SLG59H1009V

SLG59H1009V RENESAS | Alldatasheet

Document overview

• Manufacturer or author: pwong
• PDF pages: 25

Technical content

Features

• UL2367 Certified - File Number E468659
• Maximum Continuous Current: 4 A
• Automatic nFET SOA Protection
• 5 W SOA Protection Threshold
• High-performance MOSFET Switch Low RDS ON : 13.1 mΩ at V IN = 22 V Low ΔRDS ON /ΔV IN : < 0.05 mΩ/V Low ΔRDS ON /ΔT: < 0.06 mΩ/°C
• Capacitor-adjustable Inrush Current Control
• Two stage Current Limit Protection: Resistor-adjustable Active Current Limit Internal Short-circuit Current limit
• Open Drain FAULT Signaling
• MOSFET Current Analog Output Monitor: 10 µA/A
• Fast 4 kΩ Output Discharge
• Pb-Free / Halogen-Free / RoHS Compliant Packaging Pin Configuration

Applications

• Power-Rail Switching
• Multifunction Printers
• Large-format Copiers
• Telecommunications Equipment
• High-performance Computing

5 V, 9 V, 12 V, and 20 V Point-of-Load Power Distribution

• Motor Drives ON 1 FAULT CAP GND SEL0 2 VIN 4 VOUT SEL1 RSET IOUT VIN VIN 5 VIN 7 VOUT 12 VOUT VOUT VIN VOUT 8 9 18-pin STQFN 1.6 x 3.0 mm, 0.40mm pitch (Top View) SLG59H1009V

20 V ±10%

3 V FS - Connect

100 kΩ Linear Ramp Control State Machine (CL/SC Detection and Over Temperature Protection) Discharge CMOS Input VIN OVLO 24V RSET 21 kΩ 47 µF RIOUT 84.5 kΩ GND OFF CLOAD = C 4 + C 5 1 to 22 µF 0.1 µF VLOGIC CIOUT 180 pF RPU1 10 kΩ VLOGIC SEL0 SEL1 FAULT VOUT ON CAP RSET VIN IOUT CIN = C 1 + C 2 + C 3 C4 47 µF 22 µF

Revision 1.03 Page 2 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Pin Description

Ordering Information

Pin # Pin Name Type Pin Description

1 ON Input

A low-to-high transition on this pin initiates the operation of the SLG59H1009V’s state machine. ON is an asserted HIGH, level-sensitive CMOS input with ON_V IL < 0.3 V and ON_V IH > 0.9 V. As the ON pin input circuit does not have an internal pull-down resistor, connect this pin to a general-purpose output (GPO) of a microcontroller, an application processor, or a system controller – do not allow this pin to be open-circuited.

2 SEL0 Input

As level-sensitive, CMOS inputs with V IH > 1.65 V, the SEL0 (LSB) and the SEL1 (MSB) pins set the V IN overvoltage lockout threshold. A logic HIGH on either pin is achieved by connecting a 10 kΩ external resistor from the pin in question to the system’s local logic supply.

3 GND GND

Pin 3 is the main ground connection for the SLG59H1009V’s internal charge pump, its gate driver and current-limit circuits as well as its internal state machine. Therefore, use a short, stout connection from Pin 3 to the system’s analog or power plane. 4-8 VIN MOSFET VIN supplies the power for the operation of the SLG59H1009V, its internal control circuitry, and the drain terminal of the nFET load switch. With 5 pins fused together at VIN, connect a 47 μF (or larger) low-ESR capacitor from this pin to ground. Capacitors used at VIN should be rated at 50 V or higher. 9-13 VOUT MOSFET Source terminal of n-channel MOSFET (5 pins fused for VOUT). Connect a 47 μF (or larger) low-ESR capacitor from this pin to ground. Capacitors used at VOUT should be rated at 50 V or higher.

14 SEL1 Input Please see SEL0 Pin Description above

15 FAULT Output

An open drain output, FAULT is asserted within TFAULT LOW when a V IN overvoltage, a current-limit, or an over-temperature condition is detected. FAULT is deasserted within TFAULT HIGH when the fault condition is removed. Connect an 100 kΩ external resistor from the FAULT pin to local system logic supply.

