SMPJ5.0 CHENDA | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
Stand-off Voltage - 5.0 to 100 Volts Peak Pulse Power: 5000 Watts Mechanical Data SMP Dimensions in inches and (millimeters) ƹ Excellent clamping capability ³ Low dynamic impedance ³ Solder dip 260 °C max. 10 s, per JESD 22-B106 Case : JEDEC SMP Molded plastic body Terminals : Tin plated leads, solderable per J-STD- 002 and JESD22-B102 Mounting Position : Any 0D[LPXP5DWLQJV (OHFWULFDO&KDUDFWHULVWLFV Ratings at TA = 25°C unless otherwise specified PARAMETER SYMBOL UNIT Max Peak power dissipation, with a 10/1000us waveform（1）（2 ） PPPM W 5000 Power dissipation, on infinite heat sink at TL=75℃（2） PD W 8.0 Peak forward surge current, 8.3 ms single half sine-wave unidirectional only （3） IFSM A 400 Operating junction and storage temperature range TJ,TST G ℃ -55 to +150 Maximum instantaneous forward voltage at 100A for unidirectional only(4) VFM V 3.5 RθJ-A ℃/W 75 RθJ-L ℃/W 15 Junction to ambient Junction to lead Notes: (1) Non-repetitive current pulse, per Fig. 3 and derated above TA= 25℃per Fig.2. (2) Mounted on 0.31 x 0.31" (8.0 x 8.0 mm) copper pads to each terminal (3) Measured on 8.3ms single half sine-wave or equivalent square wave,duty cycle=4 pulses per minute maximum. (4) V F=3.5V Max for devices of VBR≤220v，and VF=5.0v Max for devices of VBR＞220v. (5) Mounted on minimum recommended pad layout.
Rev:2019A0 Page :2https://www.microdiode.com ELECTRICAL CHARACTERISTICS(TA=25°C unless otherwise noted) Part No. Peak Power Dissipation 10/1000μ sec(W) Reverse Stand-Off Voltage V RWM (V) Breakdown Voltage V BR (V) Min @ I T Breakdown Voltage V BR (V) Max @ I T Test Current I T (mA) Max Clamping Voltage V C (V)@ I PP Peak Pulse Current I PP (A) Reverse Leakage I R (μA) @ V RWM SMPJ5.0 THRU SMPJ100CA Stand-off Voltage - 5.0 to 100 Volts Peak Pulse Power: 5000 Watts
Rev:2019A0 Page :3https://www.microdiode.com Typical Characteristics 0 4.0 IPPM(%) T（ms） FIG3: Pulse Waveform 150 100 3.02.01.0 TJ=25℃ Pulse Width(td) is defined as the Point where the Peak Current Decays to 50% of IPPM 10/1000μs Waveform as Defined by R.E.A. tr=10μs Peak Value IPPM Half Value - IPP IPPM td 0.001 0.01 0.1 1 10 1000 0.1 tp(s) Rth(℃/W) TJ（℃） 100 100 0 200 PPP or IPP(%) FIG2: Pulse Power or Current vs. Initial Junction Temperature 100 175 150 1251007550 25 0.1μs 10μs1μs 100μs 1.0ms 10ms 0.1 td(μs) PPPM(KW) FIG1:Peak Pulse Power Rating Curve 1.0 100 Non-Repetitive Pulse Waveform shown in Fige.3 TA=25℃ Copper Pad Areas 0 10 100 IFSM(A) Number of Cycles FIG5: Maximum Non-Repetitive Surge Current 400 TJ=TJMax. 8.3ms Single Half Sine-Wave 1.5 PD(W) TL(℃) FIG6:Steady State Power Dissipation 20025 50 75 100 125 150 175 3.0 4.5 6.0 7.5 9.0 10.5 FIG4:Typical Transient Thermal Impedance 8.0 SMPJ5.0 THRU SMPJ100CA Stand-off Voltage - 5.0 to 100 Volts Peak Pulse Power: 5000 Watts
https://www.microdiode.com Rev:2019A0 Page :4 Important Notice and Disclaimer Microdiode Electronics (Jiangsu) reserves the right to make changes to this document and its products and specifications at any time without notice. Customers should obtain and confirm the latest product information and specifications before final design,purchase or use. Microdiode Electronics (Jiangsu) makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, not does Microdiode Electronics (Jiangsu) assume any liability for application assistance or customer product design. Microdiode Electronics (Jiangsu) does not warrant or accept any liability with products which are purchased or used for any unintended or unauthorized application. No license is granted by implication or otherwise under any intellectual property rights of Microdiode Electronics (Jiangsu). Microdiode Electronics (Jiangsu) products are not authorized for use as critical components in life support devices or systems without express written approval of Microdiode Electronics (Jiangsu). E Note: based on the center of the small pad,Maximum Displacement 0.3mm。 0RXQWLQJ3DG/D\\RXW(unit:mm) A 5.40 B 5.90 C 2.10 D 1.90 Dim Millimeters B A D C E 4.00 SMPJ5.0 THRU SMPJ100CA Stand-off Voltage - 5.0 to 100 Volts Peak Pulse Power: 5000 Watts