sold subject to Sensata’s terms and conditions of sale supplied at www.sensata.com. SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY , AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA. Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USA Americas Newall Electronics Inc.
1803 OBrien Rd
Columbus, OH 43228 Tel: +1 614 771 0213 sales@newall.com newall.com Rest of World: Newall Measurement Systems, Ltd. Business Park, Unit 1 Wharf Way Glen Parva, Leicester LE2 9UT United Kingdom Tel: +44 (0) 116 264 2730 sales@newall.co.uk newall.co.uk sensata.com/newall DIMENSIONS INSTALLATION The module is to be situated between the encoder and the control system and connected as per the above pin-out. Care must be taken to ensure the location of the module is such that it is not exposed to environmental conditions beyond its IP rating. Ensure that the connection locking is secure. NOTE: Newall Measurement Systems Ltd. reserves the right to change the specification without notice. 023-81050/2 UK N SPT ENCODER INTERFACE MODULES DATASHEET Model SPT (Part No. 600-83580) 5-28Vin, 5V TTL out (Line driver 26C31) Power requirements Voltage 5V to 28V ± 5% Ouput power 1.5W max (<150mA at 5V) Output signals Differential quadrature signals A, B, A, B Phase angle A to B 90º Frequency range 0-2MHz, equivalent to 2ms-1 with 1μm resolution Reference mark Differential Reference RM & RM As per Encoder Signal Periodic or Single Point Enclosure Material Aluminium extrusion Sealing IP54 Temperature Operation 0 to 55ºC Storage -20 to 85ºC Connection Details Dimensions ANSI/ESD S8.1-2001 16mm / 0.63in 103mm / 4.06in 33mm / 1.30in Newall TT or TS Encoder Control Installation The module is to be situated between the encoder and the control system and connected as per the above pin-out. Care must be ta ken to ensure the location of the module is such that it is not exposed to environmental conditions beyond its IP rating. Ensure tha t the con- nection locking is secure. Introduction This power management interface module enables a 5V SHG-TT/TS or MHG-TT linear encoder to operate from a 5-28V supply. Output levels remain at RS422 5V quadrature levels. 9D Connector Pin No Module (Female) RS422 (Encoder) Module (Male) RS422 (Control) 7 5V supply out 5-28V supply in NOTE: Newall Measurement Systems Ltd. reserves the right to change the specification without notice. 023-81050/2 UK N SPT ENCODER INTERFACE MODULES DATASHEET Model SPT (Part No. 600-83580) 5-28Vin, 5V TTL out (Line driver 26C31) Power requirements Voltage 5V to 28V ± 5% Ouput power 1.5W max (<150mA at 5V) Output signals Differential quadrature signals A, B, A, B Phase angle A to B 90º Frequency range 0-2MHz, equivalent to 2ms-1 with 1μm resolution Reference mark Differential Reference RM & RM As per Encoder Signal Periodic or Single Point Enclosure Material Aluminium extrusion Sealing IP54 Temperature Operation 0 to 55ºC Storage -20 to 85ºC Connection Details Dimensions ANSI/ESD S8.1-2001 16mm / 0.63in 103mm / 4.06in 33mm / 1.30in Newall TT or TS Encoder Control Installation The module is to be situated between the encoder and the control system and connected as per the above pin-out. Care must be ta ken to ensure the location of the module is such that it is not exposed to environmental conditions beyond its IP rating. Ensure tha t the con- nection locking is secure. Introduction This power management interface module enables a 5V SHG-TT/TS or MHG-TT linear encoder to operate from a 5-28V supply. Output levels remain at RS422 5V quadrature levels. 9D Connector Pin No Module (Female) RS422 (Encoder) Module (Male) RS422 (Control) 7 5V supply out 5-28V supply in