SPSPFE3-02G | DigiCamel IC Datasheet

Online Datasheet

Read SPSPFE3-02G online.

SPSPFE3-0XG BEL | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 14

Technical content

© 2015 Bel Power Solutions, Inc. North America +1-866.513.2839 Asia-Pacific +86.755.29885888 Europe, Middle East +353 61 225 977 tech.support@psbel.com BCD.00575_001  Two 3-Phase inputs, one AC inlet powers 3 power modules.  Modules are hot-swap capable.  Modules support I2C communication interface for control, programming and monitoring with PMBus™ protocol.  Modules implement the following protections: Overtemperature, output overvoltage and output overcurrent.  RoHS Compliant. SPSPFE3-0XG power-shelf solutions provide rectification, system management, and power distribution, while maintaining high reliability and offering flexibility for future expansion. The power shelf can be configured with up to six hot-swap capable PFE3000-12-069RA AC/DC-DC power supplies that convert 3- phase AC mains power into a main output of

12 VDC for powering intermediate bus

architectures (IBA) in high performance and reliability servers, r outers, and network switches. The shelf can be mounted to a 19inch or 21inch rack system using adaptor mounting brackets and is compatible with the Open Compute rack design.

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 ITEM NUMBER INPUT CONFIGURATION SPSPFE3-02G 3-phase, 400/480 VAC line to line input with Neutral line SPSPFE3-03G 3-phase, 208 VAC line to line input without Neutral line SPSPFE3-0XG Input 3-phase, 400/480 VAC Line to Line input with Neutral 1 3-phase, 208 VAC Line to Line input without Neutral 2 AC Inlet Configuration 3 power modules are powered from one AC inlet Redundant Configuration 3+3 or 5+1 configuration Rated Power 1 8700W (3+3 configuration) 3 Rated Power 2 14400W (5+1 configuration) 3 Output Connection 3 set of output blades for +12V DC output Auxiliary Output 60W (Standby output 12V/5A) Communication I2C PMBus™, optional Ethernet capability 4 Notes: 1 Power modules are connected Line to Neutral. 2 Power modules are connected Line to Line. 3 Rated Power is reduced as per current share accuracy characteristic. See PFE3000-12-069RA Datasheet. 4 Contact factory. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies Bel Power Solutions Inc. from all claims arising from the handling or use of the goods. Persons handling the product(s) must have electronics training and observe good engineering practice standards. Caution: Multiple power source. Disconnect all power cords before servicing. DOCUMENT NUMBER DESCRIPTION BCD.00297 PFE3000-12-069RA Datasheet BCA.00070 PFE3000-12-069RA PMBus™ Communication Manual BCM.00177 Installation Instruction PFE3000-12-069RA BCA.00178 SPSPFE3-0XG Communication Manual BCM.00339 Installation Instruction SPSPFE3-0XG PCA9547PW PCA9547PW Datasheet from NXP The SPSPFE3-0XG Power Shelf is a 1U height power shelf. It can be configured with up to six hot-swap capable PFE3000-12- 069RA AC/DC-DC power supplies that convert standard AC mains power into a main output of 12 VDC for powering intermediate bus architectures (IBA) in high performance and reliability servers, routers, and network switches.

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 The I2C communication is routed thru an I2C Multiplexer (NXP PCA9547PW). PSU Modules support I2C communication interface for control, programming and monitoring with PMBus™ protocol. Sec Pri3 phase input 400/480Vac Sec Pri Sec Pri Sec Pri MUX PCA9547PW RJ45 PSU Bay 1 PSU Bay 2 PSU Bay 3 PSU Bay 4 +12V GND 3.3V LDO +12VSB SGND RESET SCL SDA SMB_ALERT_L ISHARE PWOK_L INOK_L Logic signals PWOK_L SMB_ALERT_L SC0/SD0 SC1/SD1 SC2/SD2 SC3/SD3 USB/ Ethernet Controller USB/Ethernet Connector USB/Ethernet communication and diagnostic DIP switches For Shelf Addressing PE N PE N Sec Pri PSU Bay 5 Sec Pri PSU Bay 6 3 phase input 400/480Vac PE N PE N SC4/SD4 SC5/SD5 ISHARE +12VSB_GND 2 31 3.3V RJ45 SGND RESET SCL SDA SMB_ALERT_L ISHARE PWOK_L INOK_L 3.3V INOK_L_P0 INOK_L_P1 INOK_L_P5 Figure 1 – SPSPFE3-02G Block Diagram

