SPSPFE3-07 BEL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 17

Technical content

SPSPFE3-HVDC power shelf solutions provide rectification, system management, and power distribution, while maintaining high reliability and offering flexibility for future expansion. The power shelf can be configured with up to six hot -swap capable PFE3000-12-069RA AC/DC -DC power supplies that convert High Voltage DC Bus power into a mai n output of 12 VDC for powering intermediate bus architectures (IBA) in high performance and reliability servers, routers, and network switches. The shelf is compatible with the Open Compute Rack Design. The shelf has an optional slot for Network Attached Controller for providing control functions and monitoring through a 10/100 MB base Ethernet port and can be connected directly to the data center management network.

  • Two separate DC inputs, one DC inlet powers 3 power modules.
  • Modules are hot-swap capable.
  • Modules support I2C communication interface for control, programming and monitoring with Power Management Bus protocol.
  • Modules implement the following protections: Overtemperature, output overvoltage and output overcurrent.
  • RoHS Compliant.
  • Available for OCP V2 bus-bar style connection.
  • High Performance Servers
  • Routers
  • Switches

SPSPFE3-07, SPSPFE3-12, SPSPFE3-13 tech.support@psbel.com 1. GENERAL BEL POWER SHELF REFERENCE TABLE INPUT AC ( Y ) 277/480 VAC AC ( Y ) 240/415 VAC AC ( Δ )

208 VAC

AC (1-Phase) 3x 230 VAC - 48 VDC +380 VDC OUTPUT +12 VDC Triple Busbar Straight SPSPFE3-05G SPSPFE3-15* SPSPFE3-09 - SPSPFF3-03* SPSPFE3-13* Single Busbar Straight SPSPFE3-06G SPSPFE3-16* SPSPFE3-10 SPSTET4-02 SPSPFF3-02* SPSPFE3-12* Single Busbar Offset 1 SPSPFE3-08 SPSPFE3-14* SPSPFE3-11 - SPSPFF3-01 SPSPFE3-07 +48 VDC Single Busbar Offset Short 2 SPSTET4-01 SPSTET4-11 SPSTET4-03* - N/A SPSTET4-04* Single Busbar Offset Long 1 SPSTET4-07 SPSTET4-12 - - N/A - Single Busbar Straight Long SPSTET4-09 SPSTET4-13 - - N/A - Triple Busbar Straight Long SPSTET4-08 SPSTET4-14 SPSTET4-17* - N/A - +380 VDC Connector Type SPSTET4-05* - SPSTET4-06* - - N/A 1 Mates with V2 * Available on request requiring short design cycle.

2 Mates with V2 shallow rack

NOTE: Other datasheets contain alternative shelf configurations, check factory for availability. 2. ORDERING INFORMATION MODEL INPUT AND OUTPUT CONFIGURATION SPSPFE3-07 Two 240 to 380 VDC inputs (nominal 380 VDC) 1 set of output blade for +12 VDC output, Offset Bus bar SPSPFE3-07C Two 240 to 380 VDC inputs (nominal 380 VDC) 1 set of output blade for +12 VDC output, Offset Bus bar Network Attached Controller included SPSPFE3-12 Two 240 to 380 VDC inputs (nominal 380 VDC) 1 set of output blade for +12 VDC output, Straight Bus bar SPSPFE3-12C Two 240 to 380 VDC inputs (nominal 380 VDC) 1 set of output blade for +12 VDC output, Straight Bus bar Network Attached Controller included SPSPFE3-13 Two 240 to 380 VDC inputs (nominal 380 VDC) 3 sets of output blades for +12 VDC output (each set of blades has max.585 A) SPSPFE3-13C Two 240 to 380 VDC inputs (nominal 380 VDC) 3 sets of output blades for +12 VDC output (each set of blades has max.585 A) Network Attached Controller included

