SPL-54-DR-LR2-CDA

SPL-54-DR-LR2-CDA SOURCE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

Features

• Compliant with OC-3/STM-1 and OC-12/STM-4 Standards
• Simplex LC connector
• Single 3.3 V supply
• 80 km reach
• 25 dB Minimum Link Budget
• 1570nm DFB Laser
• Commercial temperature available (-Cxx)
• Industrial temperature available (-Txx)
• SFP MSA SFF-8074i compliant
• Telcordia GR-468 compliant
• Digital Diagnostic SFF-8472 compliant
• Color coded bail latch: Orange
• RoHS compliant (lead free soldered) Parameter Symbol Min. Typical Max. Unit Supply Voltage Vcc 3.135 3.3 3.465 V Total Current Icc - - 300 mA Power Supply Noise Rejectiona PSR 100 - - mVp-p Operating Temperature (-Cxx) Top -5 - 70 ºC Operating Temperature (-Txx) Top -40 - 85 ºC Storage Temperature Tst -40 - 85 ºC Data Rate OC-3/STM-1 DR - 155 - Mbps Data Rate OC-12/STM-4 DR - 622 - Mbps Data Rate Fast Ethernet DR - 125 - Mbps a) 20Hz to 155MHz General operating Parameter Symbol Min Typical Max Unit Optical Power POP -3 -0.5 +2 dBm Average Launch Power Of Off Tx POff - - -45 dBm Extinction Ratio ER 10 - - dB Eye Mask IEEE 802.3 and SONET/SDH Compliant Optical Rise Timeb tr - - 500 ps Optical Fall Timeb tf - 500 ps Mean Wavelength λ 1560 - 1580 nm Spectral Width (20dB) ∆λ - - 1 nm Dispersion Penalty (at 80 Km) - 0.5 1 dB Relative Intensity Noise RIN - - -120 dB/Hz Optical Crosstalk XT - - -45 dB Side Mode Suppression Ratio SMSR 30 - - dB Reflectance Tolerance rp -24 - - dB b) 20%-80% values Transmitter Specifications

SFP Bi-Directional Transceiver Preliminary SPL-54-DR-LR2 Rev 0.1 LUMINENTOIC.COM Parameter Symbol Min Typical Max Unit Input Differential Impedence Rin 80 100 120 Ω PECL Single Ended Data Input Swing Vin,p-p 250 - 1200 mV TxFault_Fault Vfault 2 - Vcc V TxFault_Normal Vnormal Vee - Vee+0.5 V TxDisable_Disable Vd 2 - Vcc V TxDisable_Enable Ven Vee - Vee+0.8 V Transmitter Specifications (Electical) Parameter Symbol Min Typical Max Unit Receive Power Lowc Rsens,low - -30 -28 dBm Receive Power Highc Rsens,high -8 - - dBm Damage Threshold For Receiver Pin,damage - - 0 dBm Wavelength λ 1480 - 1500 nm LOS Assert -38 - - dBm LOS De-assert - - -28 dBm LOS Hysteresis 0.5 - - dB Receiver Reflectance - - - -12 dB c) at 10-12 BER, FE unbalanced pattern, and 10-10 BER, 155.52 Mb/s & 622.08 Mb/s Receiver Specifications Parameter Symbol Min Typical Max Unit PECL Single Ended Data Output Swing Vout, p-p 185 - 800 mV Data Output Rise Time tr - - 500 ps Data Output Fall Time tf - - 500 ps Electrical Output Parameter Symbol Min Typical Max Unit Tx Disable Negate Time t_on - - 1 ms Tx Disable Assert Time t_off - - 10 µs Time To Initialize, Including Reset Of Tx Fault t_init - - 300 ms Tx Fault Assert Time t_fault - - 100 µs Tx Disable To Reset t_reset 10 - - µs Los Assert Time t_loss_on - - 100 µs Los De-assert Time t_loss_off - - 100 µs Serial ID Clock Rate f_serial_clock - - 100 KHz RX_LOS Voltage (High) 2 - - V RX_LOS Voltage (Low) - - 0.8 V LOS Output Voltage-Fault VLOS fault 2 - Vcc V LOS Output Voltage-Normal VLOSnormal Vee - Vee+0.5 V MOD_DEF (0:2)-High Vh 2 - Vcc V MOD_DEF (0:2)-LOW Vl Vee - Vee+0.5 V Timing and Electrical

