SLO BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

  • An easy-to-use self-contained opposed-mode sensor pair in a rugged U-shaped housing
  • Easy and economical to mount
  • Molded-in beam guides simplify mounting and beam placement
  • 30 mm slot width for a wide variety of sensing applications
  • Applications include hole detection, gear tooth detection, edge guiding and counting of opaque materials
  • 10 V dc to 30 V dc operation
  • Bipolar PNP/NPN outputs
  • Choose 1 millisecond or 300 microsecond response
  • 2 mm effective beam
  • Dark or light operate
  • Choose integral, unterminated cable or QD models WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Models Sensing Beam Slot Width Cable1 Output Response Repeatability SLO30VB6 Infrared, 890 nm 30 mm (1.2 in) 2 m (6.5ft) 5-wire cable Bipolar NPN/PNP 1 ms 250 µs SLO30VB6Q 5-Pin Euro-style QD SLO30VB6Y 2 m (6.5ft) 5-wire cable 300 µs 75 µs SLO30VB6YQ 5-Pin Euro-style QD Overview The SLO Series Slot Sensor (sometimes called a “Fork Sensor”) comprises an opposed-mode emitter and its receiver inside a single convenient housing. Opposed-mode sensing is very reliable, and the single self- contained housing provides easy installation, with no sensor alignment required. In addition, the molded-in arrow on the emitter portion of the housing and the slotted design on the receiver portion of the housing show at a glance the position of the beam, simplifying installation placement. Receiver (Beam Aligns at Groove) Power ON LEDSignal LED Emitter

Figure 1. Features disconnect require a mating cordset.

23 February 2018

Figure 2. Typical Applications Note: Quick disconnect (QD) wiring diagrams are functionally identical.

Supply Voltage and Current 10 to 30V dc, 30 mA Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Bipolar: PNP and NPN Output Rating 150 mA each output Output Protection Circuitry Protected against output short-circuit and false pulse on power up Output Response Time 1 millisecond or 300 microseconds, depending on model Repeatability 250 microseconds or 75 microseconds, depending on model Operating Conditions Operating Temperature: −40 °C to +70 °C (−40 °F to +158 °F) 90% at +50 °C maximum relative humidity (non-condensing) Slot Opening 30 mm (1.18 in) wide × 45 mm (1.8 in) deep; beam is 10 mm (0.4 in) from outer edge Adjustments None Indicators Green: Power on/off indicator Amber: Signal condition indicator Construction Housing: ABS and polycarbonate Lenses: acrylic Connections 2 m (6.5 ft) or 9 m (30 ft) 5-conductor PVC-jacketed attached cable or 5-pin Euro-style quick-disconnect Environmental Rating IEC IP67; NEMA 6 Required Overcurrent Protection WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Overcurrent protection is required to be provided by end product application per the supplied table. Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply. Supply wiring leads < 24 AWG shall not be spliced. For additional product support, go to www.bannerengineering.com. Supply Wiring (AWG) Required Overcurrent Protection (Amps) 20 5.0 22 3.0 24 2.0 26 1.0 28 0.8 30 0.5 Certifications E224071 Dimensions M12 x 1 Signal LED (Amber) Power LED (Green) 20.2 mm (0.80") 18.8 mm(0.74") 6.0 mm(0.24") 10.9 mm(0.43") 10.0 mm(0.39) 30.2 mm(1.19") 45.0 mm(1.77") 72.0 mm(2.84") 40.0 mm(1.58") 52.0 mm(2.05") All measurements are listed in millimeters [inches], unless noted otherwise. SLO Series Slot Sensor P/N 60073 Rev. B www.bannerengineering.com - Tel: +1-763-544-3164 3

5-Pin Threaded M12/Euro-Style Cordsets—Single Ended Model Length Style Dimensions Pinout (Female) MQDC1-501.5 0.50 m (1.5 ft) Straight 44 Typ. ø 14.5 M12 x 1 2 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray MQDC1-506 1.83 m (6 ft) MQDC1-515 4.57 m (15 ft) MQDC1-530 9.14 m (30 ft) MQDC1-506RA 1.83 m (6 ft) Right-Angle 32 Typ.[1.26"] 30 Typ.[1.18"] ø 14.5 [0.57"] M12 x 1 MQDC1-515RA 4.57 m (15 ft) MQDC1-530RA 9.14 m (30 ft) Brackets SMBSL

  • Angled bracket
  • 304 stainless steel
  • Hardware included 6 X Ø5.541 Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. SLO Series Slot Sensor © Banner Engineering Corp. All rights reserved