SPSPFE3-07, SPSPFE3-12, SPSPFE3-13 3 Asia-Pacific +86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2021 Bel Power Solutions & Protection BCD.00919_A 3. TECHNICAL DATA PARAMETER DESCRIPTION/CONDITION Input Two 240 to 380 VDC inputs (nominal 380 VDC) DC Inlet Configuration 3 power modules are powered from one DC inlet. 2 DC inlets (Input1, Input2) Redundant Configuration 3+3 or 5+1 configuration Rated Power 1 8700 W (3+3 configuration) 1 Rated Power 2 14400 W (5+1 configuration) 1 Output Connection SPSPFE3-07: 1 set of output blade for +12 VDC output, Offset Bus bar SPSPFE3-12: 1 set of output blade for +12 VDC output, Straight Bus bar SPSPFE3-13: 3 sets of output blades for +12 VDC output (each set of blades has max.585 A) Standby Output 60 W (Standby output 12 V / 5 A) Communication I2C Power Management Bus NAC2006-01 Network Attached Controller: Ethernet – SNMPv3 / HTTP 4. SAFETY WARNING The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies Be l Power Solutions Inc. from all claims arising from the handling or use of the goods. Persons handling the product(s) must have electronics training and observe good engineering practice standards. CAUTION: Multiple power source. Disconnect all power cords before servicing. 5. REFERENCE DOCUMENTS DOCUMENT NUMBER DESCRIPTION BCD.00297 PFE3000-12-069RA Datasheet BCA.00070 PFE3000-12-069RA Power Management Bus Communication Manual BCM.00177 Installation Instruction PFE3000-12-069RA BCD.00926 NAC2006-01 Datasheet BCA.00178 SPSPFE3-0XG Communication Manual BCM.00474 Installation Instruction SPSPFE3-07 PCA9547PW PCA9547PW Datasheet from NXP The SPSPFE3-HVDC Power Shelf is a 1 OU height power shelf. It can be configured with up to six hot -swap capable PFE3000-12- 069RA AC/DC -DC power supplies that convert High Voltage DC bus mains power into a main output of 12 VDC for powering intermediate bus architectures (IBA) in high performance and reliability servers, routers, and network switches. The I2C communication is routed through an I2C Multiplexer (NXP PCA9547PW). PSU Modules support I 2C communication interface for control, programming and monitoring with the Power Management Bus protocol. The shelf can be operated by a network attached controller (NAC) for providing monitoring and control functions through a 10/100 MB base Ethernet port and can be connected directly to the data center management network. It is hot-pluggable and supplied via the 12 V standby provided by the power supplies in the shelf. The controller can be configured thr ough a web interface; the monitoring and control functions are accessed through SNMPv3. 1 Rated Power is reduced as per current share accuracy characteristic. See PFE3000-12-069RA Datasheet.

Figure 1. SPSPFE3-HVDC Block Diagram

380 Vdc

SPSPFE3-07, SPSPFE3-12, SPSPFE3-13 5 Asia-Pacific +86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2021 Bel Power Solutions & Protection BCD.00919_A PARAMETER DESCRIPTION / CONDITION MIN NOM MAX UNIT Input Connector (J106, J107) DC Nominal Input Voltage 380 VDC DC Nominal Voltage Ranges Nominal Range 240 380 VDC DC Input Voltage Ranges Functional Range 192 400 VDC Max Input Current per DC inlets (Input1, Input2) 33 ADC PARAMETER DESCRIPTION / CONDITION MIN NOM MAX UNIT Main Output V1 (Output Bus Bar) Nominal Output Voltage 12.3 VDC Voltage Regulation -5 +5 % Vout nom Nominal Output Power 1 3+3 configuration, Ta < 45°C 8700 W Derated Output Power 1 3+3 configuration, Ta = 55 °C 2 6525 W Nominal Output Power 2 5+1 configuration, Ta < 45°C 14400 W Derated Output Power 2 5+1 configuration, Ta = 55 °C 3 10800 W Nominal Output Current 1 3+3 configuration, Ta < 45°C 707 ADC Derated Output Current 1 3+3 configuration, Ta = 55 °C 3 530 ADC Nominal Output Current 2 5+1 configuration, Ta < 45°C 1171 ADC Derated Output Current 2 5+1 configuration, Ta = 55 °C 3 878 ADC Standby Output VSB (J23) Output Voltage 12 VDC Voltage Regulation -5 +5 % Vout nom Output Power 60 W Output Current 5 ADC

