SLR10.100 PULS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

SLR10.100

  • Input: AC 230V/115V, DC 240-375 V
  • Output: 24 V/10 A
  • High overload current, no switch-off
  • N+1 redundancy, RDY relay contact
  • Robust mechanics and EMC CUL/CSA-C22.2 EMC and Low Volt. UL60950 E137006 UL508 LISTED IND. CONT. EQ. No 950-M90

18 WM, 60°C

Efficiency, Reliability etc.* Start / Overload Behaviour Output * For further information see data sheets „The SilverLine“, „SilverLine Family Branches“ and mechanics data sheet Input voltage AC100-120/220-240 V (switchable), 47-63 Hz (85-132 VAC / 176-264 VAC, 240-375 VDC) Note: At DC input, always leave the switch in the 230V position. Input current < 6 A (switch in 115V position) < 2.8 A (switch in 230V position) DCin at open output 8 mA (preserves battery sources) Inrush current typ. < 30 A at 264 V AC and cold start Unit is internally fused (fuse not accessible). External fuse not necessary, but recommended (common 10A, B-type 'circuit-breaker' switch used anyway to fuse the input lines). Transient handling Transient resistance acc. to VDE 0160 / W2 (750 V / 1.3 ms), for all load conditions. Hold-up time > 25 ms at 196 VAC, 24 V / 10 A (see diagram overleaf) Efficiency typ. 89 % (230 VAC, 24 V / 10 A) Losses typ. 26.7 W (230 VAC, 24 V / 10 A) MTBF 390.000 h acc. to Siemensnorm SN 29500 (24 V/10 A, 230 VAC, T amb = +40 °C) Life cycle (electrolytics) The unit exclusively uses longlife electrolytics specified for +105°C (cf. ’The SilverLine’, p.2). Start-up delay typ. 0.1 s Rise time ca. 5-20 ms, depending on load Overload Behaviour  Special PULS Over- load Design (see diagram overleaf)  20% power boost – no disconnection, no hiccup if overloaded – high overload current (up to 1.6 I Nom), Vout is gradually reduced with increasing current. – 12A short-term , at 45°C or forced cooling even continuous Advantages:  High short-circuit current, giving large ’start-up window’: unit starts reliably even with awkward loads (DC-DC converters, motors).  No ’sticking’ such as can occur with fold-back characteristics  Secondary fuses operate reliably Rated output voltage 24 V DC For balanced current sharing during parallel operation: Soft characteristic (25.2 V DC ±2% at no-load, 24 V DC ±0.5% at nominal load, almost linear characteristic curve) Output noise suppression Radiated EMI values below EN50081-1, even when using long, unscreened output cables. Ambient temperature range Tamb Operation: 0°C...+70°C (>60°C: Derating) Storage: -25°C...+85°C Rated continuous loading with convection cooling amb=0°C - 60°C T amb=0°C - 45°C

24 V / 10 A

short-term also at 60 °C Output is protected against short circuit, open circuit and overload Derating typ. 12 W/K (at T amb=+60°C...+70°C) Voltage regulation better than 2% Vout overall Ripple / Noise < 30 mV PP, (20 MHz bandw., 50 Ω measurem.) Overvolt. protection typ. 35 V Parallel operation yes, current sharing via soft characteristic (see diagram) Front panel indicator Green LED RDY relay contact T y p e c l o s e s  opens  Electrical isolation  Contact rating normally open contact when output voltage > 22.1V ±4% when output voltage < 19.8V ±4% 500V DC to output voltage 1A at 28V DC Order information Order number Description SLR10.100 SL10.100 SLS10.100 SLZ01 N+1 redundancy* Basic version without redundancy* Safety Cover* Screw mounting set, two needed per unit

Your partner in power supply: European Power Supply Manufacturers Association PULS GmbH Arabellastraße 15 D-81925 München Tel.: +49 89 9278-0 www.puls-power.com Fax: +49 89 9278-199 Data sheet 2/2 slr10e100 / 031217 Bayerns Best 50 Czech 100 Best EuropeÕs 500 Unless otherwise stated, specifications are valid for AC 230V input voltage, +25°C ambient temperature, and 5 min. run-in time. They are subject to change without prior notice. Construction / Mechanics* Further information Housing dimensions and Weight W x H x D  Free space for ventilation W e i g h t 120 mm x 124 mm x 102 mm (+ DIN Rail) above/below 25 mm recommended left/right 15 mm recommended 980 g Design advantages:  Input and output pluggable by means of Combicon ® plug connector  Ensure strain relief of the plug connectors when installing the unit. Further information, especially about E M C  Connections  Safety, Approvals  Mechanics and Mounting see page 2 of „The SilverLine“ data sheet. For detailed dimensions see SilverLine mechanics data sheet SLR2.5/ 5/ 10 100 210 230 250 270 290 310 330 350 370 390 Input voltage VDCin [V] Hold-up time [ms] Partial load DCin Nominal load Power Boost 80 100 120 140 160 180 200 220 240 Input voltage VACin [V] Hold-up time [ms] Power Boost Switch pos. 115V ACinSwitch pos. 230V Nominal load Nom. load Partial load Power Boost Partial load 3 5 7 9 11 13 Output current Iout [A] Efficiency [%]

230 V ACin / 24 V DCout

Output voltage Vout [V] Output current Iout [A] Tamb = 60°C / 45°C / 25°C / 0°C Efficiency (typ.) Hold-up time (typ.) Output characteristic (min.) with Partial Load = 120 W Nominal Load = 240 W Power Boost = 288 W Power wiring SLR10.100 GND +24V N +L SLR10.100 –N +L