SPGM401M

SPGM SPSEMI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

反应速度快50ns ADSL MODEM、FAX、TEL 体积小,贴片封装更有竟争力 RS485、RS232、CAN一级防护 能流能力大 Security and fire alarm systems 静态电容量小，绝缘性好 1 2 3 4 型号 Part Number 直流起始放电电 压 DC Spark- Over Voltage Vs(V) 绝缘阻抗 Insulation Resistance IR(OHM)/DC 电容量 Capacitance 1KHZ-6Vmax C(pf) 耐冲击电流 Surge Current Capacity 8/20us 寿命测试Sureg Life Test SPGM141N 140 ＞100M/50V 产品尺寸/Dimensions(mm) 产品参数/Electrical characteristics SPGM201M 200 SPGM301M 300 SPGM401M 400 SPGM501M 500 SPGM601M 600 SPGM701M 700 SPGM102M 1000 SPGM152M 1500 色环代码/Color Code ＜0.8 10KV ＞1000A 10KV 100A ＞ 200次 ＞100M/100V ＞100M/250V ＞100M/500V SPG/SPGM Series 型号Part Number Color Code 2 SPGM141N SPGM201M SPGM301M SPGM401M SPGM501M SPGM601M SPGM701M Blue P u r p l e Color Code 1 Color Code 3 Yellow Green Brown Red Orange SPGM102M SPGM152M GreenBLack Purple Black Red

项目 Test Item 直流放电电压 DC-Spark-Over Voltage Vs 内绝缘电阻 Insulation Resistance 静态电容 Capacitance C(pF) 实验项目 Test Item 放置于-40℃±3℃的环境中1000小时后，取出置于 在规定的设定直流电压下，跨在两端引线。即可测 量其内绝缘电阻值。(Measure the insulation resistance of two end of leadwire under the specified DC voltage.) 大于等于100MΩ(100MΩ min.) 使用频率1KHz与并两端加载小于或等于6V直流电压 的电源。即可量出其静态电容量Measure the Electrostatic Capacitance under the test condition of 1KHz,DC 6V(max). 小于或等于1pF (1pF max.) 环境试验测试/Enviromental Characteristics 试验方法 Test Method 结果Specification 基本参数特性测试/Initial Characteristics 测试条件 Test Method 结果Specification 使用一直流电源，并逐渐地增加测量电压，测试电 流为1ma，测试时间最大为一秒 （1sec）.(1mA)(Add and measure the DC Voltage gradually Maxto get the discharge threshold voltage. The measuring current is 1mA/1 second max.) 依规格书值而定 (It depands on each spec.) 耐寒性 耐热性 耐温性 温度周期 为1周期，重复25次后，取出置于常温/常温中4小 时后，检测直流放电电压，绝缘阻抗，静态电容量 及检查外观25 times repetition of cycle -40± 3℃ (30 Min.),roon temp., (4 Min.), 125± 2℃(30 Min.),room temp., normal humidity(4hrs) . 满足各个特性相关参数值 Within standard mentioned in Initial Characteristics. 放置于-40℃±3℃的环境中1000小时后，取出置于 常温中4小时后，检测直流开始放电电压，绝缘阻 抗，静态电容量及检查外。After -40± 3℃ (1000hrs) / room temp.,normal humidity(4 hrs) cycle, measure the properties. 满足各个特性相关参数值 Within standard mentioned in Initial Characteristics. 放置于125℃±2℃的环境中1000小时后，取出置于 常温中4小时后，检测直流开始放电电压，绝缘阻 抗，静态电容量及检查外。After 125± 2℃ (1000hrs) / room temp.,normal humidity(4 hrs) cycle, measure the properties. 满足各个特性相关参数值 Within standard mentioned in Initial Characteristics. 放置于85℃±2℃ RH85%的环境中1000小时后，取 出置于常温中4小时后，检测直流开始放电电压， 绝缘阻抗，静态电容量及检查外。After 85℃± 2℃ RH85%(1000hrs) / room temp.,normal humidity(4 hrs) cycle, measure the properties. 满足各个特性相关参数值 Within standard mentioned in Initial Characteristics. SPG/SPGM Series

实验项目 Test Item 浪涌承受能力 突波寿命测试 实验项目 Test Item 拉力强度 施加2.5KG负重于引线约30秒钟后，检测直流放电 电压，绝缘阻抗，静态电容及检查外观 (Apply 2.5 kgs load approximately 30 seconds, then check for pull-out and breaking of the lead wire.) 满足各个特性相关参数值 Within standard mentioned in Initial Characteristics. 让一只玻璃放电管与一只1500pF的电容并于电源两 端，每间隔10秒施加10KV电压,做200次.(Apply 10 KV voltage charged in 1500pF condenser and apply the current to the specimen,200 times at 10 seconds of intervals.) 满足各个特性相关参数值 Within standard mentioned in Initial Characteristics. 环境试验测试/Enviromental Characteristics 试验方法 Test Method 结果Specification 浪涌寿命测试/Surge Characteristics 试验方法 Test Method 结果Specification 在玻璃放电管置于8/20us的浪涌测试仪两端，施加 该型号相对应的耐冲击电流，间隔时间为60s 正负 各测试5次。检测其直流电压，绝缘阻抗，静态电 容及检查外观 直流放电电流Vs/Vs≦30% (DC spark-over volatage JSE: △Vs/Vs≦30%) 弯曲强度 实验项目 Test Item 焊锡附着性 焊锡耐热性 将沾过助焊剂之导线，自距离导线迷熔接点根部 3mm处起，浸于265±5℃之焊锡液中5秒钟后，将导 线之助焊剂洗净后，检查焊锡附着情况.(Apply flux and immerse in molten solder, up to the point of 3mm from the body,for 5 sec. (235℃±5℃). Wash the leadwire and check for soldering adhesion.) 导线需均匀附着90%以上(Lead wire is evenly covered by solder over 90%.) 将沾过助焊剂之导线，自距离导线迷熔接点根部 3mm处起，浸于265±5℃之焊锡液中10秒钟后，检 测直流放电电压，绝缘阻抗抗，静态电容及检查外 观.(Apply flux and immerse in molten solder, up 满足各个特性相关参数值 Within standard mentioned in 距离引线熔接点根部绝3mm处，使用曲率半径为 0.75-0.8mm器具，与轴方向垂直角度，负重 0.25Kg，弯曲后回复原状，反复2次后，检测直流 放电电压，绝缘阻抗，静态电容及外观(Bend the lead wire, with jig which radius is 0.75~0.8mm, at the point of 2mm from the body, under 0.25 kgs load applied at the right angle the direction of the amis and get the bent lead wire back to its original poing after the procedure was repeated 2 times.) 满足各个特性相关参数值 Within standard mentioned in Initial Characteristics. 环境试验测试/Enviromental Characteristics 试验方法 Test Method 结果Specification 焊锡耐热性 观.(Apply flux and immerse in molten solder, up to the point of 3mm from the body,for 5 sec. (235 ℃±5℃). Wash the leadwire and check for soldering adhesion.) Within standard mentioned in Initial Characteristics. SPG/SPGM Series