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 Sec Pri3 phase input 208Vac Sec Pri Sec Pri Sec Pri MUX PCA9547PW RJ45 PSU Bay 1 PSU Bay 2 PSU Bay 3 PSU Bay 4 +12V GND 3.3V LDO +12VSB SGND RESET SCL SDA SMB_ALERT_L ISHARE PWOK_L INOK_L Logic signals PWOK_L SMB_ALERT_L SC0/SD0 SC1/SD1 SC2/SD2 SC3/SD3 USB/ Ethernet Controller USB/Ethernet Connector USB/Ethernet communication and diagnostic DIP switches For Shelf Addressing PE PE Sec Pri PSU Bay 5 Sec Pri PSU Bay 6 3 phase input 208Vac PE PE SC4/SD4 SC5/SD5 ISHARE +12VSB_GND 2 31 3.3V RJ45 SGND RESET SCL SDA SMB_ALERT_L ISHARE PWOK_L INOK_L 3.3V INOK_L_P0 INOK_L_P1 INOK_L_P5 Figure 2 – SPSPFE3-03G Block Diagram

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 PARAMETER DESCRIPTION / CONDITION SPSPFE3-02G (L1, L2, L3, N, ) SPSPFE3-03G (L1, L2, L3, ) MIN NOM MAX MIN NOM MAX UNIT Input Connector (J106, J107) AC Nominal Input Voltage 400 / 480 208 VAC AC Input Voltage Ranges 346 480 200 240 VAC Max Input Current per line 17 30 Arms Input Frequency 47 50/60 63 47 50/60 63 Hz PARAMETER DESCRIPTION / CONDITION MIN NOM MAX UNIT Main Output V1 (Output Bus bar) Nominal Output Voltage 12.3 VDC Voltage Regulation -5 +5 % Vout nom Nominal Output Power 1 3+3 configuration, Ta < 45°C 8700 W Derated Output Power 1 3+3 configuration, Ta = 55 °C 5 6525 W Nominal Output Power 2 5+1 configuration, Ta < 45°C 14400 W Derated Output Power 2 5+1 configuration, Ta = 55 °C 5 10800 W Nominal Output Current 1 3+3 configuration, Ta < 45°C 707 ADC Derated Output Current 1 3+3 configuration, Ta = 55 °C 5 530 ADC Nominal Output Current 2 5+1 configuration, Ta < 45°C 1171 ADC Derated Output Current 2 5+1 configuration, Ta = 55 °C 5 878 ADC Note: 5 Linear derating at Ta > 45°C, is based per module, see PFE3000-12-069RA datasheet PARAMETER DESCRIPTION / CONDITION MIN NOM MAX UNIT Standy Output VSB Output Voltage 12 VDC Voltage Regulation -5 +5 % Vout nom Output Power 60 W Output Current 5 ADC

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 PARAMETER DESCRIPTION / CONDITION MIN NOM MAX UNIT Input Fuses (L+N) Not user accessible, quick-acting (F) 25 A OV Threshold V1 13.6 14.2 14.8 VDC OV Latch Off Time V1 1 ms OV Threshold VSB 13.3 13.9 14.5 VDC OV Latch Off Time VSB 1 ms Current limitation Ta < 45°C Ta = 55 °C 248 186 274 212 A Current limit blanking time Time to latch off when in over current 20 22 24 ms Current limit during short time overload V1 Maximum duration 20ms, per module 292 300 308 A Max Short Circuit Current V1 V1 < 3V, per module 3506 A Short circuit latch off time Time to latch off when in short circuit 10 ms Current limitation VSB Per module 6 9 A Current limit blanking time Time to hit hiccup when in over current 1 ms Over temperature on critical points Inlet Ambient Temperature PFC Primary Heatsink Temperature Secondary Sync Mosfet Temperature Secondary OR-ing Mosfet Temperature 115 125 Note: 6 Limit doesn’t include effects of main output capacitive discharge The PWOK_L open collector outputs of all modules are interconnected within the shelf and fed to the signal connector. The same applies to SMB_ALERT_L module and shelf signals. Sink current must not exceed 4 mA on each of these signals. The internal INOK_L signal of individual modules are fed to microcontroller for modules synchronized AC startup. This allows the shelf to start up with load > 3000W during AC application. The microcontroller provide the INOK_L output signal. A pull up resistor of 10kΩ to 3.3V within the shelf provides the high level voltage on PWOK_L, INOK_L and SMB_ALERT_L signals. PWOK_L is low when there is at least one module in operation. INOK_L is low when there is at least one module supplied with correct input voltage. ISHARE signal can be used when shelf are configured for redundant operation. I2C Interface and Signal Connector (RJ45) Pin Out RJ45 PIN OUTS FUNCTION DESCRIPTION 1 7 SCL I2C clock signal line 2 7 SDA I2C data signal line

