SP02C-XX-XXX

MIL-DTL-26482_V01 AIO | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 52

Technical content

97 Series Connectors are UL recognized and CSA recognized. AMPHENOL CORPORATION Amphenol Industrial Phone: 888-364-9011

191 Delaware Avenue

Sidney, NY 13838-1395 www.amphenol-industrial.com Notice: Speci/f_i cations are subject to change without notice. Contact your nearest Amphenol Corporation Sales Of/f_i ce for the latest speci/f_i cations. All statements, information and data given herein are believed to be accurate and reliable but are presented without guarantee, warranty, or responsibility of any kind expressed or implied. Statements or suggestions concerning possible use of our products are made without representation or warranty that any such use is free of patent infringement and are not recommendations to infringe any patent. The user should not assume that all safety measures are indicated or that other measures may not be required. Speci/f_i cations are typical and may not apply to all connectors. Amphenol 97 Series Connectors are UL recognized and CSA recognized. www.amphenol-industrial.com PT Series Miniature Cylindrical Connectors 12-070-20 Amphenol AMPHENOL CORPORATION Amphenol Industrial Phone: 888-364-9011 Sidney, NY 13838-1395 www.amphenol-industrial.com

Proprietary/MIL-DTL-26482 Series 1 connectors covered in this catalog are widely used in general duty and environmental applications, both industrial and military. Markets that use this family of connectors include:

• Instrumentation
• Monitoring Equipment
• Machine Tool, Factory Automation
• Communications
• Geophysical
• Industrial Controls and Robotics
• Oil and Petrochemical Industries
• Rail/Mass Transit
• Military/Aerospace Table of Contents Page Introduction, Amphenol® Miniature Cylindrical PT, SP, MS/PT Proprietary/MIL-DTL-26482, Series 1 Bayonet Coupling, Solder Contacts PT Connectors with Printed Circuit Board Contacts - PT-SE, SP-SE, MS/PT-SE Proprietary/MIL-DTL-26482, Series 1 Bayonet Coupling, Crimp Contacts If more information is needed concerning the connectors covered in this publication, or if there are special application needs, please contact: Amphenol Corporation Amphenol Industrial Operations

Sidney, New York 13838-1395 Telephone: 888-364-9011 Fax: 520-397-7169 Please go to the Amphenol websites to view, download and save this catalog and most all of Amphenol interconnection product literature. www.amphenol-industrial.com Some miniature connector styles are available in RoHS Compliant versions. Please contact Amphenol Industrial Operations for more information. Amphenol operates Quality Systems that are certified to ISO 9001:2015; ISO 14001:2015; ISO/TS 16949:2016 by third party registrars. NOTE: The connector products in this brochure were formerly known as Bendix® products. These products are now manufactured and sold under the Amphenol® brand name. The name “Amphenol” will replace the name “Bendix” on products and literature in the future. NOTE: The Miniature MIL-DTL-26482, Series 2 connectors PTS-DR and MS/PTS-DR (formerly in this catalog) are no longer supplied with these designations. Amphenol now supplies the Amphenol®/ Matrix® MIL-DTL-26482, Series 2. (Military numbers include MS3470 - MS3472, MS3474, - MS3476).

Amphenol® Miniature Cylindrical Connectors Proprietary/MIL-DTL-26482, Series 1 Amphenol® Miniature Cylindrical connectors offer twice the number of contacts in just half the size of a Standard connector. These miniature connectors, are available in several series, each with varying design characteristics and customer options to meet cost considerations and provide maximum design flexibility. There are two styles within the family that are MS approved and qualified to MIL-DTL-26482, Series 1, and in addition there are several proprietary styles. Common features of all styles:

• All are for general duty applications and environmental sealing is achieved with the grommet and clamp design.
• Operating temperature is from –55°C to +125°; Operating voltage to 1000 VAC (RMS) at sea level.
• Pin and socket contacts are machined from low loss copper alloy and gold plated to eliminate contact corrosion and provide an indefinite shelf life.
• All have resilient inserts which provide high dielectric strength and moisture barrier.
• A variety of shell finishes (including non-cadmium) and a variety of back-end accessories are available within the styles. Bayonet Coupling with Solder Contact Termination Bayonet Coupling with Crimp Contact Termination PT Solder jam nut receptacle and mated straight plug PT Solder wall mount receptacle PT-SE Crimp wall mount receptacle and mated straight plug PT, MS/PT (solder)
• MS and proprietary versions
• Factory installed solder contacts
• 3 point bayonet coupling and 5 key/key- way mating.
• Intermateable with all miniature series connectors.
• MS/PT meets MIL-DTL-26482 Series 1, service classes E, F and P.
• MS/PT is UL recognized. SP (solder)
• SP Series is a modification of the PT with same features except a wider flange for back panel mounting Options
• 7 shell styles with 60 insert patterns
• Hermetic seal (glass fusion) receptacle styles available
• Pressurized thru bulkhead receptacle style available
• Per-installed coax solder con- tacts are available
• Printed circuit board contacts are available PT-SE, MS/PT-SE (crimp)
• MS and proprietary versions
• Crimp rear insertable/front release contact termination. (closed entry socket insert prevents probe damage).
• 3 point bayonet coupling and 5 key/key- way mating.
• Intermateable with all miniature series connectors.
• MS/PT-SE meets MIL-DTL-26482 Series 1, service classes E, F, P. SP-SE (crimp)
• Modification of the PT-SE with wider flange for back panel mounting Options
• 6 shell styles with 47 insert patterns
• Coax and thermocouple con- tacts are available

The large family of miniature proprietary and MS style connectors provides for many optional features and designs. In addition to the choices of bayonet or threaded shells, solder or crimp termination within the style variations, there are additional options that are shown here. Hermetics Hermetically sealed receptacles have fused compression glass sealed inserts which provide environmental moisture sealing. There are three hermetic styles within the PT bayonet series. Coaxial Contacts Amphenol Miniature connectors can incorporate shielded coax contacts. Size 8 and 12 crimp coax contacts are available in PT-SE, SP-SE, MS/PT-SE. Factory installed size 8 and 12 solder type coax contacts are available in PT, SP, MS/PT connectors. See coax contact information pages at the end of this catalog. Printed Circuit Board Tail Contacts PT bayonet connectors in box mounting receptacle and jam nut receptacle styles are available with printed circuit board contacts. Standard PCB tails for MIL-DTL-26482 connectors have gold plating, .0050 inches over nickel. See page 20 and call Amphenol for further information. Flex Circuitry Flex termination assemblies for attaching cylindrical connectors to printed circuit boards are available through the Amphenol division ACT, Advanced Circuit Technology. Flex can be used with miniature 26482 connectors and it can be designed to meet specific length, current carrying capacity and to fit the precise geometric shape of the connector to board package. Flex circuity plugs into a printed circuit board and creates a self-locking terminal pad which eliminates the need for an additional interconnect to the PCB. Filter Protection Amphenol offers the FPT Series which combines the miniature PT series with an EMI filter. Designed to provide EMI protection for sensitive circuits, each circuit is individually filtered within the connector, eliminating the need for costly and bulky exterior network filters. Filter contacts are available in MF, HF, VHF, and UHF ranges and are intermateable and intermountable with MIL-DTL-26482 connectors. For further information see catalog 12-120, Amphenol EMI Filter Transient Protection Connectors. Overmolded Cable Overmold seals and cables can be designed for almost any industrial application. A variety of materials are available: neoprene, hypalon and others; and a variety of lengths can be designed to meet customer specifications. Overmold seals to the rear of the connector and to the cable jacket providing moisture sealing. Amphenol Miniature Cylindrical design flexibility PT Connector with Hermetic Seal Insert and Coax Contacts PT Connector with PC Tail Contacts PT Connector with Flex PT Connector with EMI Filter Protection PT Connector with Overmolded Cable

Amphenol Miniature Cylindrical connector selection guide CHARACTERISTICS Solder Crimp PT MS/PT SP MS/ PT-SE PT-SE Intermateable† O O O O O Contacts Solder • • • Crimp Ri/FR • • Contact Retention System Non-Removable • • • Removable • • Coupling Bayonet • • • • • Standard Finishes†† Olive Drab Cadmium (003) • • • • Anodic Coated (005) • Temperature Range Resilient Dielectric (-55°C to +125°C) • • • • • Wide Mounting Flange • Hermetic Seal • • • SHELL STYLE AVAILABILITY thru-bulkhead Receptacle “TB” • • Solder Mount Receptacle “I” *• * • The accompanying chart is provided to assist the user in selecting the appropriate type of miniature connector to meet the application requirements. Further information can be found in specific sections of this catalog. RI/FR = Rear Insertion/Front Releasable † o intermates with o †† Optional finishes available. See “how to order” sections. * Available in hermetic version Dual mounting holes * This connector style is sometimes referred to as a cable connecting “plug.” It does, however, mate with either a straight or 90 degree plug.

Amphenol Miniature Cylindrical insert availability Insert Arrangement Solder Termination Crimp Termination Screw Termination Total Contacts Contact Size MS/PT PT SP Hermetic PT MS-PT MS/PT-SE PT-SE SP-SE PT 20 16 12 10 8 Coax Service Rating12 8 6-1 X X X* 1 1 I 8-2 X X X X 2 2 I 8-3 X X X X 3 3 I 8-4 X X X X 4 4 I 8-33 X X X X X 3 3 I 8-98 X X 3 3 I 10-2 X X 2 2 I 10-5 X X X* 5 5 I 10-6 X X X X X 6 6 I 10-7 X X X 7 7 I 10-70 X X 1 1 Coax 10-98 X X X X* 6 6 I 12-3* X X X X X 3 3 II 12-4 X X X* 4 4 I 12-8 X X X X* X 8 8 I 12-10 X X X X X 10 10 I 12-14 X X 14 14 I 12-98 X X 10 10 I 14-2 X X 2 2 II 14-4 S S X 4 4 I 14-5 X X X X X 5 5 II 14-8 X X 8 6 2 I 14-12 X X X X X 12 8 4 I 14-15 X X X X X 15 14 1 I 14-18 X X X X* X 18 18 I 14-19 X X X X X 19 19 I 14-22 X* 5 1 4 I 14-71 P X 4 3 I 14-91 HV S X X* 3 3 1 ** 14-AA X X X 4 4 I 16-8 X X X X X 8 8 II 16-23 X X X X 23 22 1 I 16-26 X X X X X 26 26 I 16-70 X X 15 14 1 N/A 16-99 X X X X 23 21 2 I 18-2 X X X 2 2 II 18-3 X X X X 3 3 II 18-5 X X X* 5 5 II 18-8 X 8 8 I 18-11 X X X X X 11 11 II 18-30 X X X X* X 30 29 1 I *Not available in MS version Flashover voltage 5,000 VAC (RMS) *1500 VAC (RMS) S designates Socket insert only. P designates Pin insert only. †Size 12 contacts for #10 wire ††Not presently tooled †††Contacts must be ordered separately

Amphenol Miniature Cylindrical insert availability, cont. Insert Arrangement Solder Termination Crimp Termination Total Contacts Contact Size MS/PT PT SP Hermetic PT MS-PT MS/PT-SE PT-SE SP-SE 20 16 12 Coax Service Rating12 8 18-32 X X X X X 32 32 I 18-71 X* 9 8 1 Coax, II 18-72 X X 14 10 4 N/A 18-75 X X 4 4 Coax 18-76 4 3 1 II 18-80 X X 8 6 2 Coax, I 18-91 HV X* 6 6 ** 20-16 X X X X X 16 16 II 20-24 X X X 24 24 I 20-25 X X 25 25 I 20-26 X X 26 20 6 I 20-27 X X X 27 27 I 20-39 X X X X X 39 39 2 I 20-41 X X X X X 41 41 I 20-70 14 10 4 Coax 20-90 HV X X 7 7 Hi-Voltage 22-7 X X X* 7 7 Coax 22-21 X X X X X 21 21 II 22-25 X* 25 25 I 22-32 X X X X 32 32 I 22-34 X X 34 34 I 22-36 X X 36 36 I 22-41 X X X X X 41 27 14 I 22-55 X X X X X 55 55 I 22-70 X X 19 13 6 I, Coax 22-71 9 2 7 I, Coax 22-72 X X 19 12 4 3 N/A 22-78††† X* 7 7 Coax 22-96 X* 7 7† II 24-31 X X 31 31 I 24-51††† X* 51 47 4 I 24-61 X X X X X 61 61 I 24-71 X X 49 45 2 2 N/A 24-79 1 1 5 Coax *Not available in MS version Flashover voltage 5,000 VAC (RMS) *1500 VAC (RMS) †Size 12 contacts for #10 wire ††Not presently tooled †††Contacts must be ordered separately

Amphenol Miniature Cylindrical alternate positioning A B A B A B A B Alternate Positioning To avoid cross-plugging problems in applications requiring the use of more than one miniature cylindrical connector of the same size and arrangement, alternate insert rotations are available as indicated in the accompanying chart. As shown in the diagram at right, the front face of the pin insert is rotated within the shell in a clockwise direction from the normal shell key. The socket insert would be rotated counterclockwise the same number of degrees in respect to the normal shell key. Insert Rotation Shell Size Insert Arrangement Degrees W X Y Z 6 6-1 - - - - 8 8-2* 58 122 - - 8 8-3 60 210 - - 8 8-4* 45 97 184 - 8 8-33* 90 - - - 8 8-98 - - - - 10 10-2 45 90 315 - 10 10-5* 45 151 180 270 10 10-6* 90 - - - 10 10-7 90 - - - 10 10-70 - - - - 10 10-98* 90 180 240 270 12 12-3 - - 180 - 12 12-4* 38 - - - 12 12-8 90 112 203 292 12 12-10* 60 155 270 295 12 12-14 - - - - 12 12-98* 61 135 189 340 14 14-2 58 122 - - 14 14-4* 45 - - - 14 14-5* 40 92 184 273 14 14-8 48 162 189 312 14 14-12* 43 90 - - 14 14-15* 17 110 155 234 14 14-18* 15 90 180 270 14 14-19* 30 165 315 - 14 14-22 45 - - - 14 14-71 - - - - 14 14-91HV - 60 - - 14 14-AA* 45 - - - 16 16-8* 54 152 180 331 16 16-23 158 270 - - 16 16-26* 60 - 275 338 16 16-70 41 122 216 286 16 16-76 - - - - 16 16-99* 66 156 223 340 18 18-2 58 122 - - 18 18-3 - - 180 - Insert Rotation Shell Size Insert Arrangement Degrees W X Y Z 18 18-5 55 97 263 315 18 18-8 180 - - - 18 18-11* 62 119 241 340 18 18-30* 180 193 285 350 18 18-32* 85 138 222 265 18 18-71 18 108 127 215 18 18-72 53 102 213 293 18 18-75 45 - - - 18 18-76 - - - - 18 18-80 45 90 135 160 18 18-91HV 90 180 240 270 20 20-16* 238 318 333 347 20 20-24 70 145 215 290 20 20-25 72 144 216 288 20 20-26 13 107 210 322 20 20-27 72 144 216 288 20 20-39* 63 144 252 333 20 20-41* 45 126 225 - 20 20-70 63 135 222 335 20 20-90 45 135 225 315 22 22-7 19 41 - - 22 22-21* 16 135 175 349 22 22-25 60 125 211 336 22 22-32 72 145 215 288 22 22-34 62 142 218 298 22 22-36 72 144 216 288 22 22-41 39 135 264 - 22 22-55* 30 142 226 314 22 22-70 30 82 218 312 22 22-71 33 191 236 270 22 22-72 42 200 277 339 22 22-78 19 41 - - 22 22-96* 19 41 - - 24 24-31 90 225 255 - 24 24-51 22 171 313 - 24 24-61* 90 180 270 324 24 24-71 39 131 205 281 24 24-79 - - - - * Available in Hermetic Class Position W Position X Position Y Position Z Views looking into front face of pin insert or rear of socket insert.

Amphenol Miniature Cylindrical insert arrangements AB A B C A B C D AC B A C B BA Insert Arrangement 6-1 8-2 8-3 8-4 8-33 8-98 10-2 Service Rating I I I I I I I Number of Contacts 1 2 3 4 3 3 2 Contact Size 20 20 20 20 20 20 16 A D C B E AF E D C B A FE DC B AC B A D C B Insert Arrangement 10-5 10-6 10-7 10-70 10-98 12-3 12-4 Service Rating I I I COAX I II I Number of Contacts 5 6 7 1 6 3 4 Contact Size 20 20 20 8 COAX 20 16 16 A H G F E D C B A KJ H G F E D C B A PN M L KJ HF ED CB R A B C D E F G H JK AD BC A E DC B Insert Arrangement 12-8 12-10 12-14 12-98 14-2 14-4 14-5 Service Rating I I I I II I II Number of Contacts 8 10 14 10 2 4 5 Contact Size 20 20 20 20 12 12 16 A BH C D E F G A D C B H G F E M L K J A H G F E D C B M L K J R P N A D C B H GF E M L K JP N UT SR A D C B H G F E M L K J T S R PN U V A D C B E D A C B Insert Arrangement 14-8 14-12 14-15 14-18 14-19 14-22 14-71 Service Rating I I I I I I I Number of Contacts 6 2 8 4 14 1 18 19 1 4 3 1 Contact Size 20 12 20 16 20 16 20 20 20 12 16 8 COAX

Amphenol Miniature Cylindrical insert arrangements A C B A D C B A D C B H G F E A H G F E D C B PN M L K J Z Y X W V U T S R A Z Y X W V U TS R P N M L K J H G F E D C B a b c Insert Arrangement 14-91HV 14-AA 16-8 16-23 16-26 Service Rating Flashover 5,000 VAC (RMS) I II I I Number of Contacts 3 4 8 22 1 26 Contact Size 20 12 16 20 16 20 A H B J K DL R E M F N G P C A M L K J H G F E D C B P N A M L K J H G F E D C B TS R P N ZY X W V U Insert Arrangement 16-70 16-76 16-99 18-2 18-3 Service Rating N/A Flashover 1,500 VAC (RMS) I II II Number of Contacts 14 1 8 1 5 21 2 2 3 Contact Size 20 12 COAX 20 12* 2 COAX 20 16 8 10 *Contact Positions Optional A E DC B A H G F ED C B A L K J H G F E D C B A Z Y X W V U T S R P N M L K J H G F E D C B a b c d e fg Insert Arrangement 18-5 18-8 18-11 18-30 Service Rating II I II I Number of Contacts 5 8 11 29 1 Contact Size 12 12 16 20 16 A Z Y X W V U TS R P N M L K J H G F E D C B a b c d e f g h j A H G F E D C B J A B C MP L N D E H F G J K AD CB Insert Arrangement 18-32 18-71 18-72 18-75 Service Rating I II, COAX N/A COAX Number of Contacts 32 8 1 10 4 4 Contact Size 20 16 8 COAX 20 12 COAX 8 COAX

Amphenol Miniature Cylindrical insert arrangements A D C B A G F E D C BH A F E DC B A M L K J H G F E D C B S R P N Insert Arrangement 18-76 18-80 18-91 HV 20-16 Service Rating II I, COAX Flashover 5,000 VAC (RMS) II Number of Contacts 3 1 6 2 6 16 Contact Size 12 COAX 8 COAX 20 8 COAX 20 16 A Z Y XW V U T S R P N ML K J H G F E D C B a A Z Y X W V U T S R PN M L K J H G F E DC B a b A B C D E F GH JK LM N P R S T U V W X Y Z a bc A Z Y X W V U T S R P N M L K J H G F E D C B a b cd Insert Arrangement 20-24 20-25 20-26 20-27 Service Rating I I I I Number of Contacts 24 25 20 6 27 Contact Size 20 20 20 12 20 A Z Y X WV U T S R P N M L K J H G F E D C B ar p n m k j h g f e d c b i q A Z Y XW V U T S R P N M L K J H G F E D C B at s r pq n m k j i h g f e d c b A P N M L K J G F E D C B H A G F ED C B Insert Arrangement 20-39 20-41 20-70 20-90 Service Rating I I COAX HI-VOLTAGE Number of Contacts 37 2 41 10 4 7 Contact Size 20 16 20 20 8 COAX 20 A G D C BF E A X W V U T S R P N M L K J H G F E D C B A Z Y X W V U T S R P N M L K J H G F E D C B ab A RP N M Bb Sa h c Z T L C jg d Y X K J H W V G F U E D f e Insert Arrangement 22-7 22-21 22-25 22-32 Service Rating COAX II I I Number of Contacts 7 21 25 32 Contact Size 8 COAX 16 16 20

Amphenol Miniature Cylindrical insert arrangements A Z Y X W V U T S R P N M L K J H G F E D C B a lk j h g f e d c b ATS B V UR C f WP D m h ge X N E n l jd M L K J a c b Z Y H G F k A ZY X W V U T S R P N M L K J H G F E D C B a t s r q p n m k j i h g f e d c b A Z YX W V UT S R P N M L K J H G F E D C B a x w v u t s r q pn m y k j i h g f e d c b z HH GG FF EE DD CC BB AA Insert Arrangement 22-34 22-36 22-41 22-55 Service Rating I I I I Number of Contacts 34 36 27 14 55 Contact Size 20 20 20 16 20 V KD T P B LC E H M J F G RS N A U A G F E D C B HJ A V F E N L T J HD MR G P S U C KB A G F E D C B Insert Arrangement 22-70 22-71 22-72 22-78 Service Rating i, COAX I, COAX N/A COAX Number of Contacts 12 6 2 7 12 4 3 7 Contact Size 20 8 COAX 20 8 COAX 20 16 8 COAX 8 COAX A G F E D C B A X W V U T S R Q P Y N M L K J H GF E D C B Z a g f e d c b B C D E F G H K i j NP R S T U V W X Y Z a A b d e f J M h m n p q r y t L g BBDD CC AA u c v z s x k w Insert Arrangement 22-96 24-31 24-51 24-61 Service Rating II I I I Number of Contacts 7 31 47 4 61 Contact Size 12 for #10 WIRE 16 20 12 COAX 20 Contact Legend Symbol Contact Size HV

12 COAX

8 COAX

A Z Y X W V U T S R P N M L K J H G F E D C Ba z y x w vu t s r p n m q k j i h g f e d c b AA PP NN MM LL KK JJ HH GG FF EE DD CC BB a e C B D d f E g F i G h j m p n q r AABB bX t y Z Y A W V U T S R P N M L K J H z w k vx s u c F AD E BC Insert Arrangement 24-71 24-79 Service Rating N/A COAX Number of Contacts 45 2 2 1 5 Contact Size 20 16 8 COAX 20 8 COAX

Amphenol PT, SP, MS/PT Proprietary/MIL-DTL-26482, Series 1 bayonet coupling and solder termination Table 1: CONTACT DATA/CONNECTOR RATINGS Contact Specifications Contact Size Test Cur- rent Maximum Millivolt Drop† Solder Well Diameter Solder Well Depth 20 7.5 55 .046 +.004 .125 +.031 -.000 -.000 -.003 -.000 -.002 -.000 Amphenol® solder contact miniature cylindrical connectors meet the most critical application needs. Design versatility combined with high reliability performance makes these series of Miniature Cylindrical Connectors ideal for environmental sealing or pressurized applications. The MS/PT Series is qualified to MIL-DTL-26482, Series 1 and has all the outstanding design characteristics and quality of the PT Series. The SP Series is a modification of the PT, providing special shells with a wide mounting flange for back panel mounting. A corrosion resistant electrically conductive finish of cadmium plate with an olive drab chromate after-treatment is used on the PT and MS/PT. The SP is given a durable non-conductive hard anodic “Alumilite”® coating which provides abrasion protection and resistance to corrosion. NEW 500 hour corrosion resistance, RoHS compliant harsh environment conductive plating. Gray Zinc over an Electroless Nickel (Gray ZnNi) base, with a Light Gun Metal Gray appearance. Shell components for these series are aluminum. The dependable 5 key/keyway polarization with bayonet lock coupling assures positive mating with no chance of cross plugging. Spring tension provided by a wave washer in the coupling nut ensures maintenance of interfacial seal between mating halves. Both the insert and main joint gasket are molded from resilient neoprene. This provides excellent moisture sealing at the gasket and superior electrical isolation of the contact in the insert. Both pins and sockets are machined from a copper alloy and are gold plated. This gold plating eliminates contact corrosion and offers an indefinite shelf life. Socket contacts for these series are a closed entry design. A breakaway style plug is available in the PT solder series. Hermetics receptacles are available in PT and MS/ PT solder series. Receptacles with printed circuit board contacts are also available. PT Solder is UL recognized under file #E115497, Vol. 1, Sec. 5. The PT, SP and MS/PT Series are intermateable and intermountable with all existing Miniature Cylindrical Series connectors. Refer to pages 4-10 for insert arrangement availability. PT, SP, MS/PT Service Rating Service Rating Recommended Operating AC Voltage at Sea Level Test Voltage AC (RMS), 60 cps Sea Level 50,000 ft. 70,000 ft. 110,000 ft. I 600 1,500 500 375 200 II 1,000 2,300 750 500 200 † Silver plated wire per MIL-DTL-26482 * This connector style is sometimes referred to as a cable connecting “plug.” It does, however, mate with a straight or 90 degree plug. wall mounting receptacle cable connecting receptacle* box mounting receptacle straight plug jam nut receptacle thru bulkhead receptacle

“A” general duty “E” (SR), MS/”F” strain relief “E”, MS/”E” open wire seal “P” MS/ “P” potting boot “PG” cable gland seal PT, SP Service Classes PT and SP connectors are available in the service classes listed below. Each class, with the exception of hermetic, offers one or more means of terminating or supporting a cable or wire bundle. “A” General duty; back shell is threaded for conduit attachment of MS3057 cable clamp “A” (SR) General duty, with strain relief clamp for cable or wire bundle support “C” Pressurized receptacle; less than 1 cu. in. per hour leakage at 30 psi over a temperature range of –65°F to +257°F “E” Environmental resistant connectors - supplied with a multi-holed grommet and clamping nut for moisture-proofing individual open wires “E” (SR) Environmental resistant strain relief clamp and grommet for moisture proofing individual wires; provides added wire bundle support “P” Translucent nylon boot for retaining customer- applied potting compounds; held in place by a threaded ring “P” (SR) Strain relief clamp suitable for retaining customer applied potting compounds, with provision for wire support “PG” Compressing cable gland for moisture proofing jacketed cables. “H”* Hermetically sealed with compression glass inserts (see pages 22-25) Style with printed circuit board contacts- see page 20. MS/PT Service Classes The MS/PT Miniature connector is available in the following certified service classes: “E” Environmental resistant connectors - supplied with a multi-holed grommet and clamping nut for moisture-proofing individual open wires “F” Grommet seal with strain relief clamp “J” Compressing clamp and neoprene gland for moisture proofing multi-conductor jacketed cable and strain relief. Telescoping sleeves (MS 3420A) can be used to adapt to cables smaller than minimum close-down. “P” Translucent nylon boot for retaining customer- applied potting compounds; held in place by a threaded ring Amphenol PT, SP, MS/PT Proprietary/MIL-DTL-26482, Series 1 bayonet coupling and solder termination, cont.

PT00 (MS3110) SP00 wall mounting receptacle S S R (TP) R (TP) PT .120 ± .005 Dia. (.147 ± .005 Dia., size 24) SP .150 ± .005 Dia. L QM A K Z

4 Holes

Receptacle Front View Receptacle Side View Class “A”, “C” R (TP) S Max. A +.001 -.005 K +.020 -.010 L Max. M +.010 -.000 Q Thread Class 2A Z Max. D Min. L Max. N Max. V Thread Class APT SP PT SP PT SP PT SP PT SP Shell Size Class “A” (SR), “E” (SR), “P” (SR), MS/”F” Class “e”, C Thread D Min. G Max. H Max. L Max. N Max. L Max. N Max. D Min. L Max. N Max. D N Max. XL Max. B Thread L Max.Closed Free All dimensions for reference only. To complete part number see how to order on page 25. ■ (MMC) located within .0025 of (TP) N D VL .375 MIN G L C N D H L N N L D TERMINATION ASSEMBLIES “A” General Duty/ “C” Pressurized“ MS / “F” Strain Relief “E” Open Wire Seal “P” Potting Boot PT00A-XX-XXX SP00A-XX-XXX PT00C-XX-XXX PT00A-XX-XXX (SR) SP00A-XX-XXX (SR) PT00E-XX-XXX (SR) SP00E-XX-XXX (SR) PT00P-XX-XXX (SR) SP00P-XX-XXX (SR) MS3110F-XX-XXX PT00E-XX-XXX SP00E-XX-XXX MS3110E-XX-XXX PT00P-XX-XXX SP00P-XX-XXX MS3110P-XX-XXX PURCHASED RELEASED / Dec . 21 2015, 2:09:12 PM “PG” Cable Gland Seal PT00PG-XX-XXX ND L ND XL “J” Cable Seal MS3110J-XX-XXX

PT01 (MS3111) cable connecting receptacle S SY A K Z M L Q Shell Size Receptacle Front View Receptacle Side View Class “A”, “C” S ±.020 Y ±.020 A +.001 -.005 K +.020 -.010 L Max. M +.016 -.000 Q Thread Class 2A Z Max. D Min. L Max. N Max. V Thread Class A Shell Size Class “A” (SR), “E” (SR), “P” (SR), MS/”F” Class “e”, C Thread D Min. G Max. H Max. L Max. N Max. L Max. N Max. D Min. L Max. N Max. D N Max. XL Max. B Thread L Max.Closed Free Note: This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. To complete part number see how to order on page 25. All dimensions for reference only. N D .375 MIN VL G L C N D H L N N L D TERMINATION ASSEMBLIES “A” General Duty “A” (SR), “E” (SR), “P” (SR), MS / “F” Strain Relief “E” Open Wire Seal “P” Potting Boot PT01A-XX-XXX PT01A-XX-XXX (SR) PT01E-XX-XXX (SR) PT01P-XX-XXX (SR) MS3111F-XX-XXX PT01E-XX-XXX MS3111E-XX-XXX PT01P-XX-XXX MS3111P-XX-XXXX PURCHASED RELEASED / Dec . 21 2015, 2:09:12 PM “PG” Cable Gland Seal PT01PG-XX-XXX ND L ND XL “J” Cable Seal MS3116J-XX-XXX

PT02 (MS3112) SP02 box mounting receptacle S S R (TP) R (TP) PT .120 ± .005 Dia. (.147 ± .005 Dia., size 24) SP .150 ± .005 Dia. A N K Z L M To complete part number see how to order on page 25. ■ (MMC) located within .0025 of (TP) * The PT02 and SP02 box mounting receptacles are made only to complete a series; no provision is made for accessories or potting on the rear skirt. Shell Size Receptacle Front View Receptacle Side View R (TP) S A +.001 -.005 K +.020 -.010 L Max. M +.031 -.000 N Dia. Max. Z Max. PT SP PT SP PT SP PT SP PT SP All dimensions for reference only. PT02A-XX-XXX SP02A-XX-XXX * PT02C-XX-XXX * SP02C-XX-XXX * PT02E-XX-XXX * SP02E-XX-XXX MS3112E-XX-XXX * PT02P-XX-XXX * SP02P-XX-XXX MS3112P-XX-XXX

Class “A” (SR), “E” (SR), “P” (SR), MS/”F” Class “e”, C Thread D Min. G Max. H Max. L Max. N Max. L Max. N Max. D Min. L Max. N Max. D N Max. XL Max. B Thread L Max.Closed Free PT06 (MS3116) SP06 straight plug S To complete part number see how to order on page 25. Shell Size Plug Front View Plug Side View Class “A” S Max. J L Max. Q Thread Class 2A Z Max. D Min. L Max. N Max. V Thread Class A All dimensions for reference only. N D .375 MIN VL G L C N D H L N N L D TERMINATION ASSEMBLIES “A” General Duty “A” (SR), “E” (SR), “P” (SR), MS / “F” Strain Relief “E” Open Wire Seal “P” Potting Boot PT06A-XX-XXX SP06A-XX-XXX PTG06A-XX-XXX PT06A-XX-XXX (SR) SP06A-XX-XXX (SR) PTG06A-XX-XXX (SR) PT06E-XX-XXX (SR) SP06E-XX-XXX (SR) PTG06E-XX-XXX (SR) PT06P-XX-XXX (SR) SP06P-XX-XXX (SR) PTG06P-XX-XXX (SR) MS3116F-XX-XXX PT06E-XX-XXX SP06E-XX-XXX PTG06E-XX-XXX MS3116E-XX-XXX PT06P-XX-XXX SP06P-XX-XXX PTG06P-XX-XXX MS3116P-XX-XXX PURCHASED RELEASED / Dec . 21 2015, 2:09:12 PM “PG” Cable Gland Seal PT06PG-XX-XXX ND L ND XL “J” Cable Seal MS3116J-XX-XXX

PT07 (MS3114) SP07 jam nut receptacle S H S J A M Z R P K To complete part number see how to order on page 25. Shell Size Class “A” (SR), “E” (SR), “P” (SR), MS/”F” Class “E” (SR) Class “P”, MS/”P” C Thread D Max. G H L M C Thread D Max. G H L M D Max. L +.010 -.026 M N Z Shell Size Recept. Front View Receptacle Side View Class “E”, MS/”E” H ±.016 S A Dia. +.001 -.005 J Flat +.000 -.010 K +.011 -.010 M Panel Thickness R Thread Class 2A UNEF Z Max. L Max. M N Max. Z ±.040Min. Max. *Size 24 strain relief available in PT only All dimensions for reference only. J NA M Z R P L J A M Z CR P L G D H J A M Z R P L D N TERMINATION ASSEMBLIES MS / “F” Strain Relief “E” Open Wire Seal “P” Potting Boot “A” General Duty/ “C” Pressurized Receptacle PT07A-XX-XXX PT07C-XX-XXX PT07E-XX-XXX SP07E-XX-XXX MS3114E-XX-XXX PT07A-XX-XXX (SR) SP07A-XX-XXX (SR) PT07E-XX-XXX (SR) MS3114F-XX-XXX PT07P-XX-XXX MS3114P-XX-XXX

G Shell Size Plug Front View Plug Side View G Dia. Max B ±.031 C +.010 -.025 D ±.062 E +.047 -.025 L ±.057 A ±.025 H ±.015 K ±.015 L Max. All dimensions for reference only. D C B E L A H K L TERMINATION ASSEMBLIES“E” Open Wire Seal, “E” (SR) Strain Relief “P” Potting Boot 75 degrees PT08E-XX-XXX SP08E-XX-XXX PT08E-XX-XXX (SR) SP08E-XX-XXX (SR) PT08P-XX-XXX SP08P-XX-XXX To complete part number see how to order on page 25. All lockwire holes are .044 Dia. Min.

Printed Circuit Board Contacts Shell Size Part Number* PT02 with PCB Contacts Receptacle Front View Receptacle Side View R (TP) S +.011 -.010 A +.001 -.005 K +.021 -.010 L Max. M +.031 -.000 N Dia. Max. Z +.040 -.050 Box Mounting Receptacle (PT02) with PCB Contacts Order by applicable part number in chart below; add insert arrangement number. Refer to insert availability on pages 4-10. ■ (MMC) located within .0025 of (TP) All dimensions for reference only. Shell Size Part Number* PT07 with PCB Contacts Receptacle Front View Receptacle Side View H +.017 -.016 S ±.010 A Dia. +.001 -.005 J Flat +.000 -.010 K +.011 -.010 M ±.010 P Panel Thickness R Thread Class 2A Z +.025 -.035Min. Max. Jam Nut Receptacle (PT07) with PCB Contacts All lockwire holes are .044 Dia. Min. Order by applicable part number in chart below; add insert arrangement number. Refer to insert availability on pages 4-10. * For RoHS compliance connectors with PCB contacts change “71”- to: “FL” designates conductive gray zinc nickel plating “93” designates black zinc cobalt plating All dimensions for reference only.