16 CAP Output

A low-ESR, stable dielectric, ceramic surface-mount capacitor connected from CAP pin to GND sets the V OUT slew rate and overall turn-on time of the SLG59H1009V. For best performance, the range for C SLEW values are 10 nF ≤ C SLEW ≤ 20 nF – please see typical characteristics for additional information. Capacitors used at the CAP pin should be rated at 10 V or higher. Please consult Applications Section on how to select C SLEW based on V OUT slew rate and loading conditions.

17 IOUT Output

IOUT is the SLG59H1009V’s power MOSFET load current monitor output. As an analog current output, this signal when applied to a ground-reference resistor generates a voltage proportional to the current through the n-channel MOSFET. The I OUT transfer characteristic is typically 10 μA/A with a voltage compliance range of 0.5 V ≤ VIOUT ≤ 4 V. Optimal I OUT linearity is exhibited for 0.5 A ≤ I DS ≤ 4 A. In addition, it is recommended to bypass the IOUT pin to GND with a 0.18 nF capacitor. 18 RSET Input A 1%-tolerance, metal-film 21 kΩ resistor sets the active current limit of the SLG59H1009V to 4.5 A. Part Number Type Production Flow SLG59H1009V STQFN 18L FC Industrial, -40 °C to 85 °C SLG59H1009VTR STQFN 18L FC (Tape and Reel) Industrial , -40 °C to 85 °C

Revision 1.03 Page 3 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Absolute Maximum Ratings Parameter Description Conditions Min. Typ. Max. Unit VIN to GND Load Switch Input Voltage to GND Continuous -0.3 -- 30 V Maximum pulsed V IN , pulse width < 0.1 s -- -- 32 V VOUT to GND Load Switch Output Voltage to GND -0.3 -- VIN V ON, SEL[1,0], CAP , RSET, IOUT, and FAULT to GND ON, SEL[1,0], CAP , RSET, IOUT, and FAULT Pin Voltages to GND -0.3 -- 7 V TS Storage Temperature -65 -- 150 °C ESD HBM ESD Protection Human Body Model 2000 -- -- V ESD CDM ESD Protection Charged Device Model 500 -- -- V MSL Moisture Sensitivity Level 1 θJA Thermal Resistance 1.6 x 3.0 mm 18L STQFN; De - termined with the device mount - ed onto a 1 in 2, 1 oz. copper pad of FR-4 material -- 40 -- °C/W MOSFET IDS CONT Continuous Current from VIN to VOUT T MOSFET IDS PEAK Peak Current from VIN to VOUT Maximum pulsed switch current, pulse width < 1 ms -- -- 5 A Note: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at thes e or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Electrical Characteristics

VIN = 22 V; C IN = 47 µF, T A = -40 °C to 85 °C, unless otherwise noted. Typical values are at T A = 25 °C Parameter Description Conditions Min. Typ. Max. Unit VIN Operating Input Voltage -- 20 22 V VIN(OVLO) VIN Overvoltage Lockout Threshold V IN ↑; SEL[1,0] = [1,1] 22.7 24 25.2 V VIN(UVLO) VIN Undervoltage Lockout Threshold VIN ↓ 2.4 -- 3.8 V IQ Quiescent Supply Current ON = HIGH; I DS = 0 A -- 0.5 0.6 mA ISHDN OFF Mode Supply Current ON = LOW; I DS = 0 A -- 1 3 µA RDS ON ON Resistance TA = 25 °C; I DS = 0.1 A -- 13.1 14 mΩ TA = 85 °C; I DS = 0.1 A -- 16 16.5 mΩ MOSFET IDS Current from VIN to VOUT Continuous -- -- 4 A ILIMIT Active Current Limit, I ACL VOUT > 0.5 V; R SET = 21 kΩ 4.2 4.5 4.9 A Short-circuit Current Limit, I SCL VOUT < 0.5 V -- 0.5 -- A TACL Active Current Limit Response Time -- 120 -- µs RDISCHRG Output Discharge Resistance 3.5 4.4 5.3 kΩ IOUT MOSFET Current Analog Monitor Output I DS = 1 A 9.3 10 10.7 µA IDS = 3 A 28.5 30 31.5 µA TIOUT IOUT Response Time to Change in Main MOSFET Current CIOUT = 180 pF; Step load 0 to 2.4 A; 0% to 90% I OUT -- 45 -- µs

Revision 1.03 Page 4 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation CLOAD Output Load Capacitance C LOAD connected from VOUT to GND -- 47 -- µF TON_Delay ON Delay Time 50% ON to 10% V OUT ↑; VIN = 22 V; C SLEW = 10 nF; RLOAD = 100 Ω, C LOAD = 10µF -- 0.7 1.2 ms TTotal_ON Total Turn On Time 50% ON to 90% V OUT ↑ Set by External C SLEW 1 ms 50% ON to 90% V OUT ↑; VIN = 22 V; C SLEW = 10 nF; RLOAD = 100 Ω, C LOAD = 10 µF -- 5 8 ms VOUT(SR) VOUT Slew rate 10% V OUT to 90% V OUT ↑ Set by External C SLEW

1 V/ms

10% V OUT to 90% V OUT ↑; VIN = 22 V; C SLEW = 10 nF; RLOAD = 100 Ω, C LOAD = 10 µF 2.7 3.2 3.9 V/ms TOFF_Delay OFF Delay Time 50% ON to V OUT Fall Start ↓; VIN = 22 V; RLOAD = 100 Ω, No C LOAD -- 15 -- µs TFALL VOUT Fall Time 90% V OUT to 10% V OUT ; ON = HIGH-to-LOW; V IN = 22 V; RLOAD = 100 Ω, No C LOAD 10.4 12.7 14.3 µs TFAULT LOW FAULT Assertion Time Abnormal Step Load Current event to FAULT ↓; I ACL = 4.5 A; V IN = 22 V; RSET = 21 kΩ; switch in 5 Ω load -- 80 -- µs TFAULT HIGH FAULT De-assertion Time Delay to FAULT ↑ after fault condition is removed; I ACL = 4.5 A; V IN = 22 V; RSET = 21 kΩ; switch out 5 Ω load -- 180 -- µs FAULT VOL FAULT Output Low Voltage I FAULT = 1 mA -- 0.2 -- V ON_V IH ON Pin Input High Voltage 0.9 -- 5 V ON_V IL ON Pin Input Low Voltage -0.3 0 0.3 V SEL[1,0]_V IH SEL[1,0] pins Input High Voltage 1.65 -- 4.5 V ION(Leakage) ON Pin Leakage Current 1 V ≤ ON ≤ 5 V or ON = GND -- - - 1 µA THERM ON Thermal Protection Shutdown Thresh - old -- 125 -- °C THERM OFF Thermal Protection Restart Threshold -- 100 -- °C Notes: 1. Refer to typical Timing Parameter vs. C SLEW performance charts for additional information when available. Electrical Characteristics (continued) VIN = 22 V; C IN = 47 µF, T A = -40 °C to 85 °C, unless otherwise noted. Typical values are at T A = 25 °C Parameter Description Conditions Min. Typ. Max. Unit

Revision 1.03 Page 5 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation TTotal_ON , T ON_Delay and Slew Rate Measurement 90% V OUT 50% ON TON_Delay VOUT(SR) (V/ms) ON* VOUT TTotal_ON 10% V OUT 50% ON 10% V OUT TOFF_Delay TFALL 90% V OUT *Rise and Fall Times of the ON Signal are 100 ns

Revision 1.03 Page 6 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Typical Performance Characteristics RDS ON vs. Temperature IACL vs. Temperature

Revision 1.03 Page 7 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation IOUT vs. MOSFET IDS IOUT vs. Temperature and MOSFET IDS

Revision 1.03 Page 8 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation VOUT Slew Rate vs. Temperature and C SLEW TTotal_ON vs. C SLEW and Temperature

Revision 1.03 Page 9 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Timing Diagram - Basic Operation including Active C urrent Limit Protection VIN ON Time LOW HIGH TFAULT HIGH VOUT IDS 90% 10% TON_Delay Active Current Limit Operation FAULT HIGH ISCL IACL ISCL IACL ON TFAULT LOW Nominal Steady State Operation Resumes ACL Threshold Triggered Abnormal Step Load Current Event TRISE

Revision 1.03 Page 10 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Timing Diagram - Active Current Limit & Thermal Pro tection Operation VOUT IDS 90% 10% TON_Delay Active Current Limit Operation Thermal Protection Operation ISCL IACL ISCL IACL TFAULT HIGH FAULT VIN ON Time LOW HIGH Nominal Steady State Operation Resumes TFAULT LOW Die temp > THERM ON Abnormal Step Load Current Event TRISE TTotal_ON Die temp < THERM OFF

Revision 1.03 Page 11 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Timing Diagram - Basic Operation including Active C urrent + Internal FET SOA Protection VIN ON Time LOW HIGH TFAULT HIGH VOUT IDS 90% 10% 0.2s TON_Delay Active Current Limit Operation FAULT HIGH ISCL IACL ISCL IACL ON TFAULT LOW ACL Threshold Triggered Nominal Steady State Operation resumes once overload condition is removed Automatic restart after 0.2s “cool off” delay and normal operation resumes if overload condition is removed FET SOA Threshold Triggered and FET is turned off ACL Threshold Triggered Abnormal Step Load Current Event SOA Threshold TRISE Decreasing R LOAD drops V OUT SOA Protection

Revision 1.03 Page 16 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Applications Information High Voltage GreenFET Safe Operating Area Explained Renesas’s High Voltage GreenFET load switches incor porate a number of internal protection features tha t prevents them from damaging themselves or any other circuit or subcirc uit downstream of them. One particular protection f eature is their Safe Operation Area (SOA) protection. SOA protection is automatically activated under overpower and, in som e cases, under overcurrent conditions. Overpower SOA is activated if package power dissipation exceeds an internal 5 W threshold longer than 2.5 ms. High Voltage GreenFET devices will quickly switch off (open circuit) upon overpower detection and automatically resume (close) nominal operation once overpower condition no longer exists. One possible way to have an overpower condition trigger SOA protection is when High Voltage GreenFET products are enabled into heavy output resistive loads and/or into large load capacitors. It is under these conditions to follow carefully the “Safe Start-up Loading” guidance in the Applications section of the datasheet. During an overcurrent condition, High Voltage GreenFET devices will try to limit the output current to the level s et by the external R SET resistor. Limiting the output current, however, ca uses an increased voltage drop across the FET’s channel because the FET’s RDS ON increased as well. Since the FET’s RDS ON is larger, package power dissipation also increases. If the re sultant increase in package power dissipation is hi gher/equal than 5 W for longer than 2.5 ms, internal SOA protection will be triggered and the FET will open circuit (switch off). Every time SOA protection is triggered, all High Voltage GreenFET devices will automatically attempt to resume nominal operation after 160 ms. Safe Start-up Condition SLG59H1009V has built-in protection to prevent over-heating during start-up into a heavy load. Overloading the VOUT pin with a capacitor and a resistor may result in non-monoto nic V OUT ramping. In general, under light loading on VOUT, V OUT ramping can be controlled with C SLEW value. The following equation serves as a guide: where T RISE = Total rise time from 10% V OUT to 90% V OUT VIN = Input Voltage CSLEW = Capacitor value for CAP pin When capacitor and resistor loading on VOUT during start up, the following tables will ensure V OUT ramping is monotonic without triggering internal protection: Note 2: Select the closest-value tolerance capacitor. Safe Start-up Loading for V IN = 22 V (Monotonic Ramp) Slew Rate (V/ms) C SLEW (nF) 2 CLOAD (µF) R LOAD (Ω) 0.5 66.7 500 80 1.0 33.3 250 80 1.5 22.2 160 80 2.0 16.7 120 80 2.5 13.3 100 80 CSLEW = TRISE VIN x 4.9 µA x 20

