SLH2815S/KR

SLH2805S CRANE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

Features

small size, 0.8 inches2 (5.16 cm2) Operating temperature -55° to +125°C• Qualified to MIL-PRF-38534 Class H and K• Radiation hardness assurance (RHA) to level R 100 kRad(Si)• Input voltage range 16 to 40 VDC • Fully isolated, magnetic feedback• Inhibit function• Indefinite short circuit protection• High power density, 88% efficiency • Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters Crane Aerospace & Electronics Electronics group (Interpoint Brand) PO Box 97005 • Redmond WA 98073-9705 425.882.3100 • power@crane-eg.com www.interpoint.com Page 1 of 10 28 VoLt input – 1.5 Watt – pending reVision c reLease Rev C - 20090318 - Pending Revision C Release

Operating COnditiOns and CharaCteristiCs input Voltage range 16 to 40 VDC continuous•

50 V for 50 msec transient•

1.5 W• Lead soldering temperature (10 sec per lead) 300°C• storage temperature range (case) –65°C to +150°C• capacitive Load Single output models 100 µF• Dual output models 100 µF• case operating temperature (tc) -55°C to +125°C full power• -55°C to +135°C absolute• output Voltage temperature coefficient 100 ppm/°C typical• input to output capacitance 100 to 170 pF typical• isolation 100 megohm minimum at 500 VDC• Any pin to case, except case pin• conversion Frequency (kHz), 28 Vin, full load 25°C, 280 typ • -55°C to +125°C; 220 min, 320 max • derating output power/current (tc) Linearly from 100% at 125°C to 0% at 135°C• inhibit Active low (output disabled)• InH referenced to input common ‣ Active low 0.5 V max ‣ Inhibit pin current < 2mA ‣ Active high (output enabled)• Open collector or unconnected ‣ Pin voltage 7 to 8 volts, typical (open circuit) ‣ Do not apply external pull-up ‣ meChaniCal and envirOnmental size (maximum) See case A2 for dimensions.• Weight (maximum) 12 grams• screening Space Prototype (O), Class H, or Class K Radiation tolerant to Radiation Hardness Assurance (RHA) levels of “-” (O) or “R”, per MIL-STD-38534. Interpoint model numbers use an “O” in the RHA designator position to indicate the “-” (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as “no RHA”. See “Class H and K, QML Screening” tables, page 10. Available configurations: OO, HR, KR Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt – pending reVision c reLease Page 2 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

Fi g u r e 1: pin Ou t Squared corner and dot on top of cover indicate pin one. 1 4 7 5 2 3 See case A2 for dimensions. pin out pin single output dual output

1 Positive Input Positive Input

2 Input Common Input Common

3 Positive Output Positive Output

4 Output Common Output Common

5 Case ground Case ground

6 no connection negative Output

7 Inhibit Inhibit

Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt – pending reVision c reLease Page 3 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

Assurance (RHA) Number of Outputs (S = single, D = dual) ModeL nuMbering Key The SMD number shown is for Class K screening and Radiation Hardness Assurance (RHA) level R. See the SMD for the numbers for other screening and radiation levels. For exact specifications for an SMD product, refer to the SMD drawing. Call your Interpoint representative for status on the SMTR SMD releases which are “in process.” SMDs can be downloaded from: http://www.dscc.dla.mil/programs/smcr sMd nuMbers St a nDa rD MiCrO Ci rCu i t Dr a w i n g (SMD) SLH SiMiLar pa r t 5962R0052601KXC SLH2805S/KR 5962R0052701KXC SLH2812S/KR 5962R0052801KXC SLH2815S/KR 5962R0250401KXC SLH2805D/KR 5962R9955601KXC SLH2812D/KR 5962R9852901KXC SLH2815D/KR ModeL seLection en t e r On e SeLeCt iOn FrO M e aC H Ca t e gOr y SLH28 / BASE MODEL VOUT VALUE nUMBER OF OUTPUTS 1 CASE OPTIOn2 SCREEnIng 3 RHA 4 5 s nO CASE OPTIOnS FOR SLH o o 12 d H r 15 K notes: 1. S is a single output and D is a dual output 2. There are not case options for the SLH. Only the standard case is available. 3. A screening level of O is a Space Prototype and is only used with RHA O. 4. Interpoint model numbers use an “O” in the RHA designator position to indicate the “-” (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as “no RHA. RHA O is only available with Screening level O. For more information see page 10. Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt – pending reVision c reLease Page 4 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