2 Linear derating at Ta > 45°C is based per module, see PFE3000-12-069RA datasheet

3 ISHARE V1 Current share bus

4 PWOK_L Power OK signal output: active-low

5 INOK_L Input OK signal: active-low

6 SMB_ALERT_L SMB Alert signal output: active-low

7 PSON_SHELF_L Power Shelf on input: active-low

8 SGND Signal ground

Table 1. I2C Interface and Signal Connector (RJ45) Pin Out

3 Limit doesn’t include effects of main output capacitive discharge

4 External Pull-up resistor should be 2 – 5kΩ to ensure SMBUS compliant signal rise times

OR already in the shelf. Sink current must not exceed 4 mA on each of these signals. output signal. INOK_L is low when there is at least one module supplied with correct input voltage. voltage for the PWOK_L, INOK_L and SMB_ALERT_L signals. The Power Shelf V1 output is capable to be operated in redundant mode by interconnecting the ISHARE on J20. Please consult BPS Technical Representative for details.

NOTE: Communication Manual of shelf, see document BCA.00178. Table 2. DIP Switch Setting (SW1) Multiplexer. The I2C MUX Control Register needs to be configured so that the I2C frames are routed to the correct PSU Module. Refer to the I2C MUX datasheet for additional information. see document BCA.00178 for further information and the table below. a web interface; the monitoring and control functions are accessed through SNMP. See BCD.00926 for NAC2006-01 Datasheet.

5 The order of the criteria in the table corresponds to the testing precedence in the controller. or off, while LED number two is bi-colored: green and yellow and indicates DC power presence or fault situations. boot loading of the PSU Modules. Figure 2. Connection The USB interface is NOT galvanically isolated and referenced to the +12V_GND / SGND lines. Preferably, use a battery operated laptop to avoid earth loop issues. of a USB isolator is highly recommended in such a case. +12VSB output is capable of delivering 5A. The output is protected by a PTC (16R900GF from Littelfuse).