SFP Bi-Directional Transceiver Preliminary SPL-54-DR-LR2 Rev 0.1 LUMINENTOIC.COM Parameter Range Accuracy Unit Calibration Bit value Formula Temperature (-Cxx) -5 to 70 ±3 ºC Internal 1/256 C Tc(C)=Tad(16 bit signed twos complement)/256 Temperature (-Txx) -40 to 85 ±3 ºC Internal 1/256 C Tc(C)=Tad(16 bit signed twos complement)/256 Voltage 0 to Vcc 0.1 V Internal 100 µV V(Volts)=Vad(16 bit unsigned integer)*0.1 Bias current 0 to 120 5 mA External 0.002mA I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset TX Power -3 to +2 ±2dB dBm External 0.1 µw TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer +TX_PWRoffset RX Power -28 to -8 ±2dB dBm External 0.1 µw RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4 Diagnostics Name of Field Description of Field Address Hex ASCII Vendor Name SFP Vendor name(ASCII) 20 4C L 21 55 U 22 4D M 23 49 I 24 4E N 25 45 E 26 4E N 27 54 T 28 4F O 29 49 I 30 43 C Vendor OUI IEEE vendor OUI code for LuminentOIC Inc. 37 00 38 06 39 B5 Vendor PN Part number in ASCII, e.g. SPL-54-DR-LR2-CDA 40 53 S 41 50 P 42 4C L 43 35 5 44 34 4 45 44 D 46 52 R 47 4C L 48 52 R 49 32 2 50 43 C 51 44 D 52 41 A EEPROM Serial ID

SFP Bi-Directional Transceiver Preliminary SPL-54-DR-LR2 Rev 0.1 LUMINENTOIC.COM Pin Function Notes

1 VeeT TX Ground

2 TX_FAULT Open Collector

3 TX_DISABLE Internally Pulled High

4 MOD_DEF2 Serial Data Input

5 MOD_DEF1 Serial Clock Input

6 MOD_DEF0 Internally Grounded

7 NC Not Connected

8 LOS Open Collector

9 VeeR RX Ground

10 VeeR RX Ground

11 VeeR RX Ground

12 RXD- RX Data Negative

13 RXD+ RX Data Positive

14 VeeR RX Ground

15 VccR RX Power

16 VccT TX Power

17 VeeT TX Ground

18 TXD+ TX Data Positive

19 TXD- TX Data Negative

20 VeeT TX Ground

SFP Bi-Directional Transceiver Preliminary SPL-54-DR-LR2 Rev 0.1 LUMINENTOIC.COM Outline drawing Units in mm (inches)

SFP Bi-Directional Transceiver Preliminary SPL-54-DR-LR2 Rev 0.1 LUMINENTOIC.COM Protocol IC SerDes Laser Driver Receiver Amplifier LuminentOIC SFP Vcc 10F 0.1F .01F VCCT 10K TX_DISABLE TX_FAULT TD + TD - VEET .01F .01F 100 VCCR 10F 0.1F .01F .01F 100 EEPROM MOD_DEF 2 MOD_DEF 1 MOD_DEF 0 RD + RD - RX_LOS TX_DISABLE TX_FAULT RX_LOS R1R1R1 R VEER Vcc R1=4.7K to 10K Suggested Transceiver Interface

LUMINENTOIC.COM SFP Bi-Directional Transceiver Preliminary SPL-54-DR-LR2 IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran ties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu- ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Warnings: Legal Notes: LUMNDS1691-Apr3007 Rev 0.1

Ordering Information

Available Options:ɹ SPL-54-DR-LR2-CDA SPL-54-DR-LR2-CNA SPL-54-DR-LR2-TDA SPL-54-DR-LR2-TNA Part numbering Definition: SPL - 54 - DR - LR2 - Temperature Diagnostic Revision

• SPL = LC connector
• 54 = Tx 1570nm/Rx 1490nm
• DR = Dual Rate 155M/622M
• LR2 = Reach 80 km
• Operating Temperature C = Commercial temperature (-5 to 70ºC) T = Industrial temperature (-40 to 85ºC)
• D = Digital Diagnostic (SFF-8472) N = No Diagnostic
• Design Revision A = RoHS compliant (lead free soldered)