notes: all temperatures refer to case temperature, tc. 1. guaranteed by design, not tested. 2. Specified at 50% load. 3. With a series inductor on the Vin power lead (L in = 6 µH). 4. Maximum duration of short circuit: 90 seconds at 25°C, 30 seconds at 125°C. 5. Load fault is a short circuit into 1 . Recovery is into resistive full load. 6. Transition > 10 µs. 7. Measured from release of inhibit until Vout settles to within 1% of final value at full load with Vin at 28V. 8. Recovery = time to settle to within 1% of Vout final value. Electrical Characteristics: -55° to + 125°C Tc, 28 VDC Vin, 100% load, unless otherwise specified. SIngLE OUTPUT MODELS SLH2805S SLH2812S SLH2815S unitSparaMeter COnDitiOnS MIn TYP MAX MIn TYP MAX MIn TYP MAX Output Current Vin = 16 tO 40 VDC — — 300 — — 125 — — 100 mA Output pOwer Vin = 16 tO 40 VDC — — 1.5 — — 1.5 — — 1.5 W Output rippLe 25°C, 10 kHz tO 2 MHz — 65 150 — 35 200 — 60 200 mV p-p-55 tO +125° C, 10 kHz tO 2 MHz — — 250 — — 300 — — 300 Line reguLatiOn Vin = 16 tO 40 VDC — 115 300 — 60 400 — 60 650 mV LOaD reguLatiOn LOaD 10% tO 100% — 440 700 — 380 700 — 410 700 mV input VOLtage nO LOaD tO FuLL COntinuOuS 16 28 40 16 28 40 16 28 40 VDC TRAnSIEnT 50 ms 1 — — 50 — — 50 — — 50 V input Current nO LOaD — 2.9 17 — 2.3 17 — 2.4 17 mAinHiBiteD — 1.3 5 — 1.3 5 — 1.3 5 input rippLe Current 3 10 kHz - 10 MHz — 85 250 — 75 300 — 60 300 mA p-p eFFiCienCy 25°C, FuLL LOaD 72 79 — 80 87 — 80 88 — %-55 tO +125° C, FuLL LOaD 69 — — 69 — — 69 — — LOaD FauLt 4, 5 SHOrt CirCuit reCOVery 1, 8 — — 30 — — 30 — — 30 ms Step LOaD reSpOnSe 1,5 50% - 100% - 50% tranSient — ±250 ±400 — ±220 ±700 — ±220 ±700 mV pk reCOVery — — 400 — — 400 — — 400 µs Step Line reSpOnSe 16 - 40 -16 VDC tranSient — — ±600 — - ±600 — — ±600 mV pk reCOVery 1, 8 — — 500 — — 500 — — 500 µs Start-up7 DeLay — 1 20 — 1 20 — 1 20 ms OVerSHOOt 1 — — 500 — — 500 — — 500 mV pk CapaCitiVe LOaD 1 25° C, nO eFFeCt On DC perFOrManCe — — 100 — — 100 — — 100 µF Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt – pending reVision c reLease Page 5 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

DUAL OUTPUT MODELS SLH2805D SLH2812D SLH2815D unitSparaMeter COnDitiOnS MIn TYP MAX MIn TYP MAX MIn TYP MAX Output Current 7 EITHER OUTPUT Vin = 16 tO 40 VDC — 150 240 — 62.5 100 — 50 80 mA tOt aL, Vin = 16 tO 40 VDC Output pOwer Vin = 16 tO 40 VDC — — 1.5 — — 1.5 — — 1.5 W Output rippLe ±VOu t 25°C 10 kHz tO 2 MHz — 75 150 — 40 200 — 65 300 mV p-p10 kHz tO 2 MHz — — 250 — — 400 — — 500 Line reguLatiOn Vin = 16 tO 40 VDC +VOu t — 75 400 — 75 700 — 85 650 mV-VOu t — 65 400 — 70 700 — 85 650 LOaD reguLatiOn 8 BALAnCED, 10% tO 100% +VOu t — 310 700 — 350 700 — 370 700 mV-VOu t — 300 700 — 350 700 — 370 700 input VOLtage nO LOaD tO FuLL COntinuOuS 16 28 40 16 28 40 16 28 40 VDC TRAnSIEnT 50 ms 1 input Current nO LOaD — 3.1 17 — 3.1 17 — 3.3 17 mAinHiBiteD — 1.4 5 — 1.4 5 — 1.4 5 input rippLe Current 3 10 kHz - 10 MHz — 80 250 — 90 300 — 100 300 mA p-p eFFiCienCy 25°C, FuLL LOaD 72 80 — 80 87 — 80 87 — %FuLL LOaD 69 — — 69 — — 69 — — LOaD FauLt 4 ±VOu t SHOrt CirCuit reCOVery 1 — — 30 — — 30 — — 30 ms Step LOaD reSpOnSe 5 ±VOut BaLa nCeD LOaD 50% - 100% - 50% tranSient — ±150 ±400 — ±170 ±600 — ±200 ±700 mV pk reCOVery 1 — — 600 — — 360 — — 600 µs Step Line reSpOnSe 1,5 ±VOut, 16 - 40 -16 VDC reCOVery — — 500 — — 500 — — 500 µs Start-up ±VOut DeLay6 — 1 20 — 2 20 — 2 20 ms OVerSHOOt 1 — — 500 — — 500 — — 500 mV pk CapaCitiVe LOaD1 25° C, nO eFFeCt On DC perFOrManCe — — 100 — — 100 — — 100 µF Electrical Characteristics: -55° to + 125°C Tc, 28 VDC Vin, balanced 100% load, unless otherwise specified. notes (see following page) Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt – pending reVision c reLease Page 6 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

0.000 0.000 0.135 (3.43) 0.835 (21.21) 0.270 max(6.98) 0.000 1 4 7 5 2 3 0.235 (5.97) 0.435(11.05) 0.535 (13.59) BOTTOM VIEW CASE A2 0.27 ±0.02 (6.9 ±0.5) Projection Weld Squared corner and dot on top of case indicate pin one. 0.018 ± 0.002 dia. (0.46 ± 0.05) Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin Materials Header Kovar/Nickel/Gold Cover Kovar/Nickel Pins Kovar/Nickel/Gold matched glass seal Case A2, Rev D, 20081119 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. 0.805 max. (20.45) 0.697 (17.70) 0.097 (2.46) 0.980 max. (24.89) Fi g u r e 2: CaSe a2 notes SLH Dual Output Models: all temperatures refer to case temperature, tc 1. guaranteed by design, not tested. 2. Specified at 50%/50% balanced load. 3. With a series inductor on the Vin power lead (L in = 6 µH). 4. Load fault is a short circuit into 1 . Recovery is into resistive full load. 5. Transition > 10 µs. Recovery is time for Vout to settle to within 1% of final value. 6. Measured from release of inhibit until Vout settles to within 1% of final value at full load with Vin at 28V. 7. Maximum specification indicates 80% of the converter’s total power is available from either output, provided the other output carries 20% of the total power. 8. Although no minimum load is required, at no load the output voltage may exceed rating by up to 15%. Electrical Characteristics: -55° to + 125°C Tc, 28 VDC Vin, balanced 100% load, unless otherwise specified. Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converter cases 28 VoLt input – 1.5 Watt Page 7 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

Cl a s s H a n d K, MIl-PRF-38534 ElE M En t Ev a l u a tIo n COmpOnent-level test perfOrmed spaCe prOtOtype (O) nOn-Qml1 Class h Qml Class K Qml m/s2 p3 m/s2 p3 m/s2 p3 Element Electrical yes no yes yes yes yes Element Visual no no yes yes yes yes Internal Visual no N/A yes N/A yes N/A Temperature Cycling no no no no yes yes Constant Acceleration no no no no yes yes Interim Electrical no N/A no N/A yes N/A Burn-in no N/A no N/A yes N/A Post Burn-in Electrical no N/A no N/A yes N/A Steady State Life no N/A no N/A yes N/A Voltage Conditioning Aging N/A no N/A no N/A yes Visual Inspection no no N/A no N/A yes Final Electrical no no yes yes yes yes Wire Bond Evaluation4 no no yes yes yes yes SEM no N/A no N/A yes N/A SLAM™/C-SAM: Input capacitors only (Add’l test, not req. by H or K) no no no yes no yes Notes: 1. Non-QML products do not meet all of the requirements of MIL-PRF-38534. 2. M/S = Active components (Microcircuit and Semiconductor Die) 3. P = Passive components 4. Not applicable to EMI filters that have no wirebonds. Definitions: Element Evaluation: Component testing/screening per MIL-STD-883 as determined by MIL-PRF-38534 SEM: Scanning Electron Microscopy SLAM™: Scanning Laser Acoustic Microscopy C-SAM: C - Mode Scanning Acoustic Microscopy Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt – pending reVision c reLease Page 8 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

Cl a s s H a n d K, MIl-PRF-38534 En vI Ro nM En t a l sC R E EnIn g end item-level test perfOrmed spaCe prOtOtype (O) nOn-Qml1 Class h Qml Class K Qml Non-destruct bond pull2 Method 2023 no yes3 yes Pre-cap Inspection Method 2017, 2032 yes yes yes Temperature Cycle (10 times) Method 1010, Cond. C, -65°C to 150°C, ambient yes yes yes Constant Acceleration Method 2001, 3000 g yes yes yes PIND Test Method 2020, Cond. A no yes3 yes Pre burn-in test yes yes yes Burn-in Method 1015, 125°C case, typical 96 hours 160 hours 2 x 160 hours (includes mid-BI test) yes no no no yes no no no yes Final Electrical Test MIL-PRF-38534 Group A, Subgroups 1 through 6 -55°C, +25°C, +125°C case yes yes yes Radiography Method 2012 N/A N/A yes Post Radiography Electrical Test Room temperature N/A N/A yes Hermeticity Test Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C yes yes yes yes yes yes Final visual inspection Method 2009 yes yes yes Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. Notes: 1. Space Prototype (O), non-QML products, do not meet all of the requirements of MIL-PRF-38534. 2. Not applicable to EMI filters that have no wirebonds. 3. Not required by DSCC but performed to assure product quality. Crane Aerospace & Electronics Power Solutions sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt – pending reVision c reLease Page 9 of 10www.interpoint.com Rev C - 20090318 - Pending Revision C Release

Cl a s s H a n d K, MIl-PRF-38534 Ra dIa tIo n as s uRa nC E radiatiOn hardness assUranCe levels envirOnmental sCreening levels spaCe prOtOtype (O) nOn-Qml2 Class h Qml Class K Qml O1: Standard, no radiation guarantee OO HO N/A r3: Radiation tolerant–Tested lots up to 100 K Rads (Si) total dose SEU guarantee up to 40 MeV N/A HR KR Notes: 1. Interpoint model numbers use an “O” in the RHA designator position to indicate the “-” (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as “no RHA”. 2. Space Prototype (O), non-QML, products do not meet all of the requirements of MIL-PRF-38534. 3. Redmond site, Interpoint, has a Radiation Hardness assurance plan on file with DSCC. Crane Aerospace & Electronics Power Solutions SLH Single and Dual, Rev C - 20090318 - Pending Revision C Release. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. SLH Series is a trademark of Interpoint. Copyright © 1999 - 2009 Interpoint Corporation. All rights reserved. www.interpoint.com Page 10 of 10 sLH single and dual dc/dc converters 28 VoLt input – 1.5 Watt