SP4062 LITTELFUSE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Features

  • ESD, IEC61000-4-2, ±30kV contact, ±30kV air
  • EFT , IEC61000-4-4, 40A p=5/50ns)
  • Lightning, IEC61000-4-5, 20A (t p=8/20µs)
  • Low capacitance of 3.5pF (TYP) per I/O
  • Low leakage current of 1µA (MAX) at 3.3V
  • 10/100/1000 Ethernet Interfaces
  • Customer Premise Equipment (CPE)
  • VoIP Phones
  • Set Top Boxes
  • PBX Systems Functional Block Diagram GND13 Pinout 13 5 GND Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. RoHS Pb GREEN Application Example RJ-45 Connector *Package is shown as transparent Ethernet PHY Tx+ Tx- Rx- Rx+ SP4062 PHY SP4062 Series 3.3V 20A Rail Clamp Array

185©2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. TVS Diode Arrays (SPA™ Family of Products) Revision: June 27, 2011 SP4062 Series SP4062 Lightning Surge Protection - SP4062 Series CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Absolute Maximum Ratings Symbol Parameter Value Units IPP Peak Current (tp=8/20μs) 20.0 A PPK Peak Pulse Power (tp=8/20µs) 300 W TOP Operating Temperature -40 to 85 ºC TSTOR Storage Temperature -50 to 150 °C Electrical Characteristics (TOP=25ºC) Parameter Symbol Test Conditions Min Typ Max Units Reverse Standoff Voltage VRWM 3.3 V Snap Back Voltage VSB ISB=50mA 2.8 V Reverse Leakage Current ILEAK VR=2.5V , I/O to GND 0.5 1. 0 µA Clamp Voltage1 VC IPP=1A, tp=8/20µs, Fwd 6.0 V IPP=5A, tp=8/20µs, Fwd 7. 0 V IPP=10A, tp=8/20µs, Fwd 8.0 V IPP=20A, tp=8/20µs, Fwd 11. 5 V Dynamic Resistance RDYN (VC2-VC1)/(IPP2-IPP1) 0.25 Ω ESD Withstand Voltage1 VESD IEC61000-4-2 (Contact) ±30 kV IEC61000-4-2 (Air) ±30 kV Diode Capacitance1 CI/O-GND Reverse Bias=0V 3.5 5.0 pF Diode Capacitance1 CI/O-I/O Reverse Bias=0V 2.0 pF Note: 1. Parameter is guaranteed by design and/or device characterization. Thermal Information Parameter Rating Units Storage Temperature Range -65 to 150 °C Maximum Junction Temperature 150 °C Maximum Lead Temperature (Soldering 20-40s) 260 °C Clamping Voltage vs. IPPPulse Waveform 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 110% Time (/uni03BCs) Percent of IPP 0 5 10 15 20 Peak Pulse Current-IPP (A) 0.0 2.0 4.0 6.0 10.0 12.0 Clamp Voltage (VC) 8.0

©2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. 186 TVS Diode Arrays (SPA™ Family of Products) Revision: June 27, 2011 SP4062 Series Lightning Surge Protection - SP4062 Series Capacitance vs. Bias Bias Voltage (V) Capacitance (pF) 0.0 1.0 2.0 3.0 4.0 5.0 Time Temperature TP TL TS(max) TS(min) tP tL tS time to peak temperature PreheatPreheat Ramp-upRamp-up Ramp-downRamp-do Critical Zone TL to TP Critical Zone TL to TP Reflow Condition Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (t p) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Soldering Parameters

Ordering Information

Part Number Package Marking Min. Order Qty. SP4062-04UTG uDFN-10 UH4 3000 Part Numbering System Part Marking System SP 4062 04 U T G Series Number of Channels Package U= uDFN-10 T= Tape & Reel G= Green Silicon Protection Array (SPA TM Family of TVS Diode Arrays U H 4 Product Series U = SP4062 Assembly Site Number of Channels Product Characteristics Lead Plating Pre-Plated Frame Lead Material Copper Alloy Lead Coplanarity 0.0004 inches (0.102mm) Subsitute Material Silicon Body Material Molded Epoxy Flammability UL94-V-0 Notes : 1 . All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. All specifications comply to JEDEC SPEC MO-223 Issue A 5. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 6. Package surface matte finish VDI 11-13.

187©2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com/SPA for current information. TVS Diode Arrays (SPA™ Family of Products) Revision: June 27, 2011 SP4062 Series SP4062 Lightning Surge Protection - SP4062 Series Package Dimensions — uDFN-10 uDFN-10 (2.6x2.6mm) Symbol Millimeters Inches Min Nom Max Min Nom Max A3 0.130 Ref 0.005 Ref e 0.50 BSC 0.020 BSC D E B Top View A A Bottom View 0.10 C b C Seating Plane Side View

0.10 C BM A

0.05 C e C Embossed Carrier T ape & Reel Specification — uDFN-10 (2.6x2.6mm) T B0K0 P2 D0 E F W 5º MAX A0 5º MAX Symbol Millimeters A0 2.82 +/- 0.05 B0 2.82 +/- 0.05 D0 Ø1 .50 + 0.10 D1 Ø 0.50 + 0.05 E 1 .75 +/- 0.10 F 3.50 +/- 0.05 K0 0.76 +/- 0.05 P0 4.00 +/- 0.10 P1 4.00 +/- 0.10 P2 2.00 +/- 0.05 T 0.25 +/- 0.02 Recommended Solder Pads uDFN-10L 2.6x2.6mm B CF XP GZ Y Dimension Symbol Millimeters Inches B 2.30 0.091 C 2.20 0.087 F 1 .41 0.056 G 1 .65 0.065 P 0.50 0.020 X 0.37 0.015 Y 0.55 0.022 Z 2.75 0.108

Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: SP4062-04UTG