Revision 1.03 Page 17 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Power Dissipation The junction temperature of the SLG59H1009V depends on different factors such as board layout, ambient temperature, and other environmental factors. The primary contributor to the increase in the junction temperature of the SLG59H1009V is the power dissipation of its power MOSFET. Its power dissipation and the junction temperature in nominal operating mode can be calculated using the following equations: where: PD = Power dissipation, in Watts (W) RDS ON = Power MOSFET ON resistance, in Ohms (Ω) IDS = Output current, in Amps (A) and where: T J = Junction temperature, in Celsius degrees (°C) θJA = Package thermal resistance, in Celsius degrees per Watt (°C/W) TA = Ambient temperature, in Celsius degrees (°C) In current-limit mode, the SLG59H1009V’s power diss ipation can be calculated by taking into account th e voltage drop across the load switch (V IN -V OUT ) and the magnitude of the output current in current-limit mode (I ACL ): where: PD = Power dissipation, in Watts (W) V IN = Input Voltage, in Volts (V) RLOAD = Load Resistance, in Ohms (Ω) IACL = Output limited current, in Amps (A) VOUT = R LOAD x I ACL PD = RDS ON x I DS TJ = PD x θ JA + T A PD = (V IN -V OUT ) x I ACL or PD = (V IN – (R LOAD x I ACL )) x I ACL

1. Since the VIN and VOUT pins dissipate most of the heat generated during high-load current operation, it is highly recommended
2. To minimize the effects of parasitic trace inductance on normal operation, it is recommended to connect input C IN and output
3. The GND pin should be connected to system analog or power ground plane.
4. 2 oz. copper is recommended for high current operation.

Figure 9. SLG59H1009V Evaluation Board

Revision 1.03 Page 20 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Package Top Marking System Definition 1009V Part Code Pin 1 Identifier WWNNN Date Code + LOT Code ARR Assembly + Rev. Code 1009V - Part ID Field WW - Date Code Field NNN - Lot Traceability Code Field 1 A - Assembly Site Code Field 2 RR - Part Revision Code Field 2 Note 1: Each character in code field can be alphanumeric A-Z and 0-9 Note 2: Character in code field can be alphabetic A-Z

Revision 1.03 Page 21 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Package Drawing and Dimensions 18 Lead TQFN Package 1.6 x 3 mm (Fused Lead) JEDEC MO-220, Variation WCEE

Revision 1.03 Page 22 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation SLG59H1009V 18-pin STQFN PCB Landing Pattern Note: All dimensions shown in micrometers ( µm)

Revision 1.03 Page 23 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation Tape and Reel Specifications Carrier Tape Drawing and Dimensions Recommended Reflow Soldering Profile Please see IPC/JEDEC J-STD-020: latest revision for reflow profile based on package volume of 2.64 mm 3 (nominal). More information can be found at www.jedec.org. Package Type # of Pins Nominal Package Size [mm] Max Units Reel & Hub Size [mm] Leader (min) Trailer (min) Tape Width [mm] Part Pitch [mm] per Reel per Box Pockets Length [mm] Pockets Length [mm] STQFN 18L 1.6x3mm 0.4P FC Green 18 1.6 x 3 x 0.55 3,000 3,000 178 / 60 100 400 100 400 8 4 Package Type Pocket BTM Length Pocket BTM Width Pocket Depth Index Hole Pitch Pocket Pitch Index Hole Diameter Index Hole to Tape Edge Index Hole to Pocket Center Tape Width A0 B0 K0 P0 P1 D0 E F W STQFN 18L 1.6x3mm 0.4P FC Green Refer to EIA-481 specification

Revision 1.03 Page 24 of 24 SLG59H1009V A 22 V, 13.1 mΩ, 4 A Load Switch with V IN Lockout Select and MOSFET Current Monitor Output ©2022 Renesas Electronics Corporation

Revision History

2/2/2022 1.03 Updated Company name and logo Added SOA Protection Threshold to Features Fixed typos 12/12/2018 1.02 Updated style and formatting Updated Charts Added Scopeshots Added Layout Guidelines Fixed typos 10/26/2016 1.01 Updated General Description and Featu res 5/13/2016 1.00 Production Release

TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com Contact Information For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) © 2021 Renesas Electronics Corporation. All rights reserved.