SPSPFE3-07, SPSPFE3-12, SPSPFE3-13 9 Asia-Pacific +86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2021 Bel Power Solutions & Protection BCD.00919_A PARAMETER DESCRIPTION / CONDITION CRITERION Agency Approvals UL / CSA 60950-1 IEC / EN 60950-1 Approved UL / CSA 62368-1 IEC / EN 62368-1 Approval pending Insulation Input (DCIN+ / DCIN-) to case (PE) Input (DCIN+ / DCIN-) to output Output to case (PE) Basic Reinforced Functional Creepage / Clearance (dC) Input (DCIN+ / DCIN-) to protective earth (PE) Primary to secondary Electrical Strength Test Input to case Input to output (tested by manufacturer only) Min. 2121 VDC Min. 4242 VDC Conducted Emission EN55022 / CISPR 22: 0.15 … 30 MHz, QP and AVG Class A Radiated Emission EN55022 / CISPR 22: 30 MHz … 1 GHz, QP Class A Harmonic Emissions (per module) IEC61000-3-2, Vin = TBD VDC, 100% Load (per module) TBD Acoustical Noise Sound power statistical declaration (ISO 9296, ISO 7779, IS9295) @ 50% load 60 dBA ESD Contact Discharge IEC / EN 61000-4-2, ±8 kV, 25+25 discharges per test point (metallic case, LEDs, connector body) A ESD Air Discharge IEC / EN 61000-4-2, ±15 kV, 25+25 discharges per test point (non-metallic user accessible surfaces) A Radiated Electromagnetic Field IEC / EN 61000-4-3, 10 V/m, 1 kHz/80% Amplitude Modulation, 1 µs Pulse Modulation, 10 kHz…2 GHz A Burst IEC / EN 61000-4-4, level 3 AC port ±2 kV, 1 minute DC port ±1 kV, 1 minute A Surge IEC / EN 61000-4-5 Line to earth: level 3, ±2 kV Line to line: level 2, ±1 kV A RF Conducted Immunity IEC/EN 61000-4-6, Level 3, 10 Vrms, CW, 0.1 … 80 MHz A Voltage Dips and Interruptions (per module) IEC/EN 61000-4-11 (per module) TBD PARAMETER DESCRIPTION / CONDITION MIN NOM MAX UNIT Operating Temperature @ full load, up to 4000 m: @ full load, up to 1800 m: @ 75% load, up to 1800 m: +35 +45 +55 Non-Operating Temperature -40 +70 °C Humidity Operating: @ at 40 °C, non-condensing Non-Operating: non-condensing 5 93 95 %RH Altitude Operating: Non-Operating: 4000 13000 m Shock Operating: 11 ms half-sine shocks in Z axis 10+ve, 10-ve Non-Operating: 11 ms half-sine shocks in Z axis 10+ve, 10-ve 5 30 g Vibration Operating: 0.2 grms random Non-Operating: 1 grms random 2 500 200 Hz Acoustic Noise Emissions @ normal operation, and 50% load sharing Fan speed 70 7000 dBA rpm Cooling When equipped with operating PSUs 50 Pa

SPSPFE3-07, SPSPFE3-12, SPSPFE3-13 tech.support@psbel.com PARAMETER SPSPFE3-HVDC Dimensions (W x H x D) 534.5 x 46.5x 650 mm (overall: 535 x 47 x 859.5 mm) Weight (Shelf only) 16 kg Weight (6 PSU installed) 32 kg DESCRIPTION REFERENCE DESIGNATOR TYPE MANUFACTURER MPN MATING PART MPN Input Connector J106, J107 HVDC Input ANDERSON POWER PRODUCTS SBS75XPRBLK-BK SBS75XBLK-BK Protective Earth 2x M6 PEM6 DESCRIPTION REFERENCE DESIGNATOR TYPE MANUFACTURER MPN MATING PART MPN USB I2C Connector J3 USB – B type Tyco 292304-1 I2C Interface and Signal Connector J20 RJ45 FCI Connectors 87180-088LF +12VSB output connector J23 Molex 39-30-0040 39-01-2045

6 Mating M6 Screw + Washer are delivered together with the shelf

Figure 13. SPSPFE3-13 Isometric View

SPSPFE3-07, SPSPFE3-12, SPSPFE3-13 17 Asia-Pacific +86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2021 Bel Power Solutions & Protection BCD.00919_A REV DESCRIPTION PRODUCT VERSION DATE AUTHOR

001 PRELIMINARY: Initial Draft V001 08-31-2017 GS

002 Update Mechanical View V001 10-05-2017 GS

003 DC input voltage align with PSU Module. V001 10.31.2017 GS 004 Update Datasheet part number for NAC2006-01. PMBus™ changed to Power Management Bus; a disclaimer added to the first page V001 02-28-2018 VS 005 Network Attached Controller is set to optional. Update Ordering Information. Removed Pending on Safety Agency Approvals V002 04-24-2018 GS 006 Disclaimer on the first was removed Power Management Bus needs to be fully spelled out every time it is used with no trademark symbols used V003 04-26-2019 VS 007 Enable Current Share Function of Shelf Pin 3 of Connector J20 used for ISHARE signal Add SPSPFE3-12 and SPSPFE3-13 Models V003 09-30-2019 GS A Release to A revision 04-29-2021 NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice.