SMDA MCC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

N VOLTAGE VBR @1 mA VOLTS CLAMPING VOLTAGE VC @ 1 Amp (FIGURE 2) VOLTS CLAMPING VOLTAGE VC @5 Amp (FIGURE2) VOLTS LEAKAGE CURRENT ID @ VWM µA CAPACITANCE (f=1 MHz) @0V C pF TEMPERATURE COEFFICIENT OF VBR áVBR Mv/°C PART NUMBER DEVICE MARKING MIN MAX MAX MAX TYP MAX SMDA03 SDK 3.3 4 7 9 200 800 -3 SMDA03C SDL 3.3 4 7 9 200 400 -5 SMDB03 PDK 3.3 4 7 9 200 800 -3 SMDB03C PDL 3.3 4 7 9 200 400 -5 SMDA05 SDA 5.0 6 9.8 11 20 600 3 SMDA05C SDB 5.0 6 9.8 11 40 300 1 SMDB05 PDA 5.0 6 9.8 11 20 600 3 SMDB05C PDB 5.0 6 9.8 11 40 300 1 SMDA12 SDC 12.0 13.3 19 24 1 185 10 SMDA12C SDD 12.0 13.3 19 24 1 94 8 SMDB12 PDC 12.0 13.3 19 24 1 185 10 SMDB12C PDD 12.0 13.3 19 24 1 94 8 SMDA15 SDE 15.0 16.7 24 30 1 140 13 SMDA15C SDF 15.0 16.7 24 30 1 70 11 SMDB15 PDE 15.0 16.7 24 30 1 140 13 SMDB15C PDF 15.0 16.7 24 30 1 70 11 SMDA24 SDG 24.0 26.7 43 55 1 90 30 SMDA24C SDH 24.0 26.7 43 55 1 45 28 SMDB24 PDG 24.0 26.7 43 55 1 90 30 SMDB24C PDH 24.0 26.7 43 55 1 45 28 DESCRIPTION (300 and 500 watt) This 8 pin 4 line Unidirectional or Bidirectional array is designed for use in applications where protection is required at the board level from voltage transients caused by electrostatic discharge (ESD) as defined by IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4 and effects of secondary lighting. These arrays are used to protect any combination of 4 lines. The SMDA/B product provides board level protection from static electricity and other induced voltage surges that can damage sensitive circuitry. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays protect 3.0/3.3 Volt components such as DRAM’s, SRAM’s, CMOS, HCMOS, HSIC, and low voltage interfaces up to 24Volts. FEATURES MECHANICAL

  • Protects 3.0/3.3 up through 24V Components • Molded SO-8 Surface Mount
  • Protects 4 lines Unidirectional or Bidirectional • Weight: 0.066 grams (approximate)
  • Provides electrically isolated protection • Body Marked with Logo, and device number
  • SO-8 Packaging • Pin #1 defined by DOT on top of package MAXIMUM RATINGS PACKAGING
  • Operating Temperatures: -550C to +1500C • Tape & Reel EIA Standard 481-1-A
  • Storage Temperature: -550C to +1500C • 13 inch reel 2,500 pieces (OPTIONAL)
  • SMDA Peak Pulse Power: 300 Watts (8/20 µsec, Figure 1) • Carrier tubes 95 pcs per (STANDARD)
  • SMDB Peak Pulse Power: 500 Watts (8/20 µsec, Figure 1)
  • Pulse Repetition Rate: <.01% ELECTRICAL CHARACTERISTICS PER LINE @ 250C Unless otherwise specified Part numbers with a “C” suffix are bidirectional devices SMDA/B03 THRU SMDA/B24C TVSarrayÔ Ô Series www.mccsemi.com /G01/G02/G03/G04/G05/G06/G07/G05/G08/G08/G09/G04/G03/G02/G0A/G0B/G06/G07omponents

21201 Itasca Street Chatsworth

/G07/G18/G06/G19/G0F/G1A/G0F/G0F /G1B/G15/G05/G1C/G09/G1D/G06/G1E/G1F/G0F/G1F/G20/G06/G21/G10/G0F/G22/G23/G19/G1A/G1A /G24/G0A/G25/G1D/G06/G06/G06/G1E/G1F/G0F/G1F/G20/G06/G21/G10/G0F/G22/G23/G19/G1A/G19 MCC

NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off Voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. WAVE FORMS FIGURE 1 FIGURE 2 Peak Pulse Power Vs Pulse Time Pulse Wave Form MOUNTING PAD SO-8 CIRCUIT DIAGRAM SO-8 PACKAGE 0 10 20 30 100 t -- Time in microsec Ip p - Pe ak Pu lse Cu rre nt Ip Peak Value -- Ipp Half-Value --Ipp

8 X 20 Waveform

t td 0.245 MIN 0.045±.005 .160±.005 .050 TYP .030±.005 INCHES MILLIMETERS MAXMINDIM MAXMIN 0.197 A 0.188 4.77 5.00 0.1580.150 3.81 4.01 0.0690.053 1.35 1.75 0.0210.011 0.28 0.53 0.0500.016 0.41 1.27 0.050 BSC 1.27 BSC 0.0100.006 0.15 0.25 0.0080.004 0.10 0.20 0.2060.189 4.80 5.23 B C D F G J K L 0.244P 0.228 5.79 6.19 UNIDIRECTIONAL BIDIRECTIONAL www.mccsemi.com MCCSMDA/B03 thru SMDA/B24C