SM30 BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Opposed-Mode Infrared Photoelectric Sensors for Especially Demanding Applications

  • Stainless steel or plastic barrel models
  • Very high excess gain; 150 m (500 ft) sensing range; 880 nm Infrared LED
  • Positive sealing eliminates even capillary leakage; lens is quad-ring sealed; exceeds NEMA 6P (IP67) ratings – ideal for equipment wash-down environments
  • EZ-BEAM ® technology provides reliable sensing without the need for adjustment
  • Modulation frequency “A” is standard; frequencies “B” and “C” also available for preventing crosstalk in multiple-sensor applications (emitter and opposed receiver frequencies must match)
  • AC- and DC-operated receiver models available; emitters feature Universal voltage
  • Range for all models: 150 m (500 ft) WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Modulation Frequency1 Housing Cable2 Power Supply Output Type A B C Emitter Models SMA30PEL SMA30PELB SMA30PELC Plastic 2 m (6.5 ft) 2-wire Cable Universal: 12 to 240 V ac, 10 to 30 V dc – SMA30PELQD SMA30PELQDB SMA30PELQDC 3-pin Mini-style QD3 SMA30SEL SMA30SELB SMA30SELC Stainless Steel 2 m (6.5 ft) 3-wire Cable SMA30SELQD SMA30SELQDB SMA30SELQDC 3-pin Mini-style QD3 DC Receivers SM30PRL SM30PRLB SM30PRLC Plastic 2 m (6.5 ft) 4-wire Cable 10 to 30 V dc Bi-Modal™ NPN or PNP SM30PRLQD SM30PRLQDB SM30PRLQDC 4-pin Mini-style QD SM30SRL SM30SRLB SM30SRLC Stainless Steel 2 m (6.5 ft) 4-wire Cable SM30SRLQD SM30SRLQDB SM30SRLQDC 4-pin Mini-style QD AC Receivers SM2A30PRL SM2A30PRLB SM2A30PRLC Plastic 2 m (6.5 ft) 2-wire Cable 24 to 240 V ac SPST Solid-state, L.O. SM2A30PRLQD SM2A30PRLQDB SM2A30PRLQDC 3-pin Mini-style QD3 SM2A30SRL SM2A30SRLB SM2A30SRLC Stainless Steel 2 m (6.5 ft) 3-wire Cable SM2A30SRLQD SM2A30SRLQDB SM2A30SRLQDC 3-pin Mini-style QD3 SM2A30PRLNC SM2A30PRLNCB SM2A30PRLNCC Plastic 2 m (6.5 ft) 2-wire Cable SPST Solid-state, D.O. SM2A30PRLNCQD SM2A30PRLNCQDB SM2A30PRLNCQDC 3-pin Mini-style QD3 SM2A30SRLNC SM2A30SRLNCB SM2A30SRLNCC Stainless Steel 2 m (6.5 ft) 3-wire Cable SM2A30SRLNCQD SM2A30SRLNCQDB SM2A30SRLNCQDC 3-pin Mini-style QD3 1 Any emitter and receiver shown here can be used together, if they have the same modulation frequency. 2 Standard 2 m (6.5 ft) cable and integral QD models are listed. Models with a quick disconnect require a mating cordset. To order the 9 m (30 ft) PVC cable model, add the suffix "W/30" to the cabled model number. For example, SM30PRLBW/30. 3 AC models with QD require SM30CC model cables. SM30 Series 30 mm Barrel Sensors Original Document 03541 Rev. G

25 May 2017

1 = Brown (red/black for QD emitters/receivers) 3 = Blue (red/white for QD emitters/receivers) 4 = Green (green for QD emitters/receivers) Emitters—Cabled 10-30V dc or 12-240V ac Emitters—QD 10-30V dc or 12-240V ac AC Receivers—Cabled 24-240V ac Load AC Receivers—QD 24-240V ac Load Note: AC emitters are not polarity-sensitive when powered by dc voltage. For QD emitters, use a SM30CC model cordset to match cable colors. *Connect the green wire to earth ground whenever a stainless steel model is powered by ac voltage. (Cabled plastic models have no green wire.) Key 1 = Brown 2 = White 3 = Blue 4 = Black DC Receivers—NPN 10-30V dc Load Light Operate 10-30V dc Load Dark Operate DC Receivers—PNP 10-30V dc Load Light Operate 10-30V dc Load Dark Operate Cabled wiring diagrams are functionally identical. SM30 Series 30 mm Barrel Sensors 2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 03541 Rev. G