S S R (TP) R (TP) PTB .120 ± .005 Dia. (.147 ± .005 Dia., size 24) SPB .150 ± .005 Dia. L M P A A K Receptacle Front View Receptacle Side View R (TP) S A +.001 -.005 K +.016 -.000 L ±.005 M +.010 -.000 P Max. PTB SPB PTB SPB PTB SPB * To complete part number add desired arrangement number (refer to pages 4 and 5 for insert availability) and add “PS”; Example: PTB-18-32PS. If a rotation is required, use PTB-18-32PS and add W, X, Y or Z. Example: PTB-18-32 PSW. The socket end of the insert always appears at the “P” dimension end of shell. ■(MMC) located within .0025 of (TP) All dimensions for reference only. * PTB-XX-XXX * SPB-XX-XXX

Three shell styles are available in the hermetic PT bayonet series:

• PTIH (MS3113H)
• PT02H
• PT07H (MS3114H) These hermetic connectors are only available with solder cup or flat eyelet pin contacts in the MS/PT version. Socket contacts are available in some proprietary PT versions. Other design characteristics of the PT hermetic connector series are as follows: Shell sizes: 8 through 24 (tin plated) Contact count: 2 through 61. Refer to pages 4 and 5 for insert availability for hermetics. Current: 5.0 amp each #20 contact 10 amp each #16 contact 17 amp each #12 contact Contacts are tin plated for PT; gold is optional Dielectric Withstanding Voltage (sea level): 1500 volts (RMS) 60 cps, Service Rating I 2300 volts (RMS) 60 cps, Service Rating II Compression glass inserts, permanently lettered Helium Leakage: Less than 1.0 X 10-6 cc/sec. at 15 psi differential Physical Shock: 100 G’s Vibration: Exceeds MIL-E-5272 Procedure II Thermal Shock: No deterioration or failure after 5 cycles at –55°F to +257°F Intermateability: Mates with MS3116 and PT06 Refer to pages 4-10 for insert arrangement availability. solder mounting receptacle box mounting receptacle jam nut receptacle

PTIH (MS3113H) hermetic solder mounting receptacle G A N WL Z.031 +.006 –.005 Shell Size Recept. Front View Receptacle Side View G Dia. Max. A Dia. +.001 -.005 L +.025 -.016 N Dia. +.001 -.005 W +.001 -.010 Z Max. To complete part number see how to order on page 25. * Solder cup pin contacts without interfacial seal ** Solder cup pin contacts with interfacial seal † Flat eyelet pin contacts without interfacial seal †† Flat eyelet pin contacts with interfacial seal All dimensions for reference only. * PTIH-XX-XXX PTIY-XX-XXX MS3113H-XXCXXX † PTIH-XX-XXX (100) †† PTIY-XX-XXX (100) †† MS3113H-XXYXXX

hermetic box mounting receptacle S S R (TP) R (TP) PT .120 ± .005 Dia. (.147 ± .005 Dia., size 24) SP .150 ± .005 Dia. A N WL ZU Recept. Front View Receptacle Side View R (TP) S ±.016 A Dia. +.001 -.005 K ±.015 L +.025 -.015 N Dia. +.001 -.005 U +.011 -.010 Z Max. To complete part number see how to order on page 25. * Solder cup pin contacts without interfacial seal ** Solder cup pin contacts with interfacial seal † Flat eyelet pin contacts without interfacial seal †† Flat eyelet pin contacts with interfacial seal ■ (MMC) located within .0025 of (TP) All dimensions for reference only. * PT02H-XX-XXX ** PT02Y-XX-XXX † PT02H-XX-XXX (100) †† PT02Y-XX-XXX (100)

PT07H (MS3114H) hermetic jam nut receptacle S H S A M Z R P K Shell Size Recept. Front View Receptacle Side View S ±.016 H Hex +.017 -.016 A +.001 -.005 K +.043 -.016 M +.031 -.000 P Panel Thickness R Thread Class 2A Z Max. Max. Min. To complete part number see how to order on page 25. * Solder cup pin contacts without interfacial seal ** Solder cup pin contacts with interfacial seal † Flat eyelet pin contacts without interfacial seal †† Flat eyelet pin contacts with interfacial seal All dimensions for reference only. * PT07H-XX-XXX PT07Y-XX-XXX MS3114H-XXCXXX † PT07H-XX-XXX (100) †† PT07Y-XX-XXX (100) †† MS3114H-XXYXXX

PT, SP, MS/PT how to order Connector Type Shell Style Service Class Shell Size Insert Arrangement Contact Configuration Insert Rotation Finish PT 00 A 20 41 P W 003 1. Connector Type PT standard olive drab, electrically conductive cadmium plate bayonet lock connector with solder contacts SP electrically non-conductive, hard anodic coated bay- onet lock connector with solder contacts and larger flange and mounting holes for back panel mounting PTG plug with grounding fingers 4. Shell Size Shell sizes 6 - 24 available 2. Shell Style

00 Wall mounting receptacle

01 Cable connecting receptacle

02 Box mounting receptacle

06 Straight plug

07 Jam nut receptacle

08 90 degree plug cable support B thru bulkhead receptacle (pressurized) I Solder mount receptacle (Hermetic only) 6. Contact Configuration P Pin contacts S Socket contacts For ordering connectors with printed circuit board contacts, see pg. 19. 3. Service Class A General duty back shell C Pressurized receptacle E Environmental resisting open wire seal with grom- met and nut P Assembly with potting boot PG Adapter for cable glad for moisture proofing jacketed cables H Hermetic* without interfacial seal Y Hermetic* with interfacial seal 7. Insert Rotation No letter is required for normal position W Refer to page 6 X Y Z 5. Insert Arrangement Refer to pages 4-10 for insert availability (Use only the number following the hyphen) 8. Finish SR Designates a strain relief clamp Indicate optional finishes as follows:

100 Suffix added for flat eyelet pin contacts in hermetic

005 * Anodic coating - Alumilite® (standard on “SP”) 023 * Electroless nickel 025 * Black zinc cobalt plating 072 * Conductive gray zinc nickel plating 424 * Electroless nickel finish with strain relief 470 * Black zinc cobalt plating with strain relief 725 * Gray zinc nickel plating with strain relief * RoHS Compliant finish Note: Olive drab cadmium is the default plating. If required on SP type use suffix (003). PT,SP Ex: PT00A-20-41PW003 Connector Type Specification Number Shell Style Service Class Shell Size Insert Arrangment Contact Configuration Insert Rotation MS 311 0 E 20 41 P W 1. Connector Type MS Military standard 5. Shell Size Shell sizes 8 - 24 available 3. Shell Style

0 Wall mounting receptacle

1 Cable connecting receptacle

2 Box mounting receptacle

3 Solder mount receptacle (Hermetic only)

4 Jam nut receptacle

6 Straight plug

1. Contact Configuration P Pin contacts S Socket contacts For ordering connectors with printed circuit board contacts, see pg. 19. 4. Service Class E Environmental resisting connector F Environmental resisting connectors with strain relief J Clamp assembly for moisture proofing multi-jacketed cables, with strain relief P Potted type with potting boot H Hermetic 8. Insert Rotation No letter is required for normal position W Refer to page 6 X Y Z MS/PT MIL-DTL-26482, Series 1 Ex: MS3110E20-41PW 2. Specification Number

311 Basic family number for

MIL-DTL-26482, Series 1 solder type 6. Insert Arrangement Refer to pages 4-10 for insert availability (Use only the number following the hyphen) Hermetic Version: In this version a letter replaces the hyphen between the Shell Size and Insert Arrangement (Steps 5 and 6) Y Flat eyelet pin contacts C Solder cup pin contacts * Hermetic connectors are supplied with tin plated shells. ** This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug.

Amphenol PT-SE, SP-SE, MS/PT-SE Proprietary/MIL-DTL-26482, Series 1 bayonet coupling and crimp termination Amphenol® SE crimp type miniature connectors provide performance and versatility needed for applications demanding high reliability and crimp removable contacts. These crimp contacts are rear insertable/front release and are held in position by an MS approved spring tower retention system. The MS/PT-SE Series is qualified to MIL-DTL-26482, Series 1 and has all the outstanding design characteristics and quality of the PT Series. The SP-SE Series is a modification of the PT-SE, providing special shells with a wide mounting flange for back panel mounting. A corrosion resistant electrically conductive finish of cadmium plate with an olive drab chromate after-treatment is used on the PT-SE and MS/PT-SE. The SP-SE is given a durable non-conductive hard anodic “Alumilite”® coating which provides abrasion protection and resistance to corrosion. 500 hour corrosion resistance, RoHS compliant harsh environment conductive plating. Gray Zinc over an Electroless Nickel (Gray ZnNi) base, with a Light Gun Metal Gray appearance. Shell components for these series are aluminum. The dependable 5 key/ keyway polarization with bayonet lock coupling assures positive mating with no chance of cross plugging. Spring tension provided by a wave washer in the coupling nut ensures maintenance of interfacial seal between mating halves. Both the insert and main joint gasket are molded from resilient neoprene. This provides excellent moisture sealing at the gasket and superior electrical isolation of the contact in the insert. Both pins and sockets are machined from a copper alloy and are gold plated. This gold plating eliminates contact corrosion and offers an indefinite shelf life. Socket contacts for these series are closed entry design. Breakaway style plug is available in PT-SE crimp. The PT-SE, SP-SE and MS/PT-SE Series are intermateable and intermountable with all existing Miniature Cylindrical Series connectors. Refer to pages 4-10 for insert arrangement availability. * This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. wall mounting receptacle cable connecting receptacle* box mounting receptacle straight plug jam nut receptacle

“SE”, MS / “E” open wire seal “SE” (SR), MS / “F” strain relief clamp “SP”, MS / “P” potting boot PT-SE, SP-SE, MS/PT-SE Contact Specifications Contact Size Test Current Maximum Millivolt Drop† Crimp Well Diameter Minimum Well Depth 20 7.5 55 .049±.001 .267 16 13.0 49 .067±.001 .236 12 23.0 42 .100±.002 .236 Service Rating Service Rating Recommended Operating AC Voltage at Sea Level Test Voltage AC (RMS), 60 cps Sea Level 50,000 ft. 70,000 ft. 110,000 ft. I 600 1,500 500 375 200 II 1,000 2,300 750 500 200 † Silver plated wire per MIL-DTL-26482 PT-SE and SP-SE Service Classes PT-SE and SP-SE connectors are available in the three service classes listed below. “SE” Open wire sealing - environmental resistant, with a nut and grommet for moisture proofing individual wires “SE (SR)“ Strain relief clamp - environmental resistant strain relief clamp and grommet for moisture proofing individual wires; provides added wire bundle support “SP” Translucent nylon boot for retaining customer applied potting compounds; held in place by a threaded ring MS/PT-SE Service Classes MS-SE series connectors are available in the following certified service classes: “E” Open wire sealing - environmental resisting connectors are supplied with a multi-hole grommet and clamping nut for moisture proofing individual open wires “F” Environmental resistant strain relief clamp and grommet for moisture proofing individual wires; provides added wire bundle support “P” Potting applications - these connectors are supplied with a translucent nylon boot for retention of customer applied potting compound

PT00 SE (MS3120) SP00 SE wall mounting receptacle S S R (TP) R (TP) T Dia. Receptacle Front View Receptacle Side View R (TP) S Max. T Dia. ±.005 A Dia. +.001 -.005 K ±.016 M +.010 -.000 Panel Thickness PT SP PT SP PT SP PT SP PT SP Shell Size Class “SE”, MS/”E” Class “SE”(SR), MS/”F” Class “SP”, MS/”P” L Max. N Dia. Max G Dia. L Max. N Max. D Dia. Max. L Max. N Dia. Max. * Back panel mounting All dimensions for reference only. To complete part number see how to order on page 36. ■(MMC) located within .005 of (TP) A M K N L “SE” Open Wire Seal “SE” (SR), MS / “F” Strain Relief “SP” Potting Boot PT00SE-XX-XXX SP00SE-XX-XXX MS3120E-XX-XXX PT00SE-XX-XXX (SR) SP00SE-XX-XXX (SR) MS3120F-XX-XXX PT00SP-XX-XXX SP00SP-XX-XXX TERMINATION ASSEMBLIES

MF00 SE (MS3128) wall mounting receptacle S S R (TP) R/one.superior (TP) R (TP) R/one.superior (TP) T Dia. T/one.superior Dia. Receptacle Front View Receptacle Side View R R1 S Max. T Dia. ±.005 T1 Dia. ±.005 A Dia. +.001 -.000 K ±.016 M +.010 -.000 Class MS/ ”E” Class MS/ “F” L Max. N Max. F Min. G Dia. L Max. N Max. All dimensions for reference only. M K NA L TERMINATION ASSEMBLIES“SE” Open Wire Seal MS / “F” Strain Relief MF00SE-XX-XXX MS3128E-XX-XXX MF00SE-XX-XXX (SR) MS3128F-XX-XXX

PT01 SE (MS3121) SP01 SE cable connecting receptacle S S Shell Size Receptacle Front View Receptacle Side View S Max. Class “SE”, MS/ ”E” Class “SE” (SR), MS/”F” Class “SP”, MS/”P” A Dia. +.001 -.005 K ±.018 L Max. N Dia. Max. G Dia. L Max. N Max. D Dia. L Max. N Dia. Max. Note: This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. To complete part number see how to order on page 36. All dimensions for reference only. K K NA L A L D N K “SE” Open Wire Seal “SE” (SR), MS / “F” Strain Relief “SP”, MS / “P” Potting Boot TERMINATION ASSEMBLIES PT01SE-XX-XXX SP01SE-XX-XXX MS3121E-XX-XXX PT01SE-XX-XXX (SR) SP01SE-XX-XXX (SR) MS3121F-XX-XXX PT01SP-XX-XXX SP01SP-XX-XXX MS3121P-XX-XXX

PT02 SE (MS3122) SP02 SE box mounting receptacle S S R (TP) R (TP) T Dia. L K M A N D To complete part number see how to order on page 36. ■ (MMC) located within .0025 of (TP) Shell Size Receptacle Front View Receptacle Side View R S Max. T Dia. ±.005 A Dia. +.001 -.005 D Max. K ±.025 L Max. M +.010 -.000 N Dia. +.011 -.000PT SP PT SP PT SP PT SP PT SP All dimensions for reference only. PT02SE-XX-XXX SP02SE-XX-XXX MS3122E-XX-XXX

MF02 SE (MS3127) box mounting receptacle S S R (TP) R/one.superior (TP) R (TP) R/one.superior (TP) T Dia. L K M A N D T/one.superior Dia. Receptacle Front View Receptacle Side View N Dia. +.011 -.000 R R1 S Max. T ±.005 ±.005 A Dia.+.001 -.005 D Max. K ±.016 L Max. M +.010 -.000 To complete part number see how to order on page 36. ■ (MMC) located within .0025 of (TP) All dimensions for reference only. MF02SE-XX-XXX MS3127E-XX-XXX

PT06 SE (MS3126) SP06 SE straight plug S To complete part number see how to order on page 36. Shell Size Plug Front View Plug Side View S Dia. Max. Z ±.045 ±.045 Class “SE”, MS/”E” Class “SE” (SR), MS/”F” Class “SP”, MS/”P” L Max. N Max. G Dia. L Max. N Max. D Dia. L Max. N Dia. Max. * PT-SE, MS-SE and MS-SP only. All dimensions for reference only. L N Z pin contacts Z/one.superior socket contacts L ND Z pin contacts Z/one.superior socket contacts L NG Z pin contacts Z/one.superior socket contacts “SE”, MS / “E” Open Wire Seal “SE” (SR), MS / “F” Strain Relief “SP”, MS / “P” Potting Boot TERMINATION ASSEMBLIES PT06SE-XX-XXX SP06SE-XX-XXX PTG06SE-XX-XXX MS3126E-XX-XXX PT06SE-XX-XXX (SR) SP06SE-XX-XXX (SR) PTG06SE-XX-XXX (SR) MS3126F-XX-XXX PT06SP-XX-XXX SP06SP-XX-XXX PTG06SP-XX-XXX MS3126P-XX-XXX

PT07 SE (MS3124) SP07 SE jam nut receptacle S H S Shell Size Receptacle Front View Receptacle Side View H Hex Max. S Max. A Dia. +.001 -.005 J Flat +.000 -.010 K +.011 -.010 M ±.005 P Panel Thickness R Thread Class 2AMin. Max. Shell Size Class “SE”, MS/”E” Class “SE” (SR), MS/”F” Class “SP”, MS/”P” L Max. N Max. F Min. G Dia. Free L Max. N Max. G Dia. L Max. N Dia. Max. All dimensions for reference only. J NA M K P R L J NFA M R P K L J NGA R M L P K “SE”, MS / “E” Open Wire Seal “SE” (SR), MS / “F” Strain Relief “SP”, MS / “P” Potting Boot TERMINATION ASSEMBLIES PT07SE-XX-XXX SP07SE-XX-XXX MS3124E-XX-XXX PT07SE-XX-XXX (SR) SP07SE-XX-XXX (SR) MS3124F-XX-XXX PT07SP-XX-XXX SP07SP-XX-XXX MS3124P-XX-XXX To complete part number see how to order on page 36. All lockwire holes are .044 Dia. Min.

To complete part number see how to order on page 36. All lockwire holes are .044 Dia. Min. Shell Size Plug Front View Plug Side View G Dia. Max. B ±.031 C +.010 -.025 D ±.062 E +.047 -.025 L Max. A ±.025 H ±.015 K ±.015 L Max. All dimensions for reference only. D C B E L A H K L “SE” Open Wire Seal, “SE” (SR) Strain Relief “SP” Potting Boot 75 degreesTERMINATION ASSEMBLIES PT08SE-XX-XXX SP08SE-XX-XXX PT08SE-XX-XXX (SR) SP08SE-XX-XXX (SR) PT08SP-XX-XXX SP08SP-XX-XXX

PT-SE, SP-SE, MS/PT-SE how to order Connector Type Shell Style Service Class Shell Size Insert Arrangement Contact Configuration Insert Rotation Finish PT 00 SE 20 41 P W 003 1. Connector Type PT standard olive drab, electrically conductive cadmium plate bayonet lock connector with solder contacts MF standard olive drab, electrically conductive cadmium plated, bayonet lock connector with dual mounting holes, and crimp contacts SP electrically non-conductive, hard anodic coated bay- onet lock connector with solder contacts and larger flange and mounting holes for back panel mounting 4. Shell Size Shell sizes 8 - 24 available 2. Shell Style

1. Contact Configuration P Pin contacts S Socket contacts 3. Service Class SE Environmental crimp SP potted type crimp Both of the above are Amphenol proprietary versions of the MILDTL-26482, Series 1 crimp contact connector and offer 15 lbs. contact retention for size 20 contacts; 25 lbs. for size 16 contacts. PG adapter for cable gland for moisture proofing jacketed cables SQ Braided shield termination G Heatshrink termination 7. Insert Rotation No letter is required for normal position W Refer to page 6 X Y Z 5. Insert Arrangement Refer to pages 4-10 for insert availability (Use only the number following the hyphen) PT-SE, SP-SE Ex: PT00SE-20-41PW003 Connector Type Specification Number Shell Style Service Class Shell Size Insert Arrangement Contact Configuration Insert Rotation MS 311 0 E 20 41 P W 1. Connector Type MS Military standard 5. Shell Size Shell sizes 8 - 24 available 3. Shell Style

1 Cable connecting receptacle*

7 box mounting receptacle with dual mounting holes 8 wall mounting receptacle with dual mounting holes 7. Contact Configuration P Pin contacts S Socket contacts 4. Service Class E Environmental resisting connector F Environmental resisting connectors with strain relief P Potted type with potting boot SQ Braided shield termination G Heatshrink termination 8. Insert Rotation No letter is required for normal position W Refer to page 6 X Y Z MS/PT-SE MIL-DTL-26482, Series 1 Ex: MS3120E20-41PW 2. Specification Number 312 basic family for MIL-DTL-26482, Series 1 crimp type 6. Insert Arrangement Refer to pages 4-10 for insert availability (Use only the number following the hyphen) * This connector style is sometimes referred to as a cable connecting “plug”. It does, however, mate with either a straight or 90 degree plug. 8. Finish SR Designates a strain relief clamp Indicate optional finishes as follows: 005 * Anodic coating - Alumilite® (standard on “SP”) 023 * Electroless nickel 025 * Black zinc cobalt plating 072 * Conductive gray zinc nickel plating 424 * Electroless nickel finish with strain relief 470 * Black zinc cobalt plating with strain relief 725 * Gray zinc nickel plating with strain relief * RoHS Compliant finish Note: Olive drab cadmium is the default plating. If required on SP type use suffix (003).

PT & SP accessories – sealing plugs, flange gaskets, potting boots B DIA A DIA C .135 +.030 –.025 .130 DIA SIZE 6 TO 22 .156 DIA SIZE 24 .160 DIA 10-150949 T 15º REF B L D E Contact Size Amphenol® Part Number MS Number A Dia. ±.010 B Dia. ±.005 C ±.010 Color Code 12 10-405996-12 MS27488-12 .121 .171 .564 Yellow 16 10-405996-16 MS27488-16 .083 .133 .564 Blue 20 10-405996-16 MS27488-20 .060 .090 .564 Red SEALING PLUGS- FOR PT & SP How to Order: Order by 10- (Proprietary) or MS part number as shown in chart above. Shell Size PT 10-101949 SP 10-150949 PT & SP 10-101949 10-150949 R ±.010 S ±.010 R ±.010 S ±.010 F +.016 -.000 T ±.008 MOUNTING FLANGE GASKETS – FOR PT & SP How to Order: For PT: 10-101949-XX (complete order number with desired shell size). For SP: 10-150949-XX (complete order number with desired shell size). Shell Size B Max. D ±.015 E ±.015 L Max. 8 .433 .312 .438 .766 10 .493 .438 .562 .830 12 .552 .516 .688 .861 14 .643 .625 .781 .916 16 .658 .656 .890 .936 18 .689 .703 1.000 .959 20 .750 .766 1.125 1.052 22 .794 .812 1.234 1.073 24 1.070 .918 1.374 1.310 75° POTTING BOOTS – FOR PT & SP How to Order: 10-101988-XX (complete order number with desired shell size). All dimensions for reference only SEALING PLUG MS27488-XX 10-405996-XX MOUNTING FLANGE GASKET 10-101949-XX 10-150949-XX 75° POTTING BOOT 10-101988-XX

PT & SP accessories – clamps B D G L C B D G L C C B A V Thread Shell Size B Max. C Thread Class 2B D Min. G Max. L Max. 8 .550 6-32 NC .240 .812 .930 10 .675 6-32 NC .302 .875 .930 12 .803 6-32 NC .428 1.000 .930 14 .920 6-32 NC .552 1.125 .930 16 1.047 6-32 NC .615 1.188 1.062 18 1.165 8-32 NC .740 1.438 1.062 20 1.291 8-32 NC .740 1.438 1.093 22 1.418 8-32 NC .928 1.719 1.093 24 1.533 8-32 NC .928 1.719 1.093 How to Order: 10-101971-XX X Add desired Add desired finish suffix† shell size “3” designates olive drab cadmium “5’ designates Alumilite® Not for use with jam nut style connectors CLASS “E” STRAIN RELIEF CLAMP – FOR PT & SP Shell Size B Max. C Thread Class 2B D Min. G Max. L +.010 -.020 8 .540 6-32 NC .240 .812 .843 10 .665 6-32 NC .302 .875 .843 12 .793 6-32 NC .428 1.000 .843 14 .910 6-32 NC .552 1.125 .843 16 1.037 6-32 NC .614 1.188 .975 18 1.155 8-32 NC .740 1.438 .975 20 1.281 8-32 NC .740 1.438 1.007 22 1.408 8-32 NC .928 1.719 1.007 24 1.533 8-32 NC .938 1.719 1.007 CLASSES “A” & “P” STRAIN RELIEF CLAMP – FOR PT & SP How to Order: 10-101980-XX X Add desired Add desired finish suffix† shell size “3” designates olive drab cadmium “5’ designates Alumilite® Not for use with jam nut style connectors Shell Size Amphenol® Part Number A ±.031 B Max. C Dia. Min. V Thread 10 97-3057-1004 .795 .842 .3125 .6250-24 12 97-3057-1007 .850 .995 .4375 .7500-20 14 97-3057-1008 .920 1.120 .5625 .8750-20 16 97-3057-1010 .920 1.216 .6250 1.0000-20 18/20 97-3057-1012 .927 1.403 .7500 1.1875-18 22/24 97-3057-1016 1.015 1.683 .9375 1.4375-18 CLASS “A” CABLE CLAMPS – FOR PT & SP How to Order: Order by 97-3057-XXXX number listed above. Standard finish is olive drab zinc alloy. Consult Amphenol, Sidney, NY for alternate finishes. † Standard accessory finishes are “3” olive drab cadmium for PT and MS/PT types, “5” Alumilite® for SP types. Electroless nickel plating is also available on some items; consult Amphenol, Sidney, NY All dimensions for reference only. CLASS “E” STRAIN RELIEF CLAMP 10-101971-XX RELIEF CLAMP 10-101980-XX CLASS “A” CABLE CLAMP 97-3057-XXXX

B Dia. +.010 -.000 C Dia. +.010 -.000 G Dia. Max. L +.020 -.000 X Std. & MS RA, CA, NA X MS only RAL/CAL/NAL PT, SP, MS/PT accessories – protection caps G L .140 +.010 B X X C N L .140 +.010 –.005DIA FOR SIZE 24 .125 +.010 –.005DIA FOR SIZE 6-22 RECEPTACLE PROTECTION CAPS – FOR PT, SP, MS/PT How to Order Proprietary Receptacle Caps: Wall Receptacle Caps: 10-101960- XX X Cable Connecting Receptacle Caps: 10-101961- XX X Jam Nut Receptacle Caps: 10-101964- XX X Add desired shell size Add desired finish suffix† “FL” designates gray zinc nickel “3” designates olive drab cadmium “5” designates Alumilite® Proprietary caps are supplied with standard bead chains only (as shown in drawing at left). For other chain options, an MS version cap should be ordered. How to Order MS Version Receptacle Caps: Wall Receptacle Caps: MS3181- XX -CA for sash chain -CAL for long sash chain -RA for rope chain -RAL for long rope chain Jam Nut Recept. Caps: MS3181- XX -NA for sash chain -NAL for long sash chain Shell size MS versions are supplied with standard anodize finish only. For other finish options a proprietary cap should be ordered. PLUG PROTECTION CAPS – FOR PT, SP, MS/PT Shell Size N Dia. +.001 -.005 L Dia. +.025 -.015 X Std. & MS CA, RA X MS only CAL/ RAL 6 .348 .532 3.000 5.000 8 .473 .532 3.000 5.000 10 .590 .532 3.000 5.000 12 .750 .532 3.500 5.000 14 .875 .532 3.500 5.000 16 1.000 .532 3.500 5.000 18 1.125 .532 3.500 5.000 20 1.250 .594 4.000 5.000 22 1.375 .594 4.000 5.000 24 1.500 .627 4.000 5.000 How to Order Proprietary Plug Caps: 10-101957-XX X Add desired shell size Add desired finish suffix† “FL” designates gray zinc nickel “3” designates olive drab cadmium “5” designates Alumilite® Proprietary caps are supplied with standard bead chains only (as shown in drawing at left). For other chain options an MS version cap should be ordered. How to Order MS Version Plug Caps: MS3180- XX -CA for sash chain -CAL for long sash chain -RA for rope chain Shell Size -RAL for long rope chain RECEPTACLE PROTECTION CAP FOR PT, SP, MS/PT CONNECTORS 10-101960-XXX MS3181-XXX (Wall Receptacle) 10-101961-XXX (Cable Connecting Receptacle) 10-101964-XXX MS3181-XXX (Jam Nut Recptacle) PLUG PROTECTION CAP FOR PT, SP, MS/PT CONNECTORS MS3180-XXX 10-101957-XXX

PT & SP accessories – dummy receptacles, “O” rings, plastic dust caps S SR R .150 DIA. +.004 –.0024 HOLES N M K Shell Size K ±.010 M +.030 -.000 N +.001 -.005 Proprietary Version MS Version R ±.005 S ±.010 (TP) (TP) DUMMY RECEPTACLES – FOR PT, SP, MS/PT How to Order Proprietary Dummy Receptacles: 10-150921-XX X Add desired shell size Add desired finish suffix† “FL” designates gray zinc nickel “3” designates olive drab cadmium “5” designates Alumilite® How to Order MS Version Dummy Receptacles: MS3115-XX X Add desired shell size Add desired finish suffix† -A designates Alumilite® -L designates electroless nickel -W designates olive drab cadmium PLASTIC DUST CAPS – FOR PT, SP Shell Size Plug Plastic Dust Cap Receptacle Plastic Dust Cap 6 10-70500-8 10-70506-8S 8 10-70506-12 10-70506-10 10 10-70500-12 10-70506-12 12 10-70506-16 10-70506-14 14 10-70506-18 10-70506-16 16 10-70506-20 10-70506-18 18 10-70506-22 10-70506-20 20 10-70506-24 10-79506-22 22 10-70524-1 10-70506-24 24 10-70506-28 10-70524-1 How to Order Plastic Dust Caps: To the basic order number add the dust cap size to match connector plug or receptacle shell size, as shown in the tables above. Example: 10-70506-12 would be the correct order number for a plastic dust cap for a PT00 receptacle, shell size 10. All dimensions for reference only. DUMMY RECEPTACLE FOR PT, SP, MS/PT CONNECTORS MS3115-XXX 10-150921-XXX

DUMMY RECEPTACLES – FOR PT, SP, MS/PT PT accessories glands Nylon Cable Glands Material: Nylon 66 (UL Approved 94V-2) Seal ring: UL 94V-2 (UL Approved 94V-2) Thread Type: Metric; PG, NPT Temp Range: Static: -40° to +100°C Dynamic: -20° to +80°C Short Term: +120° Current Colors: Gray, Black AIO Part Thread “A” M “d” (mm) Cable Range (mm) Thread “L” (mm) Clamp “H” (mm) Spanner “S” (mm) AIO-CSM12 M12 x1.5 8 3-6.5 8 20 15 AIO-CSM16 M16 x 1.5 8 4-8 8 22 19 AIO-CSM18 M18 x 1.5 10 5-10 9 25 22 AIO-CSM20 M20 x 1.5 12 6-12 9 30 24 AIO-CSM22 M22 x 1.5 14 10-14 10 30 27 AIO-CSM24 M24 x 1.5 14 10-14 10 30 27 AIO-CSM25 M25 x 1.5 18 13-18 10 30 33 AIO-CSM30 M30 x 2.0 18 13-18 11 33 33 AIO-CSM32 M32 x 1.5 25 18-25 11 38 42 AIO-CSM33 M33 x 2.0 25 18-25 11 39 42 AIO-CSM40 M40 x 1.5 32 22-32 13 48 54 AIO-CSM50 M50 x 1.5 38 32-38 14 50 60 AIO-CSM72 M72 x 2.0 57 51-57 16 75 80 AIO-CSIN1/2 NPT1/2” 12 6-12 13.6 28 24 AIO-CSIN3/4 NPT 3/4” 18 13-18 14.1 32 33 AIO-CSIN3/2 NPT 1”1/2” 32 22-32 17.3 50 54 AIO-CSGIN1/2 G 1/2” 12 6-12 9 26 24 AIO-CSGIN3/4 G 3/4” 18 13-18 11 27 33 AIO-CSGIN1 G1” 25 18-25 11 33 42 AIO-CSGIN5/4 G1”1/4 28 21-28 13 48 54 AIO-CSGIN3/2 G1”1/2” 32 22-32 13 48 54 AIO-CSGIN5/2 G2”1/2” 57 51-57 14 75 80 AIO-CSPG7 PG7 6.5 3-6.5 8 20 15 AIO-CSPG9 PG9 8 4-8 8 22 19 AIO-CSPG11 PG11 10 5-10 8 24 22 AIO-CSPG13.5 PG13.5 12 6-12 9 26 24 AIO-CSPG16 PG16 14 10-14 10 28 27 AIO-CSPG21 PG21 18 13-18 11 33 33 AIO-CSPG29 PG29 25 18-25 11 38 42 AIO-CSPG36 PG36 32 22-32 13 48 54 AIO-CSPG42 PG42 38 32-38 14 52 60 For additional information on other products available refer to our Cord grips & Cable Glands, Catalog 12-055 Metal Cable Glands Material: Brass with Nickel; Brass with Tin/Nickel Clamping: UL approved PA6, 94V-0 Seal Ring: UL 94V-2 (UL approved NBR, 94V-2;UL approved DOW CORNING RUBBER, 94V-0 Thread Type: Metric, PG, NPT Protective: IP68 (tighten with o-ring) Temp Range: -40° to +100°C Torque Value (N-M) of hex and cap nuts: 3.0-4.5 N-M M12, M16, M20 are UL recognized under file #E339605 AIO Part Thread “A” M “d” (mm) Cable Range (mm) Thread “L” (mm) Clamp “H” (mm) Spanner “S” (mm) AIO-CSJM12 M12x1.5 6.5 3-6.5 6.2 15 14 AIO-CSJM14 M14x1.5 8 4-8 5 19 15 AIO-CSJM16 M16x1.5 9 6-9 6.3 20 18 AIO-CSJM18 M18x1.5 10 5-10 7 20 22 AIO-CSJM20 M20x1.5 12 6-12 8.3 20 22 AIO-CSJM22 M22x1.5 14 10-14 8 24 24 AIO-CSJM24 M24x1.5 14 10-14 8 24 27 AIO-CSJM25 M25x1.5 18 13-18 7.8 23 30 AIO-CSJM27 M27x1.5 18 13-18 8 26 30 AIO-CSJM30 M30x2.0 18 13-18 8 26 32 AIO-CSJM32 M32x1.5 25 18-25 10 27 40 AIO-CSJM36 M36x2.0 25 18-25 10 34 40 AIO-CSJM40 M40x1.5 32 22-32 10 39 50 AIO-CSJM50 M50x1.5 38 32-38 11 39 60 AIO-CSJM63 M63x1.5 44 37-44 12 43 67 AIO-CSJM72 M72x1.5 52 46-52 16 47 75 AIO-CSJM80 M80x2.0 60 52-60 20 57 90 AIO-CSJM90 M90x2.0 70 62-70 20 57 100 AIO-CSJIN1/2 NPT 1/2” 12 6-12 13.6 25 24 AIO-CSJIN3/4 NPT 3/4” 18 13-18 14.1 26 30 AIO-CSJIN5/4 NPT 1”1/4” 32 22-32 17.3 41 50 AIO-CSJIN3/2 NPT 1”1/2” 32 22-32 17.3 46 50 AIO-CSJIN2 NPT2” 44 37-44 17.7 46 65 AIO-CSJIN5/2 NPT2 1/2” 52 46-52 23.7 58 80 AIO-CSJIN3 NPT3” 70 62-70 26 58 100 AIO-CSJGIN1/2 G1/2” 12 6-12 8 24 24 AIO-CSJGIN3/4 G3/4” 18 13-18 8 27 30 AIO-CSJGIN1 G1” 25 18-25 10 34 40 AIO-CSJGIN5/4 G1”1/4” 32 22-32 10 39 50 AIO-CSJGIN3/2 G1”1/2” 32 22-32 10 39 50 AIO-CSJGIN2 G2” 44 37-44 12 44 65 AIO-CSJGIN 5/2 G2 1/2” 52 46-52 16 47 82 AIO-CSJPG7 PG7 6.5 3-6.5 6 18 14 AIO-CSJPG9 PG9 8 4-8 7 21 18 AIO-CSJPG11 PG11 10 5-10 7 20 22 AIO-CSJPG13.5 PG13.5 12 6-12 8 24 22 AIO-CSJPG16 PG16 14 10-14 8 25 24 AIO-CSJPG21 PG21 18 13-18 8 26 30 AIO-CSJPG36 PG36 32 22-32 10 38 50 AIO-CSJPG42 PG42 38 32-38 11 42 60 AIO-CSJPG48 PG48 44 37-44 12 44 65

“SE” The following data includes information pertaining to the application tools for crimping, inserting and removing size 20, 16, and 12 contacts incorporated in Amphenol® Miniature Cylindrical Connectors. All crimping tools included are the “full cycling” type, and when used as specified by the manufacturer, provide reliable crimped wire to contact termination. Tool frames and turret heads are available from approved tool manufacturers; consult Amphenol, Sidney, NY for listings. Assembly instructions are available online at www.amphenol-industrial.com See the following: L-786 for SE assembly instructions L-555 for solder type instructions CRIMPING TOOLS FOR PT-SE, SP-SE, MS/PT-SE (MIL-DTL-26482, Series 1) Connectors Contact Size MS Tool Part Number Tool From Turret Head

20 M22520/1-01 M22520/1-02

16 M22520/1-01 M22520/1-02

12 M22520/1-01 M22520/1-02

FOR PT-SE, SP-SE, MS/PT-SE (MIL-DTL-26482, Series 1) Connectors Contact Size Insertion Tool Removal Tool Amphenol® Contact Insertion Pliers Amphenol® Contact Insertion Tool MS Part Number Con- tact Insertion Tool Amphenol® Contact Removal Tool MS Part Number Contact Removal Tool 20 11-8107-20 11-7401-20 M81969/17-03 11-7880-20 M81969/19-07 16 11-8107-16 11-7401-16 M81969/17-04 11-7880-16 M81969/19-08 12 - - M81969/17-05 - M81969/19-09

Contacts - Power and Thermocouple Crimp for miniature cylindrical connectors The following tables provide part number information for crimp contacts used in Amphenol® Miniature Cylindrical Connectors. For additional information, consult Amphenol, Sidney, NY. CRIMP CONTACTS for MIL-DTL-26482, Series 1 (PT-SE, SP-SE) Connectors Contact Size Accommodates Wire Size Pins Sockets MS Number Amphenol® Proprietary Number MS Number Amphenol® Proprietary Number 20 20, 22 & 24 AWG M39029/31-240 10-683787-20P M39029/32-259 10-731210-3D1 16 16, 18 & 20 AWG M39029/31-228 10-683788-16P M39029/32-247 10-679379-16D 12 12 & 14 AWG M39029/31-235 10-807100-125 M39029/32-254 10-807103-125 20-16 16 AWG 10-330930-20F 10-807155-205 16-20 20 AWG 10-330932-16F 10-330933-16F 12-10 12 AWG 10-330938-12F 10-330939-12F THERMOCOUPLE CONTACTS for Miniature Connectors Size Material Pins Proprietary Part Number Sockets Proprietary Part Number SE SE

16 Crimp Termination

Chromel 10-330940-21P 10-330940-21S Alumel 10-330940-22P 10-330940-22S

20 Crimp Termination

Chromel 10-330940-1P 10-330940-1S Alumel 10-330940-2P 10-330940-2S Iron 10-330940-3P 10-330940-3S Constantan 10-330940-4P 10-330940-4S See L-776 for thermocouple contact termination instructions. These are online at www.amphenol-industrial.com For PCB contacts for miniature connectors, see page 20.

for miniature cylindrical connectors Amphenol® Miniature Connectors can incorporate shielded coax contacts. The Miniature family is built around MIL-DTL-26482 specifications, with Mil-approved and proprietary styles offered. Normal operating voltage for Miniature cylindricals with power only contacts is up to 1,000 VAC (RMS) at sea level. Table 1: Miniature Cylindricals offer these features for contact termination flexibility:

• Several insert arrangements that can incorporate:
• Size 8 & 12 Crimp Coax contacts for Crimp type
• Size 8 & 12 Solder Coax contacts for Solder type
• Wide selection of connector shell styles and sizes
• Standard power contact options within the various connector styles include: solder type, crimp front release, crimp rear release
• Coax contacts are designed to the same high performance standards as power contacts. Coax and power contacts may be intermixed with no degradation of connector reliability.
• No mis-mating or cross-plugging with insert rotation and keyway polarization. Table 2: GENERAL ORDERING INFORMATION Amphenol Miniature Cylindricals are normally supplied with a full complement of power contacts, separately packaged. Coax contacts are ordered by part number as referenced in the part number charts on the following pages of this catalog, and are substituted for the power contacts at the time of the cable or equipment assembly. If the application is for coax only, the connector may be ordered less contacts and no power contacts will be supplied. Installation instructions for the coax contacts for Miniature Connectors are provided in Amphenol documents as follows: L-633 for solder type; L-613 for SE type. HOW TO ORDER: A. Select the coax contacts designed for the cable being used from the applicable charts in this catalog for each Miniature type (solder, SE). B. Select a connector insert from those shown on pages 4-5 which will accommodate the quantity and size of coaxial contacts needed plus any power contacts required. Note: Size 8S and 12S contacts are used with connector inserts through shell size 18 only. For larger connector shell sizes, use size 8L contacts. C. Determine the Miniature Cylindrical type, shell style, finish, service class and insert rotation required for your application. D. Consult Amphenol, Sidney NY with the pertinent cable, contact, insert arrangement and connector style choices for complete connector part number. Solder Coax Contact for use in Miniature Solder Type Connectors Pin Crimp Coax Contact for use in Miniature Crimp SE Type Connectors Socket Crimp Coax Contact for use in Miniature Crimp SE Type Connectors

for miniature cylindrical connectors, cont. Amphenol® Coaxial Contacts designed for use in Miniature Cylindrical Connectors offer the same durability advantages and design benefits for reliable interconnection as the Amphenol coax contacts used in high performance D38999 connectors. A variety of military and commercial shielded cables are accommodated within the miniature cylindrical series. Amphenol supplies coax contacts for solder and crimp SE connector styles. Other features of the coax for miniature cylindricals include:

• Miniature coax design has an outside nut within the assembly for fast, reliable assembly of contact to cable.
• All types feature solder style inner contacts and crimp style outer contacts for reliable cable termination
• Miniature coax crimp type contacts are designed for use in Miniature crimp series connectors
• Miniature coax solder type contacts are designed for use in Miniature solder series connectors. These come pre-installed into the solder connector. TYPICAL ELECTRICAL PERFORMANCE Size 8 and 12 Coax Contacts Contact Resistance: Center @ 1 Amp, 170 millivolts max. voltage drop @ 25°C Outer @ 12 Amps, 150 millivolts max. voltage drop @ 25°C Dielectric Withstanding Voltage: Size 8: 1,300 VAC Rms @ sea level Size 12: 1,000 VAC Rms @ sea level Size 8 & 12: 250 VAC Rms @ 50,000 ft. Insulation Resistance 5,000 megohms minimum @ 25°C Typical VSWR for size 8 & 12 PT-SE Types II & III only: 1.2 + .12F (GHz) up to 10 GHz EXPLANATION OF TYPE CLASSIFICATIONS: PT-SE Type I is moisture seal design with internal O-ring. PT-SE Type II is 50 ohm impedance matched version. Contacts terminated to other than 50 ohm cables are therefore not matched. PT-SE Type III is 50 ohm contact, non-serviceable after assembly. Solders are non-impedance matched contacts. CONTACT FINISHES: Suffix Finish 1 0.00020 min. silver over copper flash 2 0.00005 min. gold (Knoop hardness 130-200) over silver 3 0.00010 min. gold (Knoop hardness 130-200) over silver 4 0.00010 min. gold (Knoop hardness 130-200) over copper 5 0.00005 min. gold (Knoop hardness 130-200) over nickel E 0.00005 min. gold (Knoop hardness 90 max.) over copper F 0.00005 min. gold (Knoop hardness 130-200) over copper H 0.00010 min. gold (Knoop hardness 130-200) over copper TYPICAL MINIATURE CRIMP COAX SOCKET CONTACT has crimp socket outer contact with a solder pin inner contact TYPICAL MINIATURE CRIMP COAX PIN CONTACT has crimp pin outer contact with a solder socket inner contact

for miniature cylindrical connectors, cont. solder (MIL-DTL-26482 Series 1 type) - application data H G L F H G L F PIN SOCKET MATING PIN DIA MATING PIN DIA SOLDER COAX CONTACTS For use in Miniature Solder Type Connectors: PT, SP, and MS/PT Styles Cable Contact Part Number Contact Size Dimensional Data (See Drawings above) Crimp Ferrule Tools Retainer Nut Wrench Pin Socket G Dia. H Dia. ±0.001 F Across Flats ±0.004 L Length Ref. MIL-T-22910/7-1 Tool Use with Die Part Number MIL-C-22520/5-01 Tool Use with Die Part Number MIL-C-22520/10-01 Tool Use with Die Part NumberPin Socket RG-58C/U, RG-141A/U, RG-303/U 21-33020-2 21-33019-2 8S 0.040 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 RG-59B/U, RG-62A/U, RG-62B/U, RG-210/U 21-33020-1 21-33019-1 8L 0.040 M22910/7-18 (B) M22520/5-45 (B) 11-8676-3 21-33020-3 21-33019-3 8S 0.040 RG-142B/U, Times MI51115 21-33020-7* 21-33019-7* 8S 0.040 RG-161/U, RG-174A/U, RG-179B/U, RG-187A/U, RG-188A/U, RG-316/U 21-33020-32* 21-33019-32* 12S 0.0300 M22520/5-03 (A) M22520/5-08 (A) M22520/5-35 (B) M22520/10-05 (A) 11-8676-1 RG-178B/U 21-33020-4 21-33019-4* 8S 0.040 M22520/5-33 (B) M22520/10-05 (B) 11-8676-2 RG-196A/U 21-33020-31† 21-33061-31*† 12S 0.0300 M22520/5-33 (B) M22520/10-05 (B) 11-8676-1 RG-180B/U, RG-195A/U, Raychem 5022D1312-9 21-33020-5* 21-33019-5* 8S 0.040 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 Raychem 5021D1331-9 21-33020-6* 21-33019-6* 8S 0.040 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 Thermatics 2929-29 21-33020-33 21-33061-33 12S 0.0200 NOTE: Contacts can be ordered by part numbers given in chart NOTE: Size 8S and 12S contacts are used with connector inserts through shell size 18 only. For larger connector shell sizes, use size 8L contacts. CONTACT FINISH: For all contacts in this series feature 0.000050 minimum gold (Knoop hardness 130-200). * Consult Amphenol, Sidney NY for availability CRIMPING TOOLS: Italicized letters in parenthesis that follow positioner part numbers indicate applicable die closure. Commercial equivalents with the same die closure dimension may be used. † 21-33020-31 and 21-33061-31 only mate with each other

