SLC1 BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

  • No user adjustments – Adaptive Digital Logic (ADL ™ )1 provides revolutionary self-learning capability.
  • Continuous automatic internal adjustment of sensing threshold and drift compensation.
  • Registration accuracy of ± 0.3 mm (0.012") typical at web speeds up to 1.5 m per second (5 ft per second)
  • Reliably detects the presence of most types of labels on web backing ◦ Clear labels on an opaque backing ◦ Clear labels on a clear backing ◦ Opaque labels on an opaque backing ◦ Opaque labels on a clear backing
  • Perfect for label-registering applications, and also for label-counting tasks in slitting or rewinding applications.
  • Heavy-duty metal housing, 1 mm (0.04") slot Model Number Supply Voltage Cable Output Type User Adjustments SLC1BB6 10 to 30 V dc 5-wire 2 m (6.5 ft) Bipolar (NPN and PNP) None Required SLC1BB6Q 5-pin Euro-style (QD) To order the 9 m (30 ft) cable models, add the suffix “W/30” to the model number of the cabled version (e.g., SLC1BB6 W/30). A model with a QD connector requires an accessory mating cable. WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Overview 3 4

Figure 1. SLC1 Label Sensor Features settings; no user adjustments are necessary.

1 Patent pending

14 May 2014

Figure 4. For best repeatability, align the labels' flat sides between types, or in response to an internal error indication. for 1 second or longer and then ON again. The SLC1 may also be reset using the sensor’s gray wire. 250 ms, whichever is greater.

  • Moisture in the sensing slot
  • Extreme and prolonged web flutter
  • Label jams (labels touching both the top and the bottom sensor forks) If an internal error occurs, correct its cause and perform a reset (cycle the sensor power OFF for at least 1 second and ON again or toggle the gray wire to the opposite polarity for >100 milliseconds). Maintenance The SLC1 Series sensor may be disassembled for periodic cleaning, as needed. Use a 7/64" hex key to remove the four screws at the bottom and remove the bottom fork for cleaning. Clean the fork surfaces with a mild solvent, such as isopropyl alcohol, taking care to avoid the clear indicator light window. Repairs Contact Banner Engineering for troubleshooting of this device. Do not attempt any repairs to this Banner device; it contains no field-replaceable parts or components. If the device, device part, or device component is determined to be defective by a Banner Applications Engineer, they will advise you of Banner's RMA (Return Merchandise Authorization) procedure. Important: If instructed to return the device, pack it with care. Damage that occurs in return shipping is not covered by warranty. C-GAGE SLC1 Series Label Sensor P/N 59369 Rev. B www.bannerengineering.com - tel: 763-544-3164 3

Outputs ON during gap (Turn OFF at leading edge of label) Outputs ON during label (Turn ON at leading edge of label) Key Load Load 10-30 V dc Load Load 10-30 V dc 1 - brown 2 - white 3 - blue 4 - black 5 - gray *Toggle to opposite polarity for > 100 milliseconds to reset microprocessor. Specifications Supply Voltage and Current 10 to 30 V dc (10% max. ripple) @ less than 60 mA (exclusive of load ) Supply Protection Circuitry Protected against reverse polarity and transient voltages Power-Up or Reset Delay 1 second typical (outputs are non-conducting during this time) Output Configuration Bipolar: one current-sourcing (PNP) and one current-sinking (NPN) open-collector transistor Output Rating 150 mA max. (each output) OFF-state leakage current: < 5 microamps at 30 V dc Output saturation voltage: < 1 V at 10 milliamps dc; < 1.6 V at 150 milliamps dc Output Protection Protected against continuous overload and short-circuit of outputs Overload trip point: > 200 milliamps, typical, at 20 °C Output Invert Control/Reset Gray wire has dual functionality, and may be controlled by a PLC Input impedance: 10 K Ω Outputs ON during gap (turn OFF at leading edge of label): leave open, or connect to 0 to +1 V dc Outputs ON during label (turn ON at leading edge of label): connect to +5 to 30 V dc Microprocessor reset: toggle gray wire to opposite polarity for > 100 milliseconds Environmental Rating IP67, NEMA 6 Operating Conditions Temperature: 5 °C to 50 °C (41 °F to 122 °F) Maximum relative humidity: 90% at 50 °C, non-condensing Registration Accuracy ±0.3 mm (0.012 inch) typical, at web speeds up to 1.5 m per second (5 ft per second) 2 Maximum Counting Speed Web speed of 10 m per second (33 ft per second) 2 Minimum Sensing Speed Web speed of 100 mm per minute (4 inches per minute) 2 Response Time 100 μ s 2 Maximum Switching Speed 1 kHz 2 Minimum Gap or Label Size 2 mm (0.08 inch) Adjustments No user adjustments; automatic continuous adjustment of sensing threshold and drift compensation under internal microprocessor control Adjustment interval: every 250 milliseconds or 4 labels, whichever is greater Indicators Two LEDs, green and amber Green ON: power to sensor is ON Green flashing at 4 Hz: output is overloaded Amber ON: NPN and PNP outputs are ON Green and amber flashing alternately at 1 Hz: internal error; reset sensor Construction Housings are machined aluminum with black anodized finish Connections 2 m (6.5 ft) or 9 m (30 inches) 5-wire attached cable, or 5-pin Euro- style quick-disconnect fitting Cables for QD models are purchased separately Certifications Approval expected: UL 2 Based on 3.2 mm (0.125 inch) gap between labels. Instantaneous web speed, not average web speed, must be used to determine actual operating speeds in stepped-advance label systems. C-GAGE SLC1 Series Label Sensor 4 www.bannerengineering.com - tel: 763-544-3164 P/N 59369 Rev. B

Remove 4 screws for cleaning. Use 7/64" hex key Clearance for M4 (#8) screws (2 holes) 10.2 mm (0.40") 25.4 mm (1.00") 3.8 mm (0.15") 32.8 mm (1.30") 1 mm (0.04") 8.9 mm (0.35") 23.1 mm (0.91") 40.8 mm (1.61") 88.9 mm (3.49") 30.5 mm (1.20") 68.8 mm (2.71") SLC1BB6 Label Sensor SENSING AREA Green: power on Green flashing: output overload Yellow: outputs conducting bn: +10 to 30 V dc bu: common wh: NPN output bk: PNP output gy: output invert / reset Accessories All measurements are listed in millimeters (inches). 5-Pin Threaded M12/Euro-Style Cordsets (Single Ended) Model Length Style Dimensions Pinout (Female) MQDC1-501.5 0.50 m (1.5 ft) Straight 44 Typ. ø 14.5 M12 x 1 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray MQDC1-506 1.83 m (6 ft) MQDC1-515 4.57 m (15 ft) MQDC1-530 9.14 m (30 ft) MQDC1-506RA 1.83 m (6 ft) Right-Angle 32 Typ. [1.26"] 30 Typ. [1.18"] ø 14.5 [0.57"] M12 x 1 MQDC1-515RA 4.57 m (15 ft) MQDC1-530RA 9.14 m (30 ft) Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. C-GAGE SLC1 Series Label Sensor P/N 59369 Rev. B www.bannerengineering.com - tel: 763-544-3164 5

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. C-GAGE SLC1 Series Label Sensor www.bannerengineering.com - tel: 763-544-3164