Supply Voltage and Current Emitters: 12 to 240V ac (50/60 Hz) or 10-30V dc at 20 mA, 10% maximum ripple DC Receivers: 10 to 30V dc at 10 mA maximum (exclusive of load); 10% maximum ripple AC Receivers: 24 to 240V ac (50/60 Hz) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration DC Receivers: Bi-Modal™ output (PNP sourcing or NPN sinking). Selection of light/dark operate and sourcing or sinking configuration dependent on hookup. AC Receivers: SPST solid-state switch; light operate (LO) or dark operate (DO) dependent on model. Output Rating DC Receivers: 250 mA continuous Output saturation voltage (PNP & NPN configuration) < 1 volt at 10 mA and < 2 volts at 250 mA Off-state leakage current < 10 microamps AC Receivers: Maximum steady-state load capability is 500 mA Inrush capability: 10 amps for 1 second (non-repeating) Off-state leakage: current < 1.7 mA rms On-state voltage drop: < 3.5 volts rms across a 500 mA load; < 5 volts rms across a 15 mA load Output Protection Circuitry Outputs of dc receivers are short circuit protected Output Response Time 10 milliseconds on/off Repeatability “A” frequency models: 1 ms “B” frequency models: 1.5 ms “C” frequency models: 2.3 ms Indicators Internal red LED, visible through the lens or from side of the sensor. Emitters: Red “Power ON” indicator LED DC Receivers: Lights whenever receiver sees its modulated light source AC Receivers: Lights whenever receiver’s output is conducting Construction Fully epoxy-encapsulated tubular threaded housing, positive sealed at both ends, quad-ring sealed acrylic lens. Plastic models: 30 mm diameter thermoplastic polyester housing and jam nuts. Stainless Steel models: 30 mm diameter 303 stainless steel housing and jam nuts. Environmental Rating Exceeds NEMA 6P and IEC IP67 Connections PVC-jacketed 2 m or 9 m cables or Mini-style quick-disconnect (QD) fitting are available. QD cables are ordered separately. Operating Conditions Temperature: − 40 °C to +70 °C ( − 40 °F to +158 °F) 90% at +50 °C maximum relative humidity (non-condensing) Required Overcurrent Protection WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply. Supply wiring leads < 24 AWG shall not be spliced. For additional product support, go to www.bannerengineering.com. Supply Wiring (AWG) Required Overcurrent Protection (Amps) 20 5.0 22 3.0 24 2.0 26 1.0 28 0.8 30 0.5 Certifications Dimensions All measurements are listed in millimeters [inches], unless noted otherwise. Cabled Models Jam Nuts(2 Provided)AlignmentIndicator (Receivers) M30 x 1.5Thread 102 mm(4.0") QD Models Jam Nuts(2 Provided)AlignmentIndicator (Receivers) M30 x 1.5Thread 114 mm(4.5") SM30 Series 30 mm Barrel Sensors P/N 03541 Rev. G www.bannerengineering.com - Tel: +1-763-544-3164 3

10 m33 ft 100 m330 ft1000 m3300 ft1 m3.3 ft 1000 10000 100000 EXCESSGAIN DISTANCE SM30 SeriesOpposed Mode Beam Pattern 225 m750 ft180 m600 ft135 m450 ft90 m300 ft45 m150 ft0 500 mm 1000 mm 1500 mm 500 mm 1000 mm 1500 mm 20 in 40 in 60 in 20 in 40 in 60 in DISTANCE SM30 SeriesOpposed Mode Accessories Cordsets 3-Pin Mini-Style Cordsets Model Length Style Dimensions Pinout (Female) SM30CC-306 1.83 m (6 ft) Straight 7/8-16UN-2B ø 25.5 52 Typ. 1 = Red/Black 3 = Red/White 4 = Green SM30CC-312 3.66 m (12 ft) 4-Pin Mini-Style Cordsets Model Length Style Dimensions Pinout (Female) MBCC-406 1.83 m (6 ft) Straight 7/8-16UN-2B ø 25.5 52 Typ. 1 = Brown 2 = White 3 = Blue 4 = Black MBCC-412 3.66 m (12 ft) MBCC-430 9.14 m (30 ft) Apertures APG30S 0.20 in. Used with SM30 and SMI30 models. SM30 Series 30 mm Barrel Sensors 4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 03541 Rev. G

  • Right-angle bracket with curved slot for versatile orientation
  • Clearance for M6 (¼ in) hardware
  • Mounting hole for 30 mm sensor
  • 12-ga. stainless steel

69 A B

C Hole center spacing: A to B=40 Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5 SMB30C

  • 30 mm split clamp, black PBT bracket
  • Stainless steel mounting hardware included
  • Mounting hole for 30 mm sensor A B Hole center spacing: A=ø 45 Hole size: B=ø 27.2 SMB30MM
  • 12-ga. stainless steel bracket with curved mounting slots for versatile orientation
  • Clearance for M6 (¼ in) hardware
  • Mounting hole for 30 mm sensor A B C Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1 SMB30SC
  • Swivel bracket with 30 mm mounting hole for sensor
  • Black reinforced thermoplastic polyester
  • Stainless steel mounting and swivel locking hardware included B A Hole center spacing: A=ø 50.8 Hole size: A=ø 7.0, B=ø 30.0 Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. SM30 Series 30 mm Barrel Sensors © Banner Engineering Corp. All rights reserved