for miniature cylindrical connectors, cont. crimp SE (MIL-DTL-26482 Series 1 type) - application data SE CRIMP COAX CONTACTS For use in Miniature Crimp Type Connectors: PT-SE, SP-SE, and MS/PT-SE Styles Cable Contact Part Number Contact Size Type Finish on Mating Parts Dimensional Data (See Drawings above) Crimp Ferrule Tools Retainer Nut Wrench Installation Tools G Dia. H Dia. ±0.001 F Across Flats ±0.004 L Length Ref. Insertion Removal Pin Socket Pin Socket MIL-T-22910/7-1 Tool Use with Die Part Number MIL-C-22520/5-01 Tool Use with Die Part Number MIL-C-22520/10-0 Tool Use with Die Part Number RG-55B/U, RG-142A/U, RG-142B/U, RG-223/U 21-33012-21 21-33012-25 21-33011-21 21-33011-25 I II 2 0.0355 M22520/5-19 (B) M22520/10-07 (A) 11-8676-2 11-8369-5 11-8660-5 11-7880-8 11-8154-1 21-33038-21 21-33038-25* 21-33037-21 21-33037-25 I II 4 21-33138-21( )* 21-33138-25( )* 21-33137-21( )* 21-33137-25( )* I II ** RG-58C/U, RG-141A/U, RG-303/U 21-33012-22 21-33012-26 21-33011-22 21-33011-26 I II 2 0.0355 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 11-8369-4 11-8660-4 11-7880-8 11-8154-1 21-33038-22* 21-33038-26* 21-33037-22 21-33037-26* I II 4 21-33138-22( )* 21-33138-26( )* 21-33137-22( ) 21-33137-26( )* I II ** RG-59B/U, RG-62A/U, RG-62B/U, RG-210/U 21-33012-36 21-33011-36 8 II 2 0.0355 11-8660-5 11-7880-8 11-8154-121-33038-36* 21-33037-36 8 II 4 RG-140/U, RG-302/U 21-33012-37* 21-33011-37* 8 II 2 0.0355 M22520/5-19 (B) M22520/10-07 (A) 11-8676-2 11-8369-5 11-8660-5 11-7880-8 11-8154-121-33038-37* 21-33037-37* 8 II 4 RG-161/U, RG-174A/U, RG-179B/U, RG-187A/U, RG-188A/U, RG-316/U 21-33012-34 21-33012-30 21-33011-34 21-33011-30 I II 2 0.0355 M22910/7-12 (B) M22520/5-03 (A) M22520/5-08 (A) M22520/5-35 (B) M22520/10-05 (A) 11-8676-2 11-8369-2 11-8660-2 11-7880-8 11-8154-1 21-33038-34 21-33038-30 21-33037-34 21-33037-30 I II 4 21-33138-34( )* 21-33138-30( )* 21-33137-34( )* 21-33137-30( )* I II ** 21-33012-1 21-33012-4 21-33011-1 21-33011-4 I II 2 0.0200 11-8154-2 21-33038-1* 21-33038-4 21-33037-1* 21-33037-4* I II 4 21-33138-1( )* 21-33138-4( )* 21-33137-1( ) 21-33137-4( )* I II ** RG-178B/U, RG-196A/U 21-33012-35 21-33011-35 8 I 2 0.0355 M22520/5-33 (B) 11-8676-2 11-8369-1 11-8660-1 11-7880-8 11-7880-821-33038-35 21-33037-35 8 I 4 21-33012-3* 21-33012-5 21-33011-3* 21-33011-5 I II 2 0.0200 11-8154-2 21-33038-3* 21-33038-5 21-33037-3* 21-33037-5* I II 4 21-33138-3( )* 21-33138-5( )* 21-33137-3( )* 21-33137-5( )* I II NOTE: Contacts can be ordered by part numbers given in chart See finish options for SE crimp Miniature contacts listed on page 44. Replace the parenthesis of the contact part number with the finish suffix number. However, you should consult Amphenol, Sidney, NY regarding the availability of all finish choices for each part number. * Consult Amphenol, Sidney NY for availability CRIMPING TOOLS: Italicized letters in parenthesis that follow positioner part numbers indicate applicable die closure. Commercial equivalents with the same die closure dimension may be used. CHART CONTINUES ON NEXT PAGE MATING PIN DIA H G PIN F L MATING PIN DIA H G SOCKET F L NOTE: All contacts of the same size and the same inner and outer contact diameters (G & H) will mate with each other.

for miniature cylindrical connectors, cont. crimp SE (MIL-MDL-26482 Series 1 type) - application data, cont. SE CRIMP COAX CONTACTS For use in Miniature Crimp Type Connectors: PT-SE, SP-SE, and MS/PT-SE Styles Cable Contact Part Number Contact Size Type Finish on Mating parts Dimensional Data Crimp Ferrule Tools Retainer Nut Wrench Installation Tools G Dia. H Dia. ±0.001 F Across Flats ±0.004 L Length Ref. Insertion Removal Pin Socket Pin Socket MIL-T-22910/7-1 Tool Use with Die Part Number 47MIL-C-22520/5-01 Tool Use with Die Part Number MIL-C-22520/10-0 Tool Use with Die Part Number RG-180B/U, RG-195A/U 21-33012-24 21-33012-46* 21-33011-24 21-33011-46* I II 2 0.0355 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 11-8369-4 11-8660-4 11-7880-8 11-8154-1 21-33038-24 21-33038-46* 21-33037-24 21-33037-46* I II 4 21-33138-24( )* 21-33138-46( )* 21-33137-24( )* 21-33137-46( )* I II Raychem 9527E1118, RG-180B/U, RG-195A/U 21-33106-40( ) 21-33105-40( ) 12 III 0.0200 ± 0.0005 0.128 0.899 0.879 Daniels GS200 Tool with G2P330 or M22520/31-01 Tool with Positioner M22520/31-02 11-8674-2 11-7880-12 11-8154-2 RG-188 or RG-316 Double Braid 21-33012-6* 21-33012-7* 21-33011-6* 21-33011-7* I II 2 0.0200 11-8676-1 11-8369-2 11-8660-2 11-7880-12 11-8154-2 21-33038-6* 21-33038-7* 21-33037-6* 21-33037-7* I II 4 21-33138-6( )* 21-33138-7( )* 21-33137-6( )* 21-33137-7( )* I II ** Thermax 50C-25ADS-1 21-33012-44 21-33011-44 8 II 2 0.0355 11-8660-4 11-7880-8 11-8154-121-33038-44* 21-33037-44* 8 II 4 RG-195 Double Braid 21-33012-28 21-33011-28 8 I 2 0.0355 11-8660-4 11-7880-8 11-8154-121-33038-28* 21-33037-28* 8 I 4 RG-122/U, Raychem 5022E5111 21-33012-23 21-33012-27 21-33011-23 21-33011-27 I II 2 0.0355 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 11-8369-4 11-8660-4 11-7880-8 11-8154-1 21-33038-23* 21-33038-27 21-33037-23* 21-33037-27 I II 4 21-33138-23( )* 21-33138-27( )* 21-33137-23( )* 21-33137-27( )* I II ** Raychem 9530D5314 21-33012-31 21-33011-31 8 I 2 21-33038-31 21-33037-31 8 I 4 Raychem 9527A1317 21-33012-39 21-33011-39 8 II 2 0.0355 M22520/5-41 (B) M22520/10-07 (B) 11-8676-2 11-8369-4 11-8660-4 11-7880-8 11-8154-121-33038-39* 21-33037-39* 8 II 4 Raychem 7527A1318 21-33012-40* 21-33011-40 8 II 2 0.0355 M22520/5-03 (A) M22520/5-08 (A) M22520/5-35 (B) M22520/10-05 (A) 11-8676-2 11-8369-2 11-8660-2 11-7880-8 11-8154-121-33038-40* 21-33037-40* 8 II 4 Westrex 199-49-1, Tensolite 30850/87T-1 21-33012-43 21-33011-43 12 II 2 0.0200 M22520/5-33 (B) M22520/10-05 (B) 11-8676-1 11-8369-1 11-8660-1 11-7880-12 11-8154-2 21-33038-43 21-33037-43 12 II 4 NOTE: Contacts can be ordered by part numbers given in chart ** See finish options for SE crimp Miniature contacts listed on page 44. Replace the parenthesis of the contact part number with the finish suffix number. However, you should consult Amphenol, Sidney, NY regarding the availability of all finish choices for each part number. * Consult Amphenol, Sidney NY for availability CRIMPING TOOLS: Italicized letters in parenthesis that follow positioner part numbers indicate applicable die closure. Commercial equivalents with the same die closure dimension may be used.

for miniature cylindrical connectors R (TP) R D Dia. R .120 Dia. for Shell Sizes 6-22 PC & PT .147 Dia. for Size 24 PT .150 Dia. for SP only No. 4 Screw for PC & PT No. 6 Screw for SP and for Size 24 PT FLANGE MOUNTED CONNECTORS F FR B CUT-OUT FOR PT ONLY PIN LOCATION FOR PC ONLY SECTION JAM NUT MOUNTINGS N CUT-OUT SOLDER RECEPTACLE JAM NUT RECEPTACLE (See dimensions above) BOX RECEPTACLE (See dimensions above) HERMETIC RECEPTACLES FLANGE MOUNTED CONNECTORS All flange mounting PT connectors use standard MS mounting dimensions. They cannot be back panel mounted due to coupling clearance. The PTB (thru-bulkhead) type connector must also be back panel mounted on one side. Flange gaskets are available for both series, see page 37. Shell Size R (TP) D Dia. PT, PTB SP PT SP, PTB 6 .469 .641 .323 .439 8 .594 .734 .449 .563 10 .719 .812 .573 .680 12 .812 .938 .699 .859 14 .906 1.031 .823 .984 16 .969 1.125 .949 1.108 18 1.062 1.203 1.073 1.233 20 1.156 1.297 1.199 1.358 22 1.250 1.375 1.323 1.483 24 1.375 1.449 1.449 - JAM NUT MOUNTINGS The jam nut design has become very popular because it allows bench wiring of harness assemblies. The labor saving often offsets the added cost of the jam nut receptacle which is due to the self contained “O” ring and the extra nut. Shell Size R +.010 -.000 B +.000 -.010 F ±.010 P Panel Thickness Min. Max. 24 1.634 1.575 - .062 .250 HERMETIC RECEPTACLE MOUNTINGS This series must be mounted in such a way as to preserve the hermetic seal provided by the glass insert. Mounting data for box and jam nut receptacles is given above. Cut-out required for solder mounting receptacles (N) is given below. The finish of each of these hermetic receptacles is fused electro- deposited tin for easy solderability, and protected by a special lacquer for optimum shelf life. The lacquer will not interfere with any soldering operation. Low temperature solder should be used and the addition of a solder fillet at arrow points on drawing at right is recommended. Care must be taken that the operating temperature of the final assembly does not rise above the melting point of tin (440° F). Shell Size N Max. 6 .458 8 .582 10 .692 12 .801 14 .926 16 1.051 18 1.176 20 1.395 22 1.375 24 1.520 F FR B CUT-OUT FOR PT ONLY PIN LOCATION FOR PC ONLY SECTION JAM NUT MOUNTINGS

Other Amphenol Miniature Cylindrical Connectors Geophysical Miniature Cylindricals Designed for the Geophysical industry’s rugged environments, the Amphenol® RPT Series connector has custom features that provide reliability in extreme temperature and moisture conditions. The unique shell design provides stronger shells along with an anodized (non-conductive) finish for greater salt, corrosion and abrasion resistance. Coupling nuts are manufactured with round detent holes and are sold separately for greater customer flexibility. See product data sheet #146. RJ Field Bayonet Cylindricals Amphenol PCD division provides MIL-DTL-26482 bayonet coupling cylindrical connectors with an RJ45 Ethernet interface*. These are designed for use in all levels of harsh environments from industrial to mil-aero applications providing IP67 protection from dust, fluids, vibration, shock and traction. The Amphenol® RJ Field allows the use of Ethernet Class D/Cat 5 and Cat 5e connections for 10 BaseT, 100 Base TX, or 1000 BaseT networks. It works with any standard RJ45 cordset with no extra tooling. It also offers reinforced EMI protection. For more information go online to www.rjfield.com or ask for the Field Series brochure. * RJ Field Bayonet and other Field Series products are available through Amphenol PCD. These include RJF TV within MIL-DTL-38999 Series III threaded coupling connectors, and RJF 544 within ECTA push-pull plastic shell coupling.