3 RESET Reset pin of I2C Mux

4 PWOK_L Power OK signal output: active-low

5 INOK_L Input OK signal: active-low

6 SMB_ALERT_L SMB Alert signal output: active-high

7 ISHARE V1 Current share bus

8 SGND Signal ground

Note: 7 External Pull-up resistor should be 2 – 5kΩ to ensure SMBUS compliant signal rise times

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 The PSU Modules are set to a fixed I2C Address (0x20). PMBus communication for the PSU Modules are described in more detail in BCA.00070. The I2C communication to the PSU Modules are routed thru an I2C Multiplexer. The I2C MUX Control Register MUX needs to be configured so that the I2C frames are routed to the correct PSU Module. Refer to the I2C MUX datasheet for additional information. The I2C MUX Address is configurable (via DIP Switch) to allow parallel configuration of several shelves. The I2C MUX has a RESET input which can be used to recover from an I2C bus fault. A logic low signal on this pin resets the I2C MUX. If not used, this pin should be left floating. The shelf default MUX address is 0xEE and Controller address is 0x5E. When DIP switch (SW1) is in “ON” position means 0, “OFF” Position means 1. DIP Switch Position Position Selected Unit 1 A0 2 A1 3 A2 DIP Switch Setting (SW1) A0 A1 A2 MUX ADDRESS (IN HEX) 0 0 0 0xE0 1 0 0 0xE2 0 1 0 0xE4 1 1 0 0xE6 0 0 1 0xE8 1 0 1 0xEA 0 1 1 0xEC 1 1 1 0xEE Note: Communication Manual of shelf, see document BCA.00178.

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 Each PSU front-end module has 2 LEDs to indicate status condition. LED number one is green and indicates AC power is on or off, while LED number two is bi-colored: green and yellow, and indicates DC power presence or fault situations. PARAMETER DESCRIPTION / CONDITION LED SIGNALING AC LED AC Line within range Solid Green AC Line UV condition Off DC LED 8 Normal Operation Solid Green PSON_L High Blinking Yellow (1:1) V1 or VSB out of regulation Solid Yellow Over temperature shutdown Output over voltage shutdown (V1 or VSB) Output under voltage shutdown (V1 or VSB) Output over current shutdown (V1 or VSB) Over temperature warning Blinking Yellow/Green (2:1) Minor fan regulation error (>5%, <15%) Blinking Yellow/Green (1:1) Note: 8 The order of the criteria in the table corresponds to the testing precedence in the controller. WARNING: The USB interface is NOT galvanic isolated and referenced to the +12V_RTN / SGND lines. Preferably, use a battery operated laptop to avoid earth loop issue. If a Desktop Computer is being used, there is a risk of generating earth loop currents, therefore USB Isolators should be used. +12VSB output is capable of delivering 5A. The output is protected by a PTC (16R900GF from Littelfuse). PIN OUTS FUNCTION DESCRIPTION

1 VSB_GND +12VSB return

2 VSB +12VSB output

3 VSB_GND +12VSB return

4 VSB +12VSB output

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 PARAMETER DESCRIPTION / CONDITION CRITERION Agency Approvals (pending) Approved to the latest revisions/amendments of the following standards: (pending) UL 60950-1 Second Edition CAN/CSA-C22.2 No. 60950-1-07 Second Edition IEC 60950-1:2005 EN 60950-1:2006 Approved by independent body (see CE Declaration) (pending) Insulation Input (L/N) to case (PE) Input (L/N) to output Output to case (PE) Basic Reinforced Functional Creepage / Clearance (dC) Primary (L/N) to protective earth (PE) Primary to secondary Electrical Strength Test Input to case Input to output (tested by manufacturer only) Min. 2121Vdc Min. 4242Vdc Max. Leakage Current AC input voltage of TBD VAC, line frequency of 50Hz and a temperature of 25°C. TBD A Conducted Emission EN55022 / CISPR 22: 0.15 … 30 MHz, QP and AVG Class A Radiated Emission EN55022 / CISPR 22: 30 MHz … 1 GHz, QP Class A Harmonic Emissions (per module) IEC61000-3-2, Vin = 115/230 VAC, 50 Hz, 100% Load Class A Acoustical Noise Sound power statistical declaration (ISO 9296, ISO 7779, IS9295) @ 50% load 60 dBA AC Flicker IEC / EN 61000-3-3, dmax < 3.3% PASS ESD Contact Discharge IEC / EN 61000-4-2, ±8 kV, 25+25 discharges per test point (metallic case, LEDs, connector body) A ESD Air Discharge IEC / EN 61000-4-2, ±15 kV, 25+25 discharges per test point (non-metallic user accessible surfaces) A Radiated Electromagnetic Field IEC / EN 61000-4-3, 10 V/m, 1 kHz/80% Amplitude Modulation, 1 µs Pulse Modulation, 10 kHz…2 GHz A Burst IEC / EN 61000-4-4, level 3 AC port ±2 kV, 1 minute DC port ±1 kV, 1 minute A Surge IEC / EN 61000-4-5 Line to earth: level 3, ±2 kV Line to line: level 2, ±1 kV A RF Conducted Immunity IEC/EN 61000-4-6, Level 3, 10 Vrms, CW, 0.1 … 80 MHz A Voltage Dips and Interruptions (per module) IEC/EN 61000-4-11 (per module) 1: Vi 230Volts, 100% Load, Dip 100%, Duration 12ms 2: Vi 230Volts, 100% Load, Dip 100%, Duration < 150 ms 3. Vi 230Volts, 100% Load, Dip 100%, Duration > 150 ms A V1: B, VSB: A B PARAMETER DESCRIPTION / CONDITION MIN NOM MAX UNIT Operating Temperature @ full load, up to 4000 m: @ full load, up to 1800 m: @ 75% load, up to 1800 m: +35 +45 +55 Non-Operating Temperature -40 +70 °C Humidity Operating: @ at 40 °C, non-condensing Non-Operating: non-condensing 5 93 95 %RH Altitude Operating: Non-Operating: 4000 13000 m Shock Operating: 11ms half-sine shocks in Z axis 10+ve, 10-ve Non-Operating: 11ms half-sine shocks in Z axis 10+ve, 10-ve 5 30 g Vibration Operating: 0.2 g rms random Non-Operating: 1g rms random 2 500 200 Hz Acoustic Noise Emissions @ normal operation, and 50% load sharing Fan speed 70 7000 dBA rpm Cooling When equipped with operating PSUs 50 Pa

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 PARAMETER SPSPFE3-0XG Dimensions (W x H x D) 436 x 46.5x 650 mm (overall : 436.5 x 46.75 x 740.75 mm) Weight (Shelf only) 12kg Weight (6 PSU installed) 27kg SHELF DESCRIPTION TYPE MANUFACTURER MPN SPSPFE3-02G Input Connector 3-phase input (2pcs) Positronic Industries SP5YYE48M0LN9A 1/AA-PA1067 USB I2C Connector USB – B type Tyco 292304-1 I2C Interface and Signal Connector RJ45 (2pcs) FCI Connectors 87180-088LF +12VSB output connector Molex 39-30-0040 SPSPFE3-03G Input Connector 3-phase input (2pcs) Positronic Industries SP5YYE48M0LN9A 1/AA-PA1191 USB I2C Connector USB – B type Tyco 292304-1 I2C Interface and Signal Connector RJ45 (2pcs) FCI Connectors 87180-088LF +12VSB output connector Molex 39-30-0040 Note: Ethernet connection is under development Shelf SPSPFE3-02G Input Connector Pin Assignment Front View MPN SP5YYE48M0LN9A1/AA-PA1067 Mating Part SP5YYE1F0091/AA L1 L2 L3 N

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 Shelf SPSPFE3-03G Input Connector Pin Assignment Front View MPN SP5YYE48M0LN9A1/AA-PA1191 Mating Part SP5YYE1F0091/AA SPSPFE3-0XG Front View SPSPFE3-0XG Rear View PSU1 Bay PSU2 Bay PSU3 Bay PSU4 Bay PSU5 Bay PSU6 Bay

© 2015 Bel Power Solutions, Inc. +1.866.513.2839 tech.support@psbel.com BCD.00575_001 SPSPFE3-0XG Isometric View Accessories Blanking Panel Item Number: SPSPFE3BP-01G Mounting “Ear” Brackets for 19” Rack – SPSPFE3-02GA Mounting “Ear” Brackets for 21” Rack – SPSPFE3-02GB

001 Initial Release of Datasheet V001

V002 07-20-2015 Uster R&D NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice.

Product Information

SPSPFE3-02G specifications and overview.

Summary

Modules are hot-swap capable.

Description

Modules are hot-swap capable.

Source title SPSPFE3-02G Datasheet(PDF) - Bel Fuse Inc.

Related Parts

More parts from the same family.

